Bright white light emission from lanthanide oxide LaGdO3 for LED lighting by Bi3+ to Eu3+ energy transfer.

Phosphors with intrinsic white light emission are of great potential in constructing high-quality white LEDs (WLEDs). In this work, we propose the use of energy transfer from Bi3+ to Eu3+ ions for white light emission. A unique Bi3+-activated phosphor LaGdO3 (LGO):Bi3+ was generated using the conventional high-temperature solid-state process. An energy transfer was established by introducing Eu3+ into the phosphor composition. The emission colour of LGO:Bi3+,Eu3+ phosphors changes from cyan to white to orange-red depending on the Bi3+/Eu3+ doping proportion. The energy transfer between the Bi3+ and Eu3+ ions results from the dipole-dipole interaction. The LGO:Bi3+,Eu3+ phosphors were combined with a near-ultraviolet chip to successfully create a single-component WLED device with a colour-rendering index of 92.4. Our work demonstrates the energy transfer as a route for single-component white light emission and makes LGO:Bi3+,Eu3+ phosphors one of the candidate materials for near-ultraviolet lighting.

Facile Approach for Metallic Precursor Engineering for Efficient Kesterite Thin-Film Solar Cells.

Kesterite-based Cu2ZnSn(S,Se)4 (CZTSSe) thin-film solar cells (TFSCs) are a promising candidate for low-cost, clean energy production owing to their environmental friendliness and the earth-abundant nature of their constituents. However, the advancement of kesterite TFSCs has been impeded by abundant defects and poor microstructure, limiting their performance potential. In this study, we present efficient Ag-alloyed CZTSSe TFSCs enabled by a facile metallic precursor engineering approach. The positioning of the Ag nanolayer in the metallic stacked precursor proves crucial in expediting the formation of Cu-Sn metal alloys during the alloying process. Specifically, Ag-included metallic precursors promote the growth of larger grains and a denser microstructure in CZTSSe thin films compared to those without Ag. Moreover, the improved uniformity of Ag, facilitated by the evaporation deposition technique, significantly suppresses the formation of detrimental defects and related defect clusters. This suppression effectively reduces nonradiative recombination, resulting in enhanced performance in kesterite TFSCs. This study not only introduces a metallic precursor engineering strategy for efficient kesterite-based TFSCs but also accelerates the development of microstructure evolution from metallic stacked precursors to metal chalcogenide compounds.

Enhanced Mono/Divalent Ion Separation via Charged Interlayer Channels in Montmorillonite-Based Membranes.

Efficient mono- and divalent ion separation is pivotal for environmental conservation and energy utilization. Two-dimensional (2D) materials featuring interlayer nanochannels exhibit unique water and ion transport properties, rendering them highly suitable for water treatment membranes. In this work, we incorporated polydopamine/polyethylenimine (PDA/PEI) copolymers into 2D montmorillonite (MMT) nanosheet interlayer channels through electrostatic interactions and bioinspired bonding. A modified laminar structure was formed on the substrate surface via a straightforward vacuum filtration. The electrodialysis experiments reveal that these membranes could achieve monovalent permselectivity of 11.06 and Na+ flux of 2.09 × 10-8 mol cm-2 s-1. The enhanced permselectivity results from the synergistic effect of electrostatic and steric hindrance effect. In addition, the interaction between the PDA/PEI copolymer and the MMT nanosheet ensures the long-term operational stability of the membranes. Theoretical simulations reveal that Na+ has a lower migration energy barrier and higher migration rate for the modified MMT-based membrane compared to Mg2+. This work presents a novel approach for the development of monovalent permselective membranes.

Unveiling the Role of Ge in CZTSSe Solar Cells by Advanced Micro-To-Atom Scale Characterizations.

Kesterite is an earth-abundant energy material with high predicted power conversion efficiency, making it a sustainable and promising option for photovoltaics. However, a large open circuit voltage Voc deficit due to non-radiative recombination at intrinsic defects remains a major hurdle, limiting device performance. Incorporating Ge into the kesterite structure emerges as an effective approach for enhancing performance by manipulating defects and morphology. Herein, how different amounts of Ge affect the kesterite growth pathways through the combination of advanced microscopy characterization techniques are systematically investigated. The results demonstrate the significance of incorporating Ge during the selenization process of the CZTSSe thin film. At high temperature, the Ge incorporation effectively delays the selenization process due to the formation of a ZnSe layer on top of the metal alloys through decomposition of the Cu-Zn alloy and formation of Cu-Sn alloy, subsequently forming of Cu-Sn-Se phase. Such an effect is compounded by more Ge incorporation that further postpones kesterite formation. Furthermore, introducing Ge mitigates detrimental "horizontal" grain boundaries by increasing the grain size on upper layer. The Ge incorporation strategy discussed in this study holds great promise for improving device performance and grain quality in CZTSSe and other polycrystalline chalcogenide solar cells.

