Advancing PFAS characterization: Development and optimization of a UV-H2O2-TOP assay for improved PFCA chain length preservation and organic matter tolerance.

As per- and polyfluoroalkyl substances (PFAS) infiltrate the environment via industrial, commercial, and domestic sources, the demand for robust, cost-effective, and straightforward analytical assays intensifies to enhance PFAS characterization and quantification. To address this demand, this study introduces a novel UV-H2O2-TOP assay, identifying optimal parameters such as pH (5-9), oxidant concentration (500 mM H2O2), activation rate (63 mM H2O2 h-1), and an acceptable total organic carbon (TOC) limit (~1000 mg/L TOC) to achieve maximum PFAA precursor conversion. Additional work was performed further optimizing the UV-TOP assay, by confirming its superiority to heat activation, identifying the effectiveness of different persulfate salts, and investigating different concentrations of sodium persulfate and sodium hydroxide at a 1:2.5 ratio on PFCA yield. Our investigation concluded by applying the UV-H2O2-TOP assay, using sodium persulfate as the TOP assay oxidant, to 6:2 FTS and five different AFFF samples. High-resolution mass spectrometry and an expanded analytical suite support sample analysis, facilitating direct quantification of ultra-short chain perfluoroalkyl carboxylates (PFCAs) and common fluorotelomer compounds including 5:3/5:1:2 fluorotelomer betaine and 6:2 fluorotelomer sulfonamido betaine. Results highlight several advantages of this tandem UV-activated method, including enhanced preservation of perfluoroalkyl chains (post-oxidation of 6:2 fluorotelomer sulfonate resulted in 28 % PFHpA, 47 % PFHxA, 25 % C3-C5 PFCA), capacity to handle high TOC limits (1000 mg/L TOC), and ability to incorporate higher persulfate concentrations in a single oxidation cycle.

Biotransformation of 6:2 Fluorotelomer Thioether Amido Sulfonate in Aqueous Film-Forming Foams under Nitrate-Reducing Conditions.

Despite the prevalence of nitrate reduction in groundwater, the biotransformation of per- and polyfluoroalkyl substances (PFAS) under nitrate-reducing conditions remains mostly unknown compared with aerobic or strong reducing conditions. We constructed microcosms under nitrate-reducing conditions to simulate the biotransformation occurring at groundwater sites impacted by aqueous film-forming foams (AFFFs). We investigated the biotransformation of 6:2 fluorotelomer thioether amido sulfonate (6:2 FtTAoS), a principal PFAS constituent of several AFFF formulations using both quantitative liquid chromatography-tandem mass spectrometry (LC-MS/MS) and qualitative high-resolution mass spectrometry analyses. Our results reveal that the biotransformation rates of 6:2 FtTAoS under nitrate-reducing conditions were about 10 times slower than under aerobic conditions, but about 2.7 times faster than under sulfate-reducing conditions. Although minimal production of 6:2 fluorotelomer sulfonate and the terminal perfluoroalkyl carboxylate, perfluorohexanoate was observed, fluorotelomer thioether and sulfinyl compounds were identified in the aqueous samples. Evidence for the formation of volatile PFAS was obtained by mass balance analysis using the total oxidizable precursor assay and detection of 6:2 fluorotelomer thiol by gas chromatography-mass spectrometry. Our results underscore the complexity of PFAS biotransformation and the interactions between redox conditions and microbial biotransformation activities, contributing to the better elucidation of PFAS environmental fate and impact.

Environmental Source Tracking of Per- and Polyfluoroalkyl Substances within a Forensic Context: Current and Future Techniques.

The source tracking of per- and polyfluoroalkyl substances (PFASs) is a new and increasingly necessary subfield within environmental forensics. We define PFAS source tracking as the accurate characterization and differentiation of multiple sources contributing to PFAS contamination in the environment. PFAS source tracking should employ analytical measurements, multivariate analyses, and an understanding of PFAS fate and transport within the framework of a conceptual site model. Converging lines of evidence used to differentiate PFAS sources include: identification of PFASs strongly associated with unique sources; the ratios of PFAS homologues, classes, and isomers at a contaminated site; and a site's hydrogeochemical conditions. As the field of PFAS source tracking progresses, the development of new PFAS analytical standards and the wider availability of high-resolution mass spectral data will enhance currently available analytical capabilities. In addition, multivariate computational tools, including unsupervised (i.e., exploratory) and supervised (i.e., predictive) machine learning techniques, may lead to novel insights that define a targeted list of PFASs that will be useful for environmental PFAS source tracking. In this Perspective, we identify the current tools available and principal developments necessary to enable greater confidence in environmental source tracking to identify and apportion PFAS sources.

