RESUMEN
Acetylene hydrogenation is a well-accepted solution to reduce by-products in the ethylene production process, while one of the key technical difficulties lies in developing a catalyst that can provide highly dispersed active sites. In this work, a highly crystalline layered covalent organic framework (COF) material (TbBpy) with excellent thermal stability was synthesized and firstly applied as support for ultrasmall Pd nanoparticles to catalyze acetylene hydrogenation. 100% of C2H2 conversion and 88.2% of C2H4 selectivity can be obtained at 120 °C with the space velocity of 70 000 h-1. The reaction mechanism was elucidated by applying a series of characterization techniques and theoretical calculation. The results indicate that the coordination between Pd and N atom in the bipyridine functional groups of COFs successfully increased the dispersibility and stability of Pd particles, and the introduction of COFs not only improved the adsorption of acetylene and H2 onto catalyst surface, but enhanced the electron transfer process, which can be responsible for the high selectivity and activity of catalyst. This work, for the first time, reported the excellent performance of Pd@TbBpy as a catalyst for acetylene hydrogenation and will facilitate the development and application of COFs materials in the area of petrochemicals.
RESUMEN
BACKGROUND: In this study, a two-step processing method (hydrothermal liquefaction followed by catalytic upgrading) was used to produce upgraded bio-oil. A comprehensive screening analysis of algal species, including four microalgae and four macroalgae, was conducted to bridge the gap between previous accounts of microalgae and macroalgae hydrothermal liquefaction and the upgrading process of the resulting crude bio-oils. RESULTS: Hydrothermal liquefaction using eight algal biomasses was performed at 350 °C for 1 h. The microalgae always produced a higher crude bio-oil yield than the macroalgae due to their high lipid content, among which Schizochytrium limacinum provided the maximum crude bio-oil yield of 54.42 wt%. For microalgae, higher amounts of N in the biomass resulted in higher amounts of N in the crude bio-oil; however, contrary results were observed for the macroalgae. The crude bio-oils generated from both the microalgae and macroalgae were characterized as having a high viscosity, total acid number, and heteroatom content, and they were influenced by the biochemical compositions of the feedstocks. Next, all eight-crude bio-oils were treated at 400 °C for 2 h with 10 wt% Ru/C using tetralin as the hydrogen donor. The hydrogen source was provided after tetralin was transformed to naphthalene. All the upgraded bio-oils had higher energy densities and significantly lower N, O, and S contents and viscosities than their corresponding crude bio-oils. However, the H/C molar ratio of the upgraded bio-oils decreased due to the absence of external hydrogen relative to the crude bio-oils. The S content of the upgraded bio-oil produced from upgrading the Schizochytrium limacinum crude bio-oil was even close to the 50 ppm requirement of China IV diesel. CONCLUSIONS: Microalgae are better feedstocks than macroalgae for liquid fuel production. Biochemical components have a significant impact on the yield and composition of crude bio-oil. Tetralin does not perform as well as external hydrogen for controlling coke formation. The S content of the upgraded bio-oil can be reduced to 76 ppm for the crude bio-oil produced from Schizochytrium limacinum. Upgraded bio-oils have similar properties to those of naphtha and jet fuel.
RESUMEN
In this study, a reutilization of caustic lye during cold caustic extraction (i.e., CCE) process to produce high-purity dissolving pulp and high-concentrated hemicellulose solution was proposed. The results showed that the lye can be reused about 12 times for producing high-purity dissolving pulps. With the number of CCE stages of 12, the hemicellulose in the lye can be auto-concentrated to about 37g/L. The alkali efficiency of the modified CCE process was about 6 (or 3) times better than the traditional CCE process with low- (or middle-) consistency of pulps. Therefore, the present process is feasible to be used for the purification of dissolving pulps with a cost-effective manner.
RESUMEN
Aboveground biomass is an important indicator of grassland community. Direct harvesting has a great damage to the fragile ecosystem. In order to estimate the aboveground biomass of Trifolium repens community more effectively without destroying herbaceous community, various handmade measuring plates were used to study the community height and aboveground biomass of T. repens community in Duzhai Village, Dazhai Town, Yangling Zone, Shaanxi Province. Measuring plates used for trials were made of 17 kinds of specifications of aluminum-plastic and polymer plates. The plate was laid flat on the community crown, the height of plant community from ground level to the plate was measured and recorded, and measurements were repeated 20 times for each specification of plate. Then the plants of whole areal part below the measuring plate were cut to ground level from the corresponding quadrat, and the biomass was obtained after oven-drying and weighing. Finally, the modeling and correlation analysis were made, and the best estimate model was verified. The results showed that multiple regression equations were established with aboveground biomass of corresponding area as dependent variable, and community height below the measuring plate as indepen-dent variable. The independent variable was positively correlated with the dependent variable, and the determination coefficients, R2, ranged from 0.37 to 0.76. Compared with the polymer plates, the aluminum-plastic plates performed better on coefficients of variation of biomass, determination coefficients of regression equations, R2, and degree of accuracy. The best measuring plate was circular aluminum-plastic plate with diameter of 35 cm, and its best regression model was y=1.6460x-3.3462, where the R2 was 0.76 and the prediction accuracy was 92.1%.