The Intermediate Connection of Subcells in Si-based Tandem Solar Cells.

Tandem solar cells are rationally designed and fabricated by stacking multiple subcells to achieve power conversion efficiency well above the Shockley-Queisser (SQ) limit. There is a large selection pool for the subcell candidates, such as Si, III-V, Kesterite, Perovskite, and organic solar cells. A series of different combinations of these subcells have been successfully demonstrated in practical tandem solar cell devices. However, there has not been a systematic summary of how to connect subcells in a tandem solar cell using a practical, cost-effective, and efficiency-beneficial fashion. In this work, the connection manners of subcells within a tandem cell are classified into three main categories, performing sequential growth, using the physical connection, and applying an intermediate layer, focusing on systematical description of intermediate layers using different materials. The advantages and disadvantages of these connection methods and their applicability to tandem cell types are further elaborated using two typical example models, III-V/Si and Perovskite inclusive tandem cell devices. Eventually, this work can provide useful guidance on how to carry out a suitable intermediate connection in the design of tandem solar cells depending on the selected subcells and device structure.

Cd-Free Pure Sulfide Kesterite Cu2 ZnSnS4 Solar Cell with Over 800 mV Open-Circuit Voltage Enabled by Phase Evolution Intervention.

The Cd-free Cu2 ZnSnS4 (CZTS) solar cell is an ideal candidate for producing low-cost clean energy through green materials owing to its inherent environmental friendliness and earth abundance. Nevertheless, sulfide CZTS has long suffered from severe open-circuit voltage (VOC ) deficits, limiting the full exploitation of performance potential and further progress. Here, an effective strategy is proposed to alleviate the nonradiative VOC loss by manipulating the phase evolution during the critical kesterite phase formation stage. With a Ge cap layer on the precursor, premature CZTS grain formation is suppressed at low temperatures, leading to fewer nucleation centers at the initial crystallization stage. Consequently, the CZTS grain formation and crystallization are deferred to high temperatures, resulting in enhanced grain interior quality and less unfavorable grain boundaries in the final film. As a result, a champion efficiency of 10.7% for Cd-free CZTS solar cells with remarkably high VOC beyond 800 mV (63.2% Schockley-Queisser limit) is realized, indicating that nonradiative recombination is effectively inhibited. This strategy may advance other compound semiconductors seeking high-quality crystallization.

Opinion Mining by Convolutional Neural Networks for Maximizing Discoverability of Nanomaterials.

The scientific literature contains valuable information that can be used for future applications, but manual analysis presents challenges due to its size and disciplinary boundaries. The prevailing solution involves natural language processing (NLP) techniques such as information retrieval. Nonetheless, existing automated systems primarily provide either statistically based shallow information or deep information without traceability, thereby falling short of delivering high-quality and reliable insights. To address this, we propose an innovative approach of leveraging sentiment information embedded within the literature to track the opinions toward materials. In this study, we integrated material knowledge into text representation and constructed opinion data sets to hierarchically train deep learning models, named as Scientific Sentiment Network (SSNet). SSNet can effectively extract knowledge from the energy material literature and accurately categorize expert opinions into challenges and opportunities (94% and 92% accuracy, respectively). By incorporating sentiment features determined by SSNet, we can predict the ranking of emerging thermoelectric materials with a 70% correlation to experimental outcomes. Furthermore, our model achieves a commendable 68% accuracy in predicting suitable nanomaterials for atomic layer deposition (ALD) over time. These promising results offer a practical framework to extract and synthesize knowledge from the scientific literature, thereby accelerating research in the field of nanomaterials.

Energy transfer and tunable emission in BaSrGd4O8:Bi3+,Eu3+ phosphors for warm WLED.

