Quality of cellulose and biostimulant extracts from Oedogonium calcareum cultivated during primary wastewater treatment.

A practical two-product cascading biorefinery was developed to extract a biostimulant and cellulose from the freshwater filamentous macroalga Oedogonium calcareum grown while treating primary wastewater. Biostimulant production provides a valuable extract with production of disinfected residual biomass for further product development. Both Escherichia coli and F-specific RNA bacteriophage, indicators of human pathogens contamination, were absent from the residual biomass. The chemical composition of the biostimulant was complex, consisting of growth-promoting substances, free amino acids, and minerals. The O. calcareum cellulose fractions yielded between 9.5% and 10.1% (w/w) with purities from 84% to 90% and closely resembled microcrystalline cellulose. Biostimulant extraction improved cellulose quality by increasing crystallinity from 59% to 62%. Biomass condition, drying process, and biostimulant production influenced the crystallinity index. This study demonstrates a two-step process of biostimulant and cellulose extraction from wastewater-grown Oedogonium, simultaneously disinfecting biomass and isolating high-quality cellulose as a sustainable alternative to conventional extraction methods.

Production and Assessment of Poly(Lactic Acid) Matrix Composites Reinforced with Regenerated Cellulose Fibres for Fused Deposition Modelling.

Additive manufacturing can be a valuable tool to process polymeric composites reinforced with bio-based fibres, extending their use and opening new opportunities for more environmentally friendly materials. In this work, poly(lactic acid) (PLA) composites reinforced with regenerated cellulose fibres (lyocell) were processed into novel filaments and used for 3D printing. The Young's modulus of the filaments increased with the addition of fibres, but substantial porosity was observed in formulations with 20 and 30 wt% of fibre content. Nonetheless, the composites were easily printed, and the formulation with 10 wt% of fibres presented the best tensile properties of 3D printed samples with average tensile strength, Young's modulus, and strain at break of 64.2 MPa, 4.56 GPa, and 4.93%, respectively. It has been shown in this study that the printing process contributes to fibre alignment with small variations depending on the printing speed. Printed composite samples also had superior thermo-mechanical stability with a storage modulus up to 72 times higher than for neat PLA at 80 °C after the composite samples were heat-treated. In general, this work supports the potential use of regenerated cellulose fibres to reinforce PLA for 3D printing applications.

Potential of Cellulose Microfibers for PHA and PLA Biopolymers Reinforcement.

Cellulose nanocrystals (CNC) have attracted the attention of many engineering fields and offered excellent mechanical and physical properties as polymer reinforcement. However, their application in composite products with high material demand is complex due to the current production costs. This work explores the use of cellulose microfibers (MF) obtained by a straightforward water dispersion of kraft paper to reinforce polyhydroxyalkanoate (PHA) and polylactic acid (PLA) films. To assess the influence of this type of filler material on the properties of biopolymers, films were cast and reinforced at different scales, with both CNC and MF separately, to compare their effectiveness. Regarding mechanical properties, CNC has a better reinforcing effect on the tensile strength of PLA samples, though up to 20 wt.% of MF may also lead to stronger PLA films. Moreover, PHA films reinforced with MF are 23% stronger than neat PHA samples. This gain in strength is accompanied by an increment of the stiffness of the material. Additionally, the addition of MF leads to an increase in the crystallinity of PHA that can be controlled by heat treatment followed by quenching. This change in the crystallinity of PHA affects the hygroscopicity of PHA samples, allowing the modification of the water barrier properties according to the required features. The addition of MF to both types of polymers also increases the surface roughness of the films, which may contribute to obtaining better interlaminar bonding in multi-layer composite applications. Due to the partial lignin content in MF from kraft paper, samples reinforced with MF present a UV blocking effect. Therefore, MF from kraft paper may be explored as a way to introduce high fiber concentrations (up to 20 wt.%) from other sources of recycled paper into biocomposite manufacturing with economic and technical benefits.

Densification of Bamboo: State of the Art.

Densification processes are used to improve the mechanical and physical properties of lignocellulose materials by either collapsing the cell cavities or by filling up the pores, consequently reducing the void volume fraction. This paper focuses on an extensive review of bamboo densification process, which is achieved by compressing the material in the direction perpendicular to the fibers using mainly two different techniques: an open system, thermo-mechanical (TM), or a closed system, viscoelastic-thermal-compression (VTC). The main aim of bamboo densification is to decrease its heterogeneity, as well as to improve its mechanical and physical performance. In addition, densification may occur during the manufacturing of bamboo products in which hot-pressing processes are used to mold bamboo panels. There are over 1600 publications about bamboo, concentrated in the recent decade, mainly about engineered materials. Although several papers regarding bamboo and wood densification are available, very few studies have comprehensively investigated the densification process solely through compression of natural bamboo culms. According to the literature, applying a combination of compression of 6-12 MPa at temperatures between 120-170 °C for 8-20 min can produce materials with higher strength in comparison to the mechanical properties of natural bamboo. The majority of research on bamboo densification indicates that the modified material results in improved properties in terms of density, hardness, bending strength, stiffness, and durability. This paper provides a review that consolidates knowledge on the concept of bamboo culm densification, discusses the roles of parameters that control the process, ascertains the best practice, and finally determines gaps in this field of knowledge.

Fatigue testing of suture anchors.

In a porcine tibia model, we subjected widely used anchor-suture combinations to a fatigue-testing protocol. The Ethibond No. 2 suture was the weakest part of the anchor-suture combinations when they were loaded to failure by a single pull. Under cyclic-loading conditions, fixation strength was decreased compared with single-pull tests. The suture/anchor interface was identified as the weakest link in the Mitek GII/No. 2 combination and in the Zimmer Statak 3.5/No. 2 combination. In most cases the suture was worn through at the eyelet. Threading the GII anchor with a No. 5 suture and use of larger anchors in combination with No. 2 sutures increased the fatigue strength. Suture breakage at the knot was the predominant failure mode for biodegradable anchors inserted into cortical bone. The highest fatigue strength was seen for the Super Anchor/No. 5 combination when the anchor was inserted in cortical bone. Fatigue testing is crucial for evaluation of suture anchors and should be performed along with single-pull testing. The mechanical performance of a suture anchor threaded with a defined suture depends on several key factors: the pullout strength of the anchor, the tensile strength of the suture, and the interaction of anchor and suture at the eyelet (suture/anchor interface).