Remarkable Improvement in Am3+ and Cm3+ Separation Using a Cooperative Counter Selectivity Strategy by a Combination of Branched Diglycolamides and Hydrophilic Polyaza-heterocycles.

Separation of Am3+ and Cm3+ is one of the most challenging problems in the back-end of the nuclear fuel cycle. In the present work, we exploited the cooperative effect of the opposite selectivity of hydrophobic branched DGA derivatives and hydrophobic N-donor heterocyclic ligands taken in two different phases to achieve improved separation behavior. A systematic study was performed using a series of DGA derivatives to understand the effect and the position of branching in the alkyl chains on the separation behavior of Am3+ and Cm3+. A separation factor (S.F.) value as high as 10 for Cm3+ over Am3+ was obtained in the case of TiBDGA (N,N,N',N'-tetra-iso-butyl diglycolamide) using SO3PhBTPhen ((phenanthroline-2,9-diyl)-1,2,4-triazine-5,5,6,6-tetrayltetrabenzenesulfonic acid) as the aqueous complexant, which is the highest reported value so far for the ligand-based separation of Am3+ and Cm3+ without involving any oxidation or reduction step. The high selectivity favoring Cm3+ ion extraction in the case of this DGA derivative is also explained with the help of computational studies.

A comparative study on the uptake of lanthanides from acidic feeds using extraction chromatography resins containing N,N,N',N'-tetra-n-alkyl diglycolamides with varying alkyl chain lengths in an ionic liquid.

A comparative study on the uptake of several rare earth element (REE) ions viz. La(III), Ce(III), Pr(III), Nd(III), Sm(III), Gd(III) and Dy(III) was carried out from nitric acid feeds using four extraction chromatography resins which contained the diglycolamide (DGA) ligands, N,N,N',N'-tetra-n-alkyldiglycolamide with n-pentyl (TPDGA), n-hexyl (THDGA), n-octyl (TODGA) and n-decyl (TDDGA) groups taken in a room temperature ionic liquid (C4mim·NTf2). The uptake of the lanthanides followed the trend: La(III) < Ce(III) < Pr(III) < Nd(III) < Sm(III) < Gd(III) < Dy(III), which is similar to their ionic potential values and the uptake trend of the resins was TPDGA > THDGA > TODGA > TDDGA. The uptake of the metal ions was very high (>104 g/mL) for all the lanthanide ions and was found to increase with increasing nitric acid concentrations. Based on the encouraging batch data, column studies were carried out with all the four extraction chromatography resins with the lanthanide ions used in this work. The column studies were carried out with both individual lanthanide ions and their mixtures. While the loading studies were carried out with 80 mg/L solutions of the metal ions (with respect to each of those) in the mixture of REEs, the elution studies were carried out using a solution of 0.05 M EDTA in 1 M guanidine carbonate. For the column studies involving individual REEs, 550 mg/L solutions were used. The elution profiles appeared to be sharp as >95% elution of the metal ions was accomplished in only 3 mL of the eluent which amounted to only 1.6 bed volumes which is highly impressive. When the studies were carried out with the mixture of the lanthanide ions, the breakthrough of Dy(III) was last while that of La(III) was seen at much lower volumes which was dependent on the nature of the extractant in the resins.

Radiation stability of two extraction chromatography resin materials containing substituted diglycolamide ligands in an ionic liquid.

The radiation stability of two extraction chromatography resins containing diglycolamide ligands viz. TPDGA (N,N,N',N'-tetra-n-pentyl diglycolamide) and TODGA (N,N,N',N'-tetra-n-octyl diglycolamide) in a room temperature ionic liquid (C4mim.NTf2) was studied by exposing to gamma rays from a 60Co source. The resins were irradiated to varying gamma ray dose up to 1000 kGy where both the dry resins and wet resins (containing a fixed amount nitric acid in contact) were used. The performance assessment of the resins was done by physicochemical characterization as well as uptake studies; both by batch as well as column methods. The physicochemical characterization of the resins was done using FTIR analysis while the surface morphology of the resins was carried out by scanning electron microscopy. The uptake of the metal ions, typically that of Am(III) and Eu(III), representing the trivalent actinides and lanthanides was studied by batch method. The dry resins and those in contact with nitric acid yielded nearly identical results suggesting minimal effect of the radiolytic products of nitric acid on the resin performance. There was negligible change in the Kd values up to an absorbed dose of 300 kGy beyond which there was sharp decrease. However, the Kd values were still quite large even after an absorbed dose of 1000 kGy. The column performance of the irradiated resins was also assessed by the uptake and elution of Eu(III) ion and though loading was affected, the elution behavior was found to have insignificant effect.