In this work, a series of BaSrGd4O8:xBi3+ blue phosphors was synthesized employing the high-temperature solid-state method. Phase purity of the samples was verified by X-ray diffraction and Rietveld refinement. Time-resolved photoluminescence spectra revealed the existence of two distinct Bi sites. Subsequent optimization of dopant types and doping levels in the batch led to an almost twofold increase in quantum efficiency. The introduction of Eu3+ into the phosphors facilitated the construction of an energy transfer pathway. As the concentration of Eu3+ was increased, the emission color changed from blue to purple and finally to red. In addition, the thermal stability and potential applications of the phosphors were extensively investigated. Finally, two WLED devices were successfully fabricated with color rendering indices of 96.27 and 92.18, and correlated color temperatures of 5198 and 2475 K. This underscores the prospective application of these phosphors in the field of high-quality warm WLEDs.

Graphitic carbon nitride membranes intercalated with nano-sized Fe-MOF for enhanced water purification via synergistic separation and Fenton-like processes.

Versatile two-dimensional nanomaterials have offered a promising prospect to enhance the water purification efficiency and overcome the fouling obstacle in membrane technology. In this work, a graphitic carbon nitride (g-C3N4) nanosheet membrane intercalated with the nano-sized Fe-based metal-organic framework (MIL-100(Fe)) is developed for the enhanced removal of aqueous organic contaminants by synergically promoting separation and Fenton-like processes. The g-C3N4/MIL-100(Fe) membrane is constructed through a self-assembly route in which the nano-MIL-100(Fe) is anchored into g-C3N4 layers by the coordination bonds between Fe nodes and pyridinic N. The MIL-100(Fe) intercalation not only enlarges the interlayer spacing to raise the membrane permeability, but also expedites the electron transfer between Fe2+ and Fe3+ to improve the Fenton-like activity. With a stable water flux of 98.2 L m2·h-1·bar-1 under wide-range pH and pressures, the g-C3N4/MIL-100(Fe) membrane shows high dye removal efficiency (≥99%) and prominent self-cleaning ability. Mechanism insight proposes a combination of size exclusion, electrostatic interaction and steady radical generation. The intercalation of nano-MIL-100(Fe) into g-C3N4 membranes can realize the mutual promotion between separation and Fenton-like processes, the synergistic effect of which provides an effective and feasible strategy for aqueous pollution abatement.

Warming reduced flowering synchrony and extended community flowering season in an alpine meadow on the Tibetan Plateau.

The timing of phenological events is highly sensitive to climate change, and may influence ecosystem structure and function. Although changes in flowering phenology among species under climate change have been reported widely, how species-specific shifts will affect phenological synchrony and community-level phenology patterns remains unclear. We conducted a manipulative experiment of warming and precipitation addition and reduction to explore how climate change affected flowering phenology at the species and community levels in an alpine meadow on the eastern Tibetan Plateau. We found that warming advanced the first and last flowering times differently and with no consistent shifts in flowering duration among species, resulting in the entire flowering period of species emerging earlier in the growing season. Early-flowering species were more sensitive to warming than mid- and late-flowering species, thereby reducing flowering synchrony among species and extending the community-level flowering season. However, precipitation and its interactions with warming had no significant effects on flowering phenology. Our results suggest that temperature regulates flowering phenology from the species to community levels in this alpine meadow community, yet how species shifted their flowering timing and duration in response to warming varied. This species-level divergence may reshape flowering phenology in this alpine plant community. Decreasing flowering synchrony among species and the extension of community-level flowering seasons under warming may alter future trophic interactions, with cascading consequences to community and ecosystem function.

10.3% Efficient Green Cd-Free Cu2 ZnSnS4 Solar Cells Enabled by Liquid-Phase Promoted Grain Growth.

Small grain size and near-horizontal grain boundaries are known to be detrimental to the carrier collection efficiency and device performance of pure-sulfide Cu2 ZnSnS4 (CZTS) solar cells. However, forming large grains spanning the absorber layer while maintaining high electronic quality is challenging particularly for pure sulfide CZTS. Herein, a liquid-phase-assisted grain growth (LGG) model that enables the formation of large grains spanning across the CZTS absorber without compromising the electronic quality is demonstrated. By introducing a Ge-alloyed CZTS nanoparticle layer at the bottom of the sputtered precursor, a Cu-rich and Sn-rich liquid phase forms at the high temperature sulfurization stage, which can effectively remove the detrimental near-horizontal grain boundaries and promote grain growth, thus greatly improving the carrier collection efficiency and reducing nonradiative recombination. The remaining liquid phase layer at the rear interface shows a high work function, acting as an effective hole transport layer. The modified morphology greatly increases the short-circuit current density and fill factor, enabling 10.3% efficient green Cd-free CZTS devices. This work unlocks a grain growth mechanism, advancing the morphology control of sulfide-based kesterite solar cells.