Identification and Fate of Aqueous Film Forming Foam Derived Per- and Polyfluoroalkyl Substances in a Wastewater Treatment Plant.

The fate of per- and polyfluoroalkyl substances (PFASs) derived from aqueous film forming foam (AFFF) was investigated within a wastewater treatment plant (WWTP) receiving large AFFF inputs from a foam refractory testing event. Targeted analysis, the Total Oxidizable Precursor Assay (TOP Assay), and nontargeted analysis with quadrupole time-of-flight (QTOF) were used to characterize the samples. Over the duration of foam testing, approximately 10.8 kg of total PFASs was measured by TOP Assay in the influent, and 6.3 kg of total PFASs was measured in the effluent; 94 g of PFOS was released in the effluent, apparently from remobilization of historical sources. 1.7% of total PFASs measured in the influent were converted to short chain perfluoroalkyl carboxylates in the effluent. Ten PFAS classes previously reported, including 6:2 fluorotelomer thioether amido sulfonate (6:2 FtTAoS), and 5 PFAS classes newly reported were identified by QTOF. The trickling filter was the only unit operation that resulted in significant gains and losses of individual PFASs, including near complete loss of 6:2 FtTAoS due to transformation. Similar reaction pathways for 6:2 FtTAoS reported in previously published soil and activated sludge microcosm experiments were observed in this WWTP, although a higher yield of perfluoroheptanoic acid was observed.

Biotransformation of AFFF Component 6:2 Fluorotelomer Thioether Amido Sulfonate Generates 6:2 Fluorotelomer Thioether Carboxylate under Sulfate-Reducing Conditions.

The fate of per and polyfluoroalkyl substances (PFASs) in aqueous filmforming foams (AFFFs) under anaerobic conditions has not been well characterized, leaving major gaps in our understanding of PFAS fate and transformation at contaminated sites. In this study, the biotransformation of 6:2 fluorotelomer thioether amido sulfonate (6:2 FtTAoS), a component of several AFFF formulations, was investigated under sulfate-reducing conditions in microcosms inoculated with either pristine or AFFF-impacted solids. To identify the transformation products, we used high-resolution mass spectrometry and employed suspect-screening and nontargeted compound identification methods. These analyses demonstrated that 6:2 FtTAoS was transformed primarily to a stable polyfluoroalkyl compound, 6:2 fluorotelomer thioether propionate (6:2 FtTP). It did not undergo further reactions to produce the perfluoroalkyl carboxylates and fluorotelomer sulfonates and carboxylates that were observed during aerobic transformations. Here, the 6:2 FtTP was recalcitrant to biotransformation, indicating the stability of the thioether group under sulfate reducing conditions. The total oxidizable precursor (TOP) assay was used to assess the presence of other PFASs. Although nearly all of the PFAS mass initially present was recovered from the pristine microcosms, only 67% of the initial PFAS mass was recovered from the contaminated microcosms, suggesting the formation of volatile biotransformation products or those that could not be detected by the TOP assay.

Poly- and perfluoroalkyl substances in wastewater: Significance of unknown precursors, manufacturing shifts, and likely AFFF impacts.