Stability of composite polymeric beads containing a calix[4]arene-mono-crown-6 ligand for radio-cesium separation.

Bis-octyloxy-calix[4]arene-mono-crown-6 (BOCMC) is a selective ligand for Cs(I) cation, and has been used in solvent extraction method for its separation from acidic feed. Looking at the various advantages and ease of extraction chromatography separation method, an attempt was made to prepare stable composite beads containing BOCMC entrapped in a suitable polymeric matrix. Therefore, an attempt was made to prepare a series of composite polymeric beads containing BOCMC in polysulfone (PS), polyether sulfone (PES) and sodium alginate polymeric matrix. Preparations of the beads were attempted by dissolving the solid BOCMC in the polymer solution, and also by using the ligand solution in isodecanol/dodecane and ionic liquids and then mixing in the polymeric solution. Every attempt failed to get the desired quality of beads in PES and sodium alginate matrix. However, very good quality and stable beads were obtained when 25 mM ligand solution dissolved in C8mim.Tf2N ionic liquid was used in PS matrix. Detail study for the extraction chromatography separation of Cs(I) was studied with BOCMC/C8mim.Tf2N/PS composite beads. Detail investigations on the preparation, characterization, reusability and radiation stability of these beads have been studied and reported in details.

Highly efficient uptake of Europium (III) and Americium (III) from acidic feeds using extraction chromatography resins containing N,N,N',N'-tetra alkyl diglycolamides with varying alkyl chain length in an ionic liquid.

A comparative study on the uptake of Eu(III) and Am(III) was carried out using four extraction chromatography (XC) resins impregnated with constant weight of the tetra-n-pentyl diglycolamide (TPDGA) ligands, viz. tetra-n-hexyl diglycolamide (THDGA), tetra-n-octyl diglycolamide (TODGA) and tetra-n-decyl diglycolamide (TDDGA) along with C4mim·NTf2, a room temperature ionic liquid (RTIL), from nitric acid feed solutions. The uptake of Eu(III) was higher than that of Am(III) while the uptake trend with the four XC resins followed the order: TPDGA > THDGA > TODGA > TDDGA, which was opposite to the alkyl chain length attached to the DGA extractant. When constant moles of the extractants were used, the observed trend was TODGA > THDGA > TDDGA > TPDGA. Also, for all the four XC resins, the uptake of both Eu(III) and Am(III) ions increased with increasing nitric acid concentration. The uptake data with all the four resins were fitted into different kinetic and isotherm models which conformed to a pseudo-second order kinetics and Langmuir monolayer sorption isotherm. Furthermore, columns were prepared with these XC resins and were used to obtain breakthrough profiles using a feed solution containing 0.55 g/L Eu(III) in 3 M HNO3. Subsequently, the elution of the loaded metal ion from the column was accomplished with a strippant solution containing 1 M guanidine carbonate + 0.05 M EDTA in distilled water. Elution profiles for all the four resins showed sharp peaks with almost no tailing.

Highly efficient uptake of tetravalent actinide ions from nitric acid feeds using an extraction chromatography material containing tetra-n-butyl diglycolamide and a room temperature ionic liquid.

An extraction chromatography (XC) material containing N,N,N',N'-tetra-n-butyl diglycolamide (TBDGA) and 1-butyl-3-methylimidazolium bis(trifluoromethanesulphonyl) imide (C4mim∙NTf2), a room temperature ionic liquid, was used for the uptake of the tetravalent actinide ions Th(IV), Np(IV), and Pu(IV) from nitric acid feed solutions. The uptake of the metal ions followed the trend: Th(IV) < Np(IV) < Pu(IV), which is the same as that of their ionic potential values. While a decrease in the Np(IV) and Pu(IV) uptake was seen with increasing HNO3 concentration at lower acidities, an opposite trend was observed at higher acidities. Th(IV) uptake was not affected with the acid concentration. In view of the very high uptake and its importance in the nuclear fuel cycle, the major part of the studies was carried out with Pu(IV) ion. The loaded Pu(IV) was back extracted from the XC material using a mixture of 0.5 M oxalic acid and 0.5 M nitric acid. The Pu(IV) uptake by the XC material was fitted into different kinetic and isotherm models. The results conformed to the pseudo-second order kinetic model and the Langmuir monolayer sorption model. Column studies were carried out using a feed having 1.6 mg/L Pu solution in 3 M HNO3. While the breakthrough was obtained after passing ca. nine bed volumes, a sharp elution peak was obtained with >99% recovery in about seven bed volumes.