The Influence of Climate Change on Droughts and Floods in the Yangtze River Basin from 2003 to 2020.

In recent decades, extreme floods and droughts have occurred frequently around the world, which seriously threatens the social and economic development and the safety of people's lives and properties. Therefore, it is of great scientific significance to discuss the causes and characteristic quantization of extreme floods and droughts. Here, the terrestrial water storage change (TWSC) derived from the Gravity Recovery and Climate Experiment (GRACE) and its Follow-On (GRACE-FO) data was used to characterize the floods and droughts in the Yangtze River basin (YRB) during 2003 and 2020. To reduce the uncertainty of TWSC results, the generalized three-cornered hat and least square methods were used to fuse TWSC results from six GRACE solutions. Then combining precipitation (PPT), evapotranspiration, soil moisture (SM), runoff, and extreme climate index data, the influence of climate change on floods and droughts in the YRB was discussed and analyzed. The results show that the fused method can effectively improve the uncertainty of TWSC results. And seven droughts and seven floods occurred in the upper of YRB (UY) and nine droughts and six floods appeared in the middle and lower of YRB (MLY) during the study period. The correlation between TWSC and PPT (0.33) is the strongest in the UY, and the response time between the two is 1 month, while TWSC and SM (0.67) are strongly correlated with no delay in the MLY. The reason for this difference is mainly due to the large-scale hydropower development in the UY. Floods and droughts in the UY and MLY are more influenced by the El Niño-Southern Oscillation (ENSO) (correlation coefficients are 0.39 and 0.50, respectively) than the Indian Ocean Dipole (IOD) (correlation coefficients are 0.19 and 0.09, respectively). The IOD event is usually accompanied by the ENSO event (the probability is 80%), and the hydrological hazards caused by independent ENSO events are less severe than those caused by these two extreme climate events in the YRB. Our results provide a reference for the study on the formation, development, and recovery mechanism of regional floods and droughts on a global scale.

The gC1qR Binding Site Mutant PCV2 Is a Potential Vaccine Strain That Does Not Impair Memory CD4+ T-Cell Generation by Vaccines.

PCV2 has been reported to reduce the protective effects of various vaccines on immunized pigs. Our previous studies showed that the interaction of Cap and host protein gC1qR mediated the PCV2 infection-induced suppression of immune response. Thus, we wondered whether the gC1qR binding site mutant PCV2RmA could be a vaccine strain and whether this mutant PCV2RmA impairs other vaccines. Herein, we showed that PCV2 infection reduced the classic swine fever virus (CSFV) vaccine-induced generation of memory CD4+ T cells through the interaction of Cap with gC1qR. PCV2RmA can effectively induce the production of PCV2-specific antibodies, neutralizing antibodies, and peripheral blood lymphocyte proliferation in piglets at the same levels as the commercial inactivated PCV2 vaccine. The PCV2RmA-induced anti-PCV2 immune responses could eliminate the serum virus and would not lead to pathological lesions like wild-type PCV2. Moreover, compared to the commercial inactivated PCV2 vaccine, PCV2RmA is capable of inducing more durable protective immunity against PCV2 that induced production of PCV2-specific antibodies and neutralizing antibodies for a longer time via stronger induction of memory CD4+ T cells. Importantly, PCV2RmA infection did not impair the CSFV vaccine-induced generation of memory CD4+ T cells. Collectively, our findings showed that PCV2 infection impairs memory CD4+ T-cell generation to affect vaccination and provide evidence for the use of PCV2RmA as an efficient vaccine to prevent PCV2 infection. IMPORTANCE PCV2 is one of the costliest pathogens in pigs worldwide. Usage of PCV2 vaccines can prevent the PCV2 infection-induced clinical syndromes but not the viral spread. Our previous work found that PCV2 infection suppresses the host type I interferon innate immune response and CD4+ T-cell-mediated Th1 immune response through the interaction of Cap with host gC1qR. Here, we showed that the gC1qR binding site mutant PCV2RmA could effectively induce anti-PCV2 immunity and provide more durable protective immunity against wild-type PCV2 infection in pigs. PCV2RmA would not impair the generation of memory CD4+ T cells induced by classic swine fever virus (CSFV) vaccines as wild-type PCV2 did. Therefore, PCV2RmA can serve as a potential vaccine strain to better protect pigs against PCV2 infection.

