High Thermal Performance Ultraviolet (368 nm) AlGaN-Based Flip-Chip LEDs with an Optimized Structure.

In this study, we have fabricated a 368 nm LED with an epitaxial Indium Tin Oxide (ITO) contact layer. We analyze the thermal performance of the flip-chip LED with a symmetric electrode and metal reflective layer, applying ANSYS to build a coupled electro-thermal finite element model (FEM) of the temperature distribution in the multiple quantum wells (MQWs). We compare our system with the traditional Au-bump flip-chip LED and a flip-chip LED with a Distributed Bragg Reflector (DBR) layer. The simulation results have shown that the flip-chip LED with a metal reflective layer and symmetric electrode exhibits better heat dissipation performance, particularly at high input power. The influence of the insulating layer on the LED chip junction temperature is also examined. The simulation data establish an effect due to the thermal conductivity of the insulating layer in terms of heat dissipation, but this effect is negligible at an insulation layer thickness ≤1 µm.

Resolving Discrepancies between State-of-the-Art Theory and Experiment for HO2 + HO2 via Multiscale Informatics.

Recent high-level theoretical calculations predict a mild temperature dependence for HO2 + HO2 inconsistent with state-of-the-art experimental determinations that upheld the stronger temperature dependence observed in early experiments. Via MultiScale Informatics analysis of the theoretical and experimental data, we identified an alternative interpretation of the raw experimental data that uses HO2 + HO2 rate constants nearly identical to theoretical predictions─implying that the theoretical and experimental data are actually consistent, at least when considering the raw data from experimental studies. Similar analyses of typical signals from low-temperature experiments indicate that an HOOOOH intermediate─identified by recent theory but absent from earlier interpretations─yields modest effects that are smaller than, but may have contributed to, the scatter in data among different experiments. More generally, the findings demonstrate that modern chemical theories and experiments have progressed to a point where meaningful comparison requires joint consideration of their data simultaneously.

Shock tube/laser absorption measurements of the reaction rates of OH with ethylene and propene.

Reaction rates of hydroxyl (OH) radicals with ethylene (C2H4) and propene (C3H6) were studied behind reflected shock waves. OH + ethylene → products (rxn 1) rate measurements were conducted in the temperature range 973-1438 K, for pressures from 2 to 10 atm, and for initial concentrations of ethylene of 500, 751, and 1000 ppm. OH + propene → products (rxn 2) rate measurements spanned temperatures of 890-1366 K, pressures near 2.3 atm, and initial propene concentrations near 300 ppm. OH radicals were produced by shock-heating tert-butyl hydroperoxide, (CH3)3-CO-OH, and monitored by laser absorption near 306.7 nm. Rate constants for the reactions of OH with ethylene and propene were extracted by matching modeled and measured OH concentration time-histories in the reflected shock region. Current data are in excellent agreement with previous studies and extend the temperature range of OH + propene data. Transition state theory calculations using recent ab initio results give excellent agreement with our measurements and other data outside our temperature range. Fits (in units of cm³/mol/s) to the abstraction channels of OH + ethylene and OH + propene are k1 = 2.23 × 104 (T)(2.745) exp(-1115 K/T) for 600-2000 K and k2 = 1.94 × 106 (T)(2.229) exp(-540 K/T) for 700-1500 K, respectively. A rate constant determination for the reaction TBHP → products (rxn 3) was also obtained in the range 745-1014 K using OH data from behind both incident and reflected shock waves. These high-temperature measurements were fit with previous low-temperature data, and the following rate expression (0.6-2.6 atm), applicable over the temperature range 400-1050 K, was obtained: k3 (1/s) = 8.13 × 10⁻¹² (T)(7.83) exp(-14598 K/T).

A shock tube study of OH + H(2)O(2) --> H(2)O + HO(2) and H(2)O(2) + M --> 2OH + M using laser absorption of H(2)O and OH.