Selective uptake of thorium(IV) from nitric acid medium using two extraction chromatographic resins based on diglycolamide-calix[4]arenes: Application to thorium-uranyl separation in an actual sample.

Two novel extraction chromatography resins (ECRs) containing two diglycolamide (DGA) -functionalized calix[4]arenes with n-propyl and isopentyl substituents at the amide nitrogen atom, termed as ECR-1 and ECR-2, respectively, were evaluated for the uptake of Th(IV) from nitric acid feed solutions. While both the resins were having a quite high Th(IV) uptake ability (Kd >3000 at 3 M HNO3), the uptake was relatively lower with the resin containing the isopentyl DGA, which appeared magnified at lower nitric acid concentrations. Kinetic modeling of the sorption data suggested fitting to the pseudo-second order model pointing to a chemical reaction during the uptake of the metal ion. Sorption isotherm studies were carried out showing a good fitting to the Langmuir and D-R isotherm models, suggesting the uptake conforming to monolayer sorption and a chemisorption model. Glass columns with a bed volume of ca. 2.5 mL containing ca. 0.5 g lots of the ECRs were used for studies to assess the possibility of actual applications of the ECRs. Breakthrough profiles obtained with feed containing 0.7 g/L Th(NO3)3 solution resulted in breakthrough volumes of 8 and 5 mL, respectively, for the ECR-1 and ECR-2 resins. Near quantitative elution of the loaded metal ion was possible using a solution of oxalic acid and nitric acid. A method for the separation of Th-234 from natural uranium was demonstrated for the possible application of ECR-1.

Highly efficient uptake of neptunium from acidic feeds using two solid phase extraction resins containing diglycolamide-functionalized calix[4]arene ligands.

Two solid phase extraction resins (SPER) were prepared by impregnating solutions of two diglycolamide-functionalized calix[4]arenes in 10% isodecanol in n-dodecane into Chromosorb W, as the stationary phase. While SPER-I contained n-propyl functionalized calix[4]arene, SPER-II contained the calix[4]arene with isopentyl groups at the carboxamide nitrogen atoms. The SPERs were characterized by SEM, TGA, FTIR, etc. and were used for the batch uptake of neptunium(IV) from nitric acid feed solutions. While the uptake of Np(IV) was extremely high with SPER-I (Kd: 47,544 at 3 M nitric acid, ca. 8% extractant loading), SPER-II displayed a significantly lower extraction efficiency (Kd: 13,724 under identical conditions) as indicated by the batch uptake studies. Sorption isotherm studies were carried out which indicated good fitting to the Langmuir model suggesting uptake conforming to monolayer sorption. Fitting to the D-R isotherm model conformed to a chemisorption model. Column studies were also carried out and the elution profiles, obtained with solutions of oxalic acid and nitric acid indicated very sharp peaks suggesting that the column can be used for the separation of Np(IV) from acidic radioactive feeds.

Comparative uptake studies on trivalent f-cations from acidic feeds using two extraction chromatography resins containing a diglycolamide in molecular diluent and ionic liquid.

Low molecular weight diglycolamide (DGA) extractants were tested for the extraction of europium(III) and americium(III) from nitric acid solutions in n-dodecane, a molecular diluent and 1-butyl-3-methylimidazolium bis(trifluoromethanesulphonyl) imide (C4mim⋅NTf2), a room temperature ionic liquid, as the diluents. N,N,N',N'-tetra-n-butyl diglycolamide (TBDGA) was selected for extraction chromatography (XC) studies involving Eu(III) and Am(III). While the TBDGA resin containing n-dodecane gave reasonably high Kd values, that containing the ionic liquid showed higher Eu(III) uptake values. Compared to Eu(III), Am(III) was extracted by the resins to a lower extent. The loaded Eu(III) was back extracted from the resin using 0.05 M EDTA solutions in a buffered medium containing 1 M guanidine carbonate. Reusability studies indicated that, while the ionic liquid-based resin can be conveniently recycled five times with very marginal decrease in the percentage extraction values, there was a sharp decrease in the percent extraction after three cycles with the n-dodecane-based resin. The uptake data was fitted into different isotherm models and the results conformed to the Langmuir model. Based on the batch uptake studies, columns were prepared and the breakthrough as well as elution profiles were obtained. The elution profiles were found to be sharp without any significant tailing.