Large-Grain Spanning Monolayer Cu2 ZnSnSe4 Thin-Film Solar Cells Grown from Metal Precursor.

The persistent double layer structure whereby two layers with different properties form at the front and rear of absorbers is a critical challenge in the field of kesterite thin-film solar cells, which imposes additional nonradiative recombination in the quasi-neutral region and potential limitation to the transport of hole carriers. Herein, an effective model for growing monolayer CZTSe thin-films based on metal precursors with large grains spanning the whole film is developed. Voids and fine grain layer are avoided successfully by suppressing the formation of a Sn-rich liquid metal phase near Mo back contact during alloying, while grain coarsening is greatly promoted by enhancing mass transfer during grain growth. The desired morphology exhibits several encouraging features, including significantly reduced recombination in the quasi-neutral region that contributes to the large increase of short-circuit current, and a quasi-Ohmic back contact which is a prerequisite for high fill factor. Though this growth mode may introduce more interfacial defects which require further modification, the strategies demonstrated remove a primary obstacle toward higher efficiency kesterite solar cells, and can be applicable to morphology control with other emerging chalcogenide thin films.

Kesterite Solar Cells: Insights into Current Strategies and Challenges.

Earth-abundant and environmentally benign kesterite Cu2ZnSn(S,Se)4 (CZTSSe) is a promising alternative to its cousin chalcopyrite Cu(In,Ga)(S,Se)2 (CIGS) for photovoltaic applications. However, the power conversion efficiency of CZTSSe solar cells has been stagnant at 12.6% for years, still far lower than that of CIGS (23.35%). In this report, insights into the latest cutting-edge strategies for further advance in the performance of kesterite solar cells is provided, particularly focusing on the postdeposition thermal treatment (for bare absorber, heterojunction, and completed device), alkali doping, and bandgap grading by engineering graded cation and/or anion alloying. These strategies, which have led to the step-change improvements in the power conversion efficiency of the counterpart CIGS solar cells, are also the most promising ones to achieve further efficiency breakthroughs for kesterite solar cells. Herein, the recent advances in kesterite solar cells along these pathways are reviewed, and more importantly, a comprehensive understanding of the underlying mechanisms is provided, and promising directions for the ongoing development of kesterite solar cells are proposed.

A Facile Process for Partial Ag Substitution in Kesterite Cu2ZnSn(S,Se)4 Solar Cells Enabling a Device Efficiency of over 12.

A cation substitution in Cu2ZnSn(S,Se)4 (CZTSSe) offers a viable strategy to reduce the open-circuit voltage (Voc)-deficit by altering the characteristics of band-tail states, antisite defects, and related defect clusters. Herein, we report a facile single process, i.e., simply introducing a thin Ag layer on a metallic precursor, to effectively improve the device characteristics and performances in kesterite (Agx,Cu1-x)2ZnSn(Sy,Se1-y)4 (ACZTSSe) solar cells. Probing into the relationship between the external quantum efficiency derivative (dEQE/dλ) and device performances revealed the Voc-deficit characteristics in the ACZTSSe solar cells as a function of Cu and Ag contents. The fabricated champion ACZTSSe solar cell device showed an efficiency of 12.07% and a record low Voc-deficit of 561 mV. Thorough investigations into the mechanism underpinning the improved performance in the ACZTSSe device further revealed the improved band-tailing characteristic, effective minority carrier lifetime, and diode factors as well as reduced antisite defects and related defect clusters as compared to the CZTSSe device. This study demonstrates the feasibility of effectively suppressing antisite defects, related defect clusters, and band-tailing characteristics by simply introducing a thin Ag layer on a metallic precursor in the kesterite solar cells, which in turn effectively reduces the Voc-deficit.

Efficient removal of halogenated phenols by vacuum-UV system through combined photolysis and OH oxidation: Efficiency, mechanism and economic analysis.