The rate constants of the reactions: (1) H2O2+M-->2OH+M, (2) OH+H2O2-->H2O+HO2 were measured in shock-heated H(2)O(2)/Ar mixtures using laser absorption diagnostics for H(2)O and OH. Time-histories of H(2)O were monitored using tunable diode laser absorption at 2550.96 nm, and time-histories of OH were achieved using ring dye laser absorption at 306 nm. Initial H(2)O(2) concentrations were also determined utilizing the H(2)O diagnostic. On the basis of simultaneous time-history measurements of OH and H(2)O, k(2) was found to be 4.6 x 10(13) exp(-2630 K/T) [cm(3) mol(-1) s(-1)] over the temperature range 1020-1460 K at 1.8 atm; additional measurements of k(2) near 1 atm showed no significant pressure dependence. Similarly, k(1) was found to be 9.5 x 10(15) exp(-21 250 K/T) [cm(3) mol(-1) s(-1)] over the same temperature and pressure range.

Experimental study of the rate of OH + HO2 --> H2O + O2 at high temperatures using the reverse reaction.

The rate constant of the reaction OH + HO(2) --> H(2)O + O(2) (1) can be inferred at high temperatures from measurements of the rate of its reverse reaction H(2)O + O(2) --> OH + HO(2) (-1). In this work, we used laser absorption of both H(2)O and OH to study the reverse reaction in shock-heated H(2)O/O(2)/Ar mixtures over the temperature range 1600-2200 K. Initial H(2)O concentrations were determined using tunable diode laser absorption near 2.5 microm, and OH concentration time-histories were measured using UV ring dye laser absorption near 306.7 nm. Detailed kinetic analysis of the OH time-history profiles yielded a value for the rate constant k(1) of (3.3 +/- 0.9) x 10(13) [cm(3) mol(-1) s(-1)] between 1600 and 2200 K. The results of this study agree well with those reported by Srinivasan et al. (Srinivasan, N.K.; Su, M.-C.; Sutherland, J.W.; Michael, J.V.; Ruscic, B. J. Phys. Chem. A 2006, 110, 6602-6607) in the temperature regime between 1200 and 1700 K. The combination of the two studies suggests only a weak temperature dependence of k(1) above 1200 K. Data from the current study and that of Keyser (Keyser, L.F. J. Phys. Chem. 1988, 92, 1193-1200) at lower temperatures can be described by the k(1) expression proposed by Baulch et al. (Baulch, D.L.; Cobos, C.J.; Cox, R.A.; Esser, C.; Frank, P.; Just, Th.; Kerr, J.A.; Pilling, M.J.; Troe, J.; Walker, R.W.; Warnatz, J. J. Phys. Chem. Ref. Data 1992, 21, 411), k(1) = 2.89 x 10(13) exp(252/T) [cm(3) mol(-1) s(-1)]. However, it should be noted that some previous studies suggest a k(1) minimum around 1250 K (Hippler, H.; Neunaber, H.; Troe, J. J. Chem. Phys. 1995, 103, 3510-3516) or 1000 K (Kappel, C.; Luther, K.; Troe, J. Phys. Chem. Chem. Phys. 2002, 4, 4392-4398).

Hydrogen peroxide decomposition rate: a shock tube study using tunable laser absorption of H(2)O near 2.5 microm.

The thermal decomposition of hydrogen peroxide was measured behind reflected shock waves in hydrogen peroxide/inert gas mixtures using a sensitive laser diagnostic for water vapor. In these mixtures, the formation rate of water is predominantly controlled by the decomposition rate of hydrogen peroxide. Rate determinations were made over a temperature range of 1000-1200 K and a pressure range of 0.9-3.2 atm for both argon and nitrogen carrier gases. Good detection sensitivity for water was achieved using tunable diode laser absorption of water at 2550.96 nm within its v(3) fundamental band. Hydrogen peroxide decomposition rates were found to be independent of pressure at 0.9 and 1.7 atm and showed only slight influence of pressure at 3.2 atm. The best fit of the current data to the low-pressure-limit rate for H(2)O(2) dissociation in argon bath gas is k(1,0) = 10(15.97+/-0.10) exp(-21 220 +/- 250 K/T) [cm(3) mol(-1) s(-1)] (1000-1200 K). Experiments conducted in a nitrogen bath gas show a relative collision efficiency of argon to nitrogen of 0.67.