RESUMEN
This retrospective study assessed outcomes and complications related to implants and prostheses in edentulous patients treated with soft-milled cobalt-chromium-ceramic full-arch screw-retained implant-supported prostheses (SCCSIPs). After the final prosthesis was delivered, patients participated in an annual dental check-up program, including clinical and radiographic assessments. Outcomes of implants and prostheses were evaluated, and biological and technical complications were categorized as major or minor. Implant and prosthesis cumulative survival rates were assessed using the life table analysis. A total of twenty-five participants (mean age 63.6 ± 7.3 years) with 33 SCCSIPs were observed for a mean of 68.9 ± 27.9 months (range 1-10 years). A total of 7 out of 245 implants were lost, with no effect on prosthesis survival, leading to cumulative survival rates of 97.1% for implants and 100% for prostheses. The most recurrent minor and major biological complications were soft tissue recession (9%) and late implant failure (2.8%). Among 25 technical complications, porcelain fracture was the only major technical complication, requiring prosthesis removal (1%). Porcelain chipping was the most frequent minor technical complication, affecting 21 crowns (5.4%), which required polishing only. At the end of the follow-up, 69.7% of the prostheses were free of technical complications. Within the limitations of this study, SCCSIP showed promising clinical performance after 1-10 years.
RESUMEN
AIM: The aim of this paper is to perform a retrospective assessment of the clinical performance of the complete oral rehabilitation of patients with bruxism treated with implants and teeth-supported veneered and non-veneered monolithic zirconia restorations with increased occlusal vertical dimension. METHODS: In this retrospective follow-up study, 16 bruxer patients, mean age 59.5 ± 14.9 years, were treated with 152 veneered and 229 non-veneered monolithic zirconia and followed for a mean of 58.8 ± 18.8 months (range 1-8 years). The patients were examined clinically and radiographically, annually. Clinical data were extracted from the medical records. In the recall appointments, modified California Dental Association (CDA) criteria were used to evaluate the restorations. Implant and restoration survival and success rates were recorded and analyzed. RESULTS: The cumulative survival rates of implants and restorations were 97.7% and 97.6%, respectively. Nine restorations were replaced: three due to horizontal tooth fractures, two because of implant failure and four had secondary caries. A total of 43 biologic and technical complications were recorded. In the veneered group, the predominant complication was minor veneer chipping (16.4%), which required polishing only (grade 1). In the non-veneered group, the main complication was open proximal contacts between the implant restorations and adjacent teeth (14.5%). CONCLUSIONS: The survival rates of restorations and implants in patients with bruxism are excellent, even though veneered zirconia restoration exhibited a high rate of minor veneer chipping, which required polishing only. The biologic complication of fractured single-tooth abutment may occur.
RESUMEN
The aim of this study was to assess retrospectively the survival and success rates of monolithic zirconia restorations supported by teeth and implants in bruxer versus non-bruxer patients. Methods: A total of 15 bruxer and 25 non-bruxer patients attended the recall appointment. The bruxer group (mean age of 61.2 ± 13.3 years and follow-up of 58.7 ± 16.8 months) were treated with 331 monolithic zirconia restorations, while the non-bruxer group, with a comparable mean age and follow-up time, were treated with 306 monolithic zirconia restorations. Clinical data were retrieved from the patients' files. At the recall appointment, all supporting teeth and implants were examined for biological and technical complications, and the restorations were evaluated using modified California Dental Association (CDA) criteria. Data were statistically analyzed using survival analysis methods. A significance level of p < 0.05 was used. A total of 31 versus 27 biologic and technical complications were recorded in the bruxer and non-bruxer groups, respectively. No significant differences were found between the two groups regarding overall complications and survival rate. Regarding the type of complication, a significantly higher rate of veneered porcelain chipping (p = 0.045) was observed in the bruxer group. With regard to biological complications, the only complications that exhibited a borderline, although not significant, difference were three fractured teeth exclusively in the bruxer group (p = 0.051), which were replaced with implant-supported restorations. Within the limitations of this study, we conclude that there were no significant differences in the overall survival and success rates of the monolithic zirconia restorations in bruxer versus non-bruxer patients, although veneered zirconia restorations and single tooth abutments exhibited a higher rate of complications in the bruxer group.
RESUMEN
The static and dynamic load-bearing capacities and failure modes of zirconia crowns screwed to multi-unit abutments (MUAs) with and without a titanium base (T-base) were determined. Thirty-six monolithic zirconia crowns screwed to straight MUAs torqued to laboratory analogs (30 Ncm) were assigned to two groups (n = 18). In group A, the zirconia crowns were screwed directly to the MUAs; in group B, the zirconia crowns were cemented to the T-base and screwed to the MUAs. All specimens were aged in 100% humidity (37 °C) for one month and subjected to thermocycling (20,000 cycles). Afterwards, the specimens underwent static and dynamic loading tests following ISO 14801. The failure modes were evaluated by stereomicroscopy (20×). There was an unequivocally similar trend in the S-N plots of both specimen groups. The load at which the specimens survived 5,000,000 cycles was 250 N for both groups. Group A failed mainly within the metal, and zirconia failure occurred only at a high loading force. Group B exhibited failure within the metal mostly in conjunction with adhesive failure between the zirconia and T-base. Zirconia restoration screwed directly to an MUA is a viable option, but further studies with larger sample sizes are warranted.