In late 2014, wastewater effluent samples were collected from eight treatment plants that discharge to San Francisco (SF) Bay in order to assess poly- and perfluoroalkyl substances (PFASs) currently released from municipal and industrial sources. In addition to direct measurement of twenty specific PFAS analytes, the total concentration of perfluoroalkyl acid (PFAA) precursors was also indirectly measured by adapting a previously developed oxidation assay. Effluent from six municipal treatment plants contained similar amounts of total PFASs, with highest median concentrations of PFHxA (24 ng/L), followed by PFOA (23 ng/L), PFBA (19 ng/L), and PFOS (15 ng/L). Compared to SF Bay municipal wastewater samples collected in 2009, the short chain perfluorinated carboxylates PFBA and PFHxA rose significantly in concentration. Effluent samples from two treatment plants contained much higher levels of PFASs: over two samplings, wastewater from one municipal plant contained an average of 420 ng/L PFOS and wastewater from an airport industrial treatment plant contained 560 ng/L PFOS, 390 ng/L 6:2 FtS, 570 ng/L PFPeA, and 500 ng/L PFHxA. The elevated levels observed in effluent samples from these two plants are likely related to aqueous film forming foam (AFFF) sources impacting their influent; PFASs attributable to both current use and discontinued AFFF formulations were observed. Indirectly measured PFAA precursor compounds accounted for 33%-63% of the total molar concentration of PFASs across all effluent samples and the PFAA precursors indicated by the oxidation assay were predominately short-chained. PFAS levels in SF Bay effluent samples reflect the manufacturing shifts towards shorter chained PFASs while also demonstrating significant impacts from localized usage of AFFF.

Aerobic Biotransformation of Fluorotelomer Thioether Amido Sulfonate (Lodyne) in AFFF-Amended Microcosms.

The aerobic biotransformation pathways of 4:2, 6:2, and 8:2 fluorotelomer thioether amido sulfonate (FtTAoS) were characterized by determining the fate of the compounds in soil and medium microcosms amended with an aqueous film-forming foam (AFFF) solution. The biotransformation of FtTAoS occurred in live microcosms over approximately 40 days and produced 4:2, 6:2, and 8:2 fluorotelomer sulfonate (FtS), 6:2 fluorotelomer unsaturated carboxylic acid (FtUCA), 5:3 fluorotelomer carboxylic acid (FtCA), and C4 to C8 perfluorinated carboxylic acids (PFCAs). Two biotransformation products corresponding to singly and doubly oxygenated forms of 6:2 FtTAoS were also identified through high resolution mass spectrometry (MS) analysis and liquid chromatography tandem-MS. An oxidative assay was used to indirectly quantify the total concentration of polyfluorinated compounds and check the mass balance. The assay produced near complete mass recovery of FtTAoS after biotransformation, with 10% (mol/mol) of the amended FtTAoS accounted for in FtS, FtCA, and PFCA products. The transformation rates of identified products appear to be slow relative to FtTAoS, indicating that some intermediates may persist in the environment. This study confirms some of the sources of FtS and PFCAs in groundwater and soil at AFFF-impacted sites and suggests that fluorinated intermediates that are not routinely measured during the biotransformation of PFASs may accumulate.

Evidence of remediation-induced alteration of subsurface poly- and perfluoroalkyl substance distribution at a former firefighter training area.

Poly- and perfluoroalkyl substances (PFASs) are a class of fluorinated chemicals that are utilized in firefighting and have been reported in groundwater and soil at several firefighter training areas. In this study, soil and groundwater samples were collected from across a former firefighter training area to examine the extent to which remedial activities have altered the composition and spatial distribution of PFASs in the subsurface. Log Koc values for perfluoroalkyl acids (PFAAs), estimated from analysis of paired samples of groundwater and aquifer solids, indicated that solid/water partitioning was not entirely consistent with predictions based on laboratory studies. Differential PFAA transport was not strongly evident in the subsurface, likely due to remediation-induced conditions. When compared to the surface soil spatial distributions, the relative concentrations of perfluorooctanesulfonate (PFOS) and PFAA precursors in groundwater strongly suggest that remedial activities altered the subsurface PFAS distribution, presumably through significant pumping of groundwater and transformation of precursors to PFAAs. Additional evidence for transformation of PFAA precursors during remediation included elevated ratios of perfluorohexanesulfonate (PFHxS) to PFOS in groundwater near oxygen sparging wells.

Persistence of perfluoroalkyl acid precursors in AFFF-impacted groundwater and soil.