Actinide ion uptake from acidic radioactive feeds using an extraction chromatographic resin containing a branched dialkyl amide.

A dialkyl amide with branched alkyl group, viz. N,N-di(2-ethylhexyl)-propionamide (D2EHPrA) was used as the organic extractant in an extraction chromatographic resin prepared for the first time and evaluated for the separation of uranium from acidic feeds. The distribution coefficient measurements, carried out at varying HNO3 concentrations, indicated an increase in the UO22+ ion sorption with increasing nitric acid concentration. The UO22+ ion sorption kinetics and sorption isotherms with this resin were investigated in details. The column studies indicated that 8.3 mg of uranium could be loaded on a 2.1 cm3 column bed volume containing 0.35 g resin. Batch distribution data for other actinides such as Np4+ and Pu4+ indicated that the resin can also be used for effective separation of these metal ions from acidic feeds. Though the resin showed effectiveness for Np and Pu, detailed investigations dealing with macro concentrations of metal ions (in gm quantities) were restricted to uranium only due to hazardous nature of plutonium and limited availability of neptunium. The encouraging results reported in this work is an indication of the possible application of this resin for the recovery or pre-concentration of UO22+, Np4+ and Pu4+ ions from large volumes of aqueous solutions of moderate acidity.

Two novel extraction chromatographic resins containing benzene-centered tripodal diglycolamide ligands: Actinide uptake, kinetic modeling and isotherm studies.

Two novel extraction chromatographic resins (EC), termed as RL-1 and RL-2, were prepared by impregnating two benzene-centered tripodal iglycolamide ligands (Bz-T-DGA) containing different spacer groups where the ligands are termed as L-1 and L-2, respectively. They were employed for the uptake of actinide and fission product ions, viz. Am3+, Eu3+, UO22+, Np4+, Pu4+, Sr2+, and Cs+, from acidic feeds. Weight distribution coefficient (Kd) values were measured by the batch method and the loaded metal ions were back extracted using a 0.01 M EDTA solution at pH 4. Kinetic modeling of the sorption data of Am(III) on both resins suggested pseudo-second order rate kinetics with rate constants of 1.68 × 10-6 and 2.47 × 10-6 g/cpm.min for the resins containing L-1 and L-2, respectively. Sorption isotherm studies indicated the Langmuir monolayer chemisorption phenomenon with Eu(III) experimentally determined saturation uptake capacities of 6.02 ± 0.11 and 5.49 ± 0.14 mg per g of RL-1 and RL-2 resins, respectively. As the batch uptake study results appeared encouraging, column studies were also carried out using both resins. The resin reusability data indicated a marginal change in the Kd values for the RL-1 resin up to three repeat runs beyond which a steady decrease of the Kd value was seen. On the other hand, in the case of RL-2 a steady decrease in the Kd values was observed for three repeat runs beyond which there was marginal change.

Superparamagnetic graphene oxide-magnetite nanoparticle composites for uptake of actinide ions from mildly acidic feeds.

Super paramagnetic graphene oxide (GO) - Fe3O4 nanoparticle composites were prepared and characterized by conventional techniques such as XRD, SEM, EDX, FT-IR, Raman, XPS, DLS and zeta potential, etc. TEM studies have confirmed nanoparticle nature of the composites. The GO-magnetic nanoparticle composites can be dispersed in mildly acidic aqueous solutions and get concentrated in a small volume under application of an external magnetic field. The composites were evaluated for the uptake of actinide ions such as Am3+, UO22+, Th4+ and Pu4+ from mildly acidic aqueous solutions. Am3+ sorption sharply increased with pH as the Kd values increased from about 10 at pH 1 to 105 at pH 3 beyond which a plateau in the Kd values was seen. Eu3+ displayed nearly comparable uptake behaviour to that of Am3+ while the uptake of other metal ions followed the trend: Pu(IV)>Th(IV)>>UO22+. The adsorption behaviour of Am3+ onto the graphene oxide - Fe3O4 nanoparticle composites fitted very well to the Langmuir as well as Temkin isotherm models. The desorption rate (using 1M HNO3) was fast and reusability study results were highly encouraging. The very high uptake values suggest possible application of the magnetic nanoparticles in radioactive waste remediation in natural ground water.