RESUMEN
A novel method of chemical upcycling of used poly(ethylene terephthalate) (PET) bottles by acidolysis with succinic acid (SA) was performed under microwave irradiation. The long polyester chain of PET was efficiently fragmented into small molecules and oligomers, such as terephthalic acid and α,ω-dicarboxylic acid oligo(ethylene succinate-co-terephthalate) (OEST). Various input molar ratios of SA/PET from 1.0 to 2.5 were used, and the product mixtures were separated successfully. The recovered terephthalic acid can be reused as a basic chemical. The α,ω-dicarboxylic acid OEST was used as a curing agent for epoxy resin. The recovered SA can be reused for further PET acidolysis. Structures of OEST were identified by Fourier transform infrared (FTIR) spectroscopy, 1H NMR spectroscopy, and electrospray ionization-mass spectrometry (ESI-MS). The presence of succinic anhydride as a side product was confirmed by FTIR and ESI-MS analyses. The evaporation of SA and the formation of volatile succinic anhydride compete with the acidolysis of PET. The minimum SA/PET ratio of 1.0 was selected so that the acidolysis was effective and without the SA recovery step by MEK treatment. OEST-1.0 was used for curing diglycidyl ether of bisphenol A. The structures and thermal properties of cured adducts were confirmed by FTIR and differential scanning calorimetry (DSC). This chemical upcycling method of PET is eco-friendly without the use of a solvent and a catalyst for the reaction, and all materials were recovered and they could be reused for novel polymer preparation.
RESUMEN
Bis(2-aminoethyl)terephthalamide, an amide-containing diamine, was obtained from the aminolysis of waste poly(ethylene terephthalate) bottles. This diamine reacts with various aromatic dianhydrides to form novel polyamideimides (PAIs). The formation of amic acid or ammonium carboxylate salt intermediates depends strongly on the substituents of the dianhydrides. The electron-withdrawing substituents promote the creation of an ammonium carboxylate salt, whereas the electron donors assist with the amic acid intermediate formation. These salts and amic acids were further converted into polyimides by thermal treatment. The structures of the intermediates and PAIs were characterized by Fourier transform infrared, 1H nuclear magnetic resonance (NMR), and 13C NMR spectroscopies, and their thermal properties were determined by differential scanning calorimetry and thermogravimetry. X-ray diffraction patterns and inherent viscosity values of these PAIs were also reported. By using these chemical transformations, waste poly(ethylene terephthalate) bottles were converted into high-performance PAIs. These PAIs can be used as membrane-modifying agents for industrial separation applications.
RESUMEN
The thermal stabilities, flame retardancies, and physico-mechanical properties of rice husk-reinforced polyurethane (PU-RH) foams with and without flame retardants (FRs) were evaluated. Their flammability performances were studied by UL94, LOI, and cone calorimetry tests. The obtained results combined with FTIR, TGA, SEM, and XPS characterizations were used to evaluate the fire behaviors of the PU-RH samples. The PU-RH samples with a quite low loading (7 wt%) of aluminum diethylphosphinate (OP) and 32 wt% loading of aluminum hydroxide (ATH) had high thermal stabilities, excellent flame retardancies, UL94 V-0 ratings, and LOIs of 22%-23%. PU-RH did not pass the UL94 HB standard test and completely burned to the holder clamp with a low LOI (19%). The cone calorimetry results indicated that the fireproof characteristics of the PU foam composites were considerably improved by the addition of the FRs. The proposed flame retardancy mechanism and cone calorimetry results are consistent. The comprehensive FTIR spectroscopy, TG, SEM, and XPS analyses revealed that the addition of ATH generated white solid particles, which dispersed and covered the residue surface. The pyrolysis products of OP would self-condense or react with other volatiles generated by the decomposition of PU-RH to form stable, continuous, and thick phosphorus/aluminum-rich residual chars inhibiting the transfer of heat and oxygen. The PU-RH samples with and without the FRs exhibited the normal isothermal sorption hysteresis effect at relative humidities higher than 20%. At lower values, during the desorption, this effect was not observed, probably because of the biodegradation of organic components in the RH. The findings of this study not only contribute to the improvement in combustibility of PU-RH composites and reduce the smoke or toxic fume generation, but also solve the problem of RHs, which are abundant waste resources of agriculture materials leading to the waste disposal management problems.
RESUMEN
Rigid polyurethane foam (PUF) was successfully prepared from a novel oligo-ester-ether-diol obtained from the glycolysis of waste poly(ethylene terephthalate) (PET) bottles via reaction with diethylene glycol (DEG) in the presence of ZnSO4·7H2O. The LC-MS analysis of the oligodiol enabled us to identify 67 chemical homologous structures that were composed of zero to four terephthalate (T) ester units and two to twelve monoethylene glycol (M) ether units. The flame retardant, morphological, compression, and thermal properties of rigid PUFs with and without triphenyl phosphate (TPP) were determined. The Tg values showed that TPP played a role of not only being a flame retardant, but also a plasticizer. PUF with a rather low TPP loading had an excellent flame retardancy and high thermal stability. A loading of 10 wt % TPP not only achieved a UL-94 V-0 rating, but also obtained an LOI value of 21%. Meanwhile, the PUF without a flame retardant did not achieve a UL-94 HB rating; the sample completely burned to the holder clamp and yielded a low LOI value (17%). The fire properties measured with the cone calorimeter were also discussed, and the results further proved that the flame retardancy of the PUF with the addition of TPP was improved significantly. The polymeric material meets the demands of density and compression strength for commercial PUF, as well as the needs of environmental development. The current study may help overcome the drawback of intrinsic high flammability and enlarge the fire safety applications of materials with a high percentage of recycled PET.