Several classes of polyfluorinated chemicals that are potential precursors to the perfluorinated carboxylates and sulfonates are present in aqueous film-forming foams (AFFF). To assess the persistence of these AFFF-derived precursors, groundwater, soil, and aquifer solids were obtained in 2011 from an unlined firefighter training area at a U.S. Air Force Base where AFFF was regularly used between 1970 and 1990. To measure the total concentration of perfluorinated carboxylate and sulfonate precursors in archived AFFF formulations and AFFF-impacted environmental samples, a previously developed assay that uses hydroxyl radical to oxidize precursors to perfluorinated carboxylates was adapted for these media. This assay was employed along with direct measurement of 22 precursors found in AFFF and a suite of other poly- and perfluoroalkyl substances (PFASs). On a molar basis, precursors accounted for 41-100% of the total concentration of PFASs in archived AFFF formulations. In the training area, precursors measured by the oxidation assay accounted for an average of 23% and 28% of total PFASs (i.e., precursors and perfluorinated carboxylates and sulfonates) in groundwater and solids samples, respectively. One precursor in AFFF, perfluorohexane sulfonamide amine, was observed on several highly contaminated soil and aquifer solids samples, but no other precursors present in AFFF formulations were detected in any samples at this field site. Suspected intermediate transformation products of precursors in AFFF that were directly measured accounted for approximately half of the total precursor concentration in samples from the training site. The fraction of PFASs consisting of perfluorinated carboxylates and sulfonates was greater in groundwater and solid samples than in any archived AFFF formulations, suggesting that much of the mass of precursors released at the site was converted to perfluorinated carboxylates and sulfonates. The precursors that have persisted at this site may generate significant amounts of additional perfluorinated carboxylates and sulfonates upon remediation of contaminated groundwater or aquifer solids.

Oxidative conversion as a means of detecting precursors to perfluoroalkyl acids in urban runoff.

A new method was developed to quantify concentrations of difficult-to-measure and unidentified precursors of perfluoroalkyl carboxylic (PFCA) and sulfonic (PFSA) acids in urban runoff. Samples were exposed to hydroxyl radicals generated by thermolysis of persulfate under basic pH conditions and perfluoroalkyl acid (PFAA) precursors were transformed to PFCAs of related perfluorinated chain length. By comparing PFCA concentrations before and after oxidation, the concentrations of total PFAA precursors were inferred. Analysis of 33 urban runoff samples collected from locations around the San Francisco Bay, CA indicated that PFOS (2.6-26 ng/L), PFOA (2.1-16 ng/L), and PFHxA (0.9-9.7 ng/L) were the predominant perfluorinated compounds detected prior to sample treatment. Following oxidative treatment, the total concentrations of PFCAs with 5-12 membered perfluoroalkyl chains increased by a median of 69%, or between 2.8 and 56 ng/L. Precursors that produced PFHxA and PFPeA upon oxidation were more prevalent in runoff samples than those that produced PFOA, despite lower concentrations of their corresponding perfluorinated acids prior to oxidation. Direct measurements of several common precursors to PFOS and PFOA (e.g., perfluorooctanesulfonamide and 8:2 fluorotelomer sulfonate) accounted for less than 25% of the observed increase in PFOA, which increased by a median value of 37%. Exposure of urban runoff to sunlight, advanced oxidation processes, or microbes could result in modest, but measurable, increases in concentrations of PFCAs and PFSAs.

Photosensitized degradation of caffeine: role of fulvic acids and nitrate.

The photolysis of caffeine was studied in solutions of fulvic acid isolated from Suwannee River, GA (SRFA) and Old Woman Creek Natural Estuarine Research Reserve, OH (OWCFA) with different chemical amendments (nitrate and iron). Caffeine degrades slowly by direct photolysis (>170 h in artificial sunlight), but we observed enhanced photodegradation in waters containing the fulvic acids. At higher initial concentrations (10 µM) the indirect photolysis of caffeine occurs predominantly through reaction with the hydroxyl radical (OHⁱ) generated by irradiated fulvic acids. Both rate constant estimates based upon measured OHⁱ steady-state concentrations and quenching studies using isopropanol corroborate the importance of this pathway. Further, OHⁱ generated by irradiated nitrate at concentrations present in wastewater effluent plays an important role as a photosensitizer even in the presence of fulvic acids, while the photo-Fenton pathway does not at neutral or higher pH. At lower initial concentrations (0.1 µM) caffeine photolysis reactions proceed even more quickly in fulvic acid solutions and are influenced by both short- and long-lived reactive species. Studies conducted under suboxic conditions suggest that an oxygen dependent long-lived radical e.g., peroxyl radicals plays an important role in the degradation of caffeine at lower initial concentration.