In this study, efficient simultaneous degradation and dechlorination of the photo-recalcitrant emerging disinfection byproduct, 2-chlorophenol (2-CP), was achieved by vacuum-ultraviolet (VUV) system for the first time. Different from the conventional UV system, the combined action of direct photolysis and OH oxidation in VUV system led to a significantly higher removal efficiency for 2-CP. In UV system, 2-CP degradation rate constants was independent of the initial 2-CP concentration, and was increased with enhancing pH. To the contrary, in VUV system, higher initial concentration of 2-CP resulted in lower rate constant, and the degradation rates of 2-CP under both acidic and alkaline conditions were higher than that at the neutral pH. Moreover, humic acid could inhibit 2-CP degradation more prominently in VUV system than in UV system, owing to the scavenging effect of OH by it. The degradation pathways of 2-CP were proposed based on the identified main degradation products by GC-MS/MS. Furthermore, degradation of the other seven typical halogenated phenols by VUV irradiation in tap water, ultrafiltrated water and Mill-Q water were investigated to verify the feasibility of the system. Based on the systematic economic analysis, VUV process is economically feasible for the advanced treatment of tap water to remove halogenated phenols.

Burn-In Degradation Mechanism Identified for Small Molecular Acceptor-Based High-Efficiency Nonfullerene Organic Solar Cells.

Organic solar cells (OSCs) have again become a hot research topic in recent years. The record power conversion efficiency (PCE) of OSCs has boosted to over 17% in 2020. Apart from the high PCE, the stability of OSCs is also critical for their future applications and commercialization. Recently, many studies have proposed that burn-in degradation can be considered as an ineluctable barrier to long-term stable OSCs. However, there is still lack of studies to explain the detailed mechanism of this burn-in process. In this work, we first investigated the mechanism of the burn-in process in the high-efficiency PM6:N3-based nonfullerene OSCs. The PM6:N3-based device achieved a profound average PCE of 14.10% but also showed a significant performance loss after the burn-in degradation. Following characterizations such as dark J-V, photoluminescence (PL), time-resolved PL, Urbach energy estimation, and electrochemical impedance spectroscopy reveal that the burn-in degradation observed is closely related to the current extraction, energy transfer, nonradiative recombination, and charge transport process in the PM6:N3-based device. At the same time, it has small effects on the exciton dissociation process and energetic disorder in the PM6:N3-based device. Atomic force microscopy, scanning electron microscopy, transmission electron microscopy, and grazing incidence X-ray diffraction measurements gratifyingly found that the morphology of the PM6:N3 active layer is relatively stable during the burn-in degradation. Therefore, these observed degradations are suspected results from the instability of interfaces and electrodes. The atoms in carrier transport layers and electrodes may diffuse to the active layer during the degradation, which changes the energy levels of each layer and causes traps at the interface and in the active layer. Conquering the instability of interfaces and electrodes is proposed as the prior task for PM6:N3-based OSCs to achieve long-term stability. Our study provides insights into the mechanism behind the burn-in degradation of the PM6:N3-based OSCs, which takes the first step to conquer this barrier.

Thermo-Sensitive Dual-Functional Nanospheres with Enhanced Lubrication and Drug Delivery for the Treatment of Osteoarthritis.

Osteoarthritis is a typical degenerative joint disease related to a lubrication deficiency of articular cartilage, which is characterized by increased friction at the joint surface and severe inflammation of the joint capsule. Consequently, therapies combining lubrication restoration and drug intervention are regarded as a promising strategy for the treatment of osteoarthritis. In the present study, thermo-sensitive dual-functional nanospheres, poly[N-isopropylacrylamide-2-methacryloyloxyethyl phosphorylcholine] (PNIPAM-PMPC), are developed through emulsion polymerization. The PNIPAM-PMPC nanospheres could enhance lubrication based on the hydration lubrication mechanism by forming a tenacious hydration layer surrounding the zwitterionic headgroups, and achieve local drug delivery by encapsulating the anti-inflammatory drug diclofenac sodium. The lubrication and drug release tests showed improved lubrication and thermo-sensitive drug release of the nanospheres. The in vitro test using cytokines-treated chondrocytes indicated that the PNIPAM-PMPC nanospheres were biocompatible and upregulated anabolic genes and simultaneously downregulated catabolic genes of the articular cartilage. In summary, the developed PNIPAM-PMPC nanospheres, with the property of enhanced lubrication and local drug delivery, can be an effective nanomedicine for the treatment of osteoarthritis.

Author Correction: Metal-coordinated sub-10 nm membranes for water purification.

An amendment to this paper has been published and can be accessed via a link at the top of the paper.