Application of Atmospheric-Pressure Jet Plasma in the Presence of Acrylic Acid for Joining Polymers without Adhesives.

This study investigates the treatment of surfaces with jet plasma at atmospheric pressure in the presence of acrylic acid as a resource-saving and efficient approach to joining polymers on polystyrene (PS) and polyamide 12 (PA 12) surfaces. Acrylic acid was added in order to introduce functional groups to the polymer surfaces. XPS analysis revealed a high density of oxygen-containing groups, e.g., carboxylic acid groups, on the polymer surfaces, the detailed composition depending on the polymer. The AFM measurements indicated that the modification of polyamide resulted in morphological changes and an increase in surface roughness due to polymer recrystallization. When the surface-modified polymers were brought in contact under a load, significant adhesion between the polymer surfaces was measured. In particular, PS and PA 12, which are otherwise difficult to join by gluing, could readily be connected in this way. The joint polymers could be separated intentionally by immersion in water, thus enabling the recycling of the materials. The resistance of the joint to water depends on the polymer system, with polyamide providing strikingly higher resistance than polystyrene. Accordingly, treating the joint polymers with water allows debonding on demand, particularly when PS is involved. Exposure of modified polymer surfaces to solutions of metal ions increased the resistance of joint polymers to water.

Copper Ions Absorbed on Acrylic-Acid-Grafted Polystyrene Enable Direct Bonding with Tunable Bonding Strength and Debonding on Demand.

Recycling adhesively bonded polymers is inconvenient due to its expensive separation and removal of adhesive residues. To tackle this problem, adhesive technologies are needed allowing debonding on demand and which do not contaminate the surface of the substrate. Direct bonding enabled by oxygen plasma treatment has already achieved substantial adhesion between flat substrates. However, debonding takes place by water, thus limiting the applications of this technology to water-free environments. The work presented in the following shows that this drawback can be overcome by grafting acrylic acid and adding copper(II) ions on the surface of polystyrene. In this process, the number of functional groups on the surface was significantly increased without increasing the surface roughness. The bonding strength between the substrates could be increased, and the process temperature could be lowered. Nevertheless, the samples could be debonded by exposure to EDTA solution under ultrasound. Hence, by combining acrylic acid grafting, variations in the bonding temperatures and the use of copper(II) ions, the bonding strength (5 N to >85 N) and the debonding time under the action of water can be tuned over large ranges (seconds to complete resistance).

Sustainable wood electronics by iron-catalyzed laser-induced graphitization for large-scale applications.

Ecologically friendly wood electronics will help alleviating the shortcomings of state-of-art cellulose-based "green electronics". Here we introduce iron-catalyzed laser-induced graphitization (IC-LIG) as an innovative approach for engraving large-scale electrically conductive structures on wood with very high quality and efficiency, overcoming the limitations of conventional LIG including high ablation, thermal damages, need for multiple lasing steps, use of fire retardants and inert atmospheres. An aqueous bio-based coating, inspired by historical iron-gall ink, protects wood from laser ablation and thermal damage while promoting efficient graphitization and smoothening substrate irregularities. Large-scale (100 cm2), highly conductive (≥2500 S m-1) and homogeneous surface areas are engraved single-step in ambient atmosphere with a conventional CO2 laser, even on very thin (∼450 µm) wood veneers. We demonstrate the validity of our approach by turning wood into highly durable strain sensors, flexible electrodes, capacitive touch panels and an electroluminescent LIG-based device.

Natural Wood-Based Catalytic Membrane Microreactors for Continuous Hydrogen Generation.

The development of controlled processes for continuous hydrogen generation from solid-state storage chemicals such as ammonia borane is central to integrating renewable hydrogen into a clean energy mix. However, to date, most reported platforms operate in batch mode, posing a challenge for controllable hydrogen release, catalyst reusability, and large-scale operation. To address these issues, we developed flow-through wood-based catalytic microreactors, characterized by inherent natural oriented microchannels. The prepared structured catalysts utilize silver-promoted palladium nanoparticles supported on metal-organic framework (MOF)-coated wood microreactors as the active phase. Catalytic tests demonstrate their highly controllable hydrogen production in continuous mode, and by adjusting the ammonia borane flow and wood species, we reach stable productivities of up to 10.4 cmH23 min-1 cmcat-3. The modular design of the structured catalysts proves readily scalable. Our versatile approach is applicable for other metals and MOF combinations, thus comprising a sustainable and scalable platform for catalytic dehydrogenations and applications in the energy-water nexus.

Review on Adhesives and Surface Treatments for Structural Applications: Recent Developments on Sustainability and Implementation for Metal and Composite Substrates.

Using adhesives for connection technology has many benefits. It is cost-efficient, fast, and allows homogeneous stress distribution between the bonded surfaces. This paper gives an overview on the current state of knowledge regarding the technologically important area of adhesive materials, as well as on emergent related technologies. It is expected to fill some of the technological gaps between the existing literature and industrial reality, by focusing at opportunities and challenges in the adhesives sector, on sustainable and eco-friendly chemistries that enable bio-derived adhesives, recycling and debonding, as well as giving a brief overview on the surface treatment approaches involved in the adhesive application process, with major focus on metal and polymer matrix composites. Finally, some thoughts on the connection between research and development (R&D) efforts, industry standards and regulatory aspects are given. It contributes to bridge the gap between industry and research institutes/academy. Examples from the aeronautics industry are often used since many technological advances in this industry are innovation precursors for other industries. This paper is mainly addressed to chemists, materials scientists, materials engineers, and decision-makers.