Comparative investigation of known and unknown disinfection by-product precursor removal and microbial community from biological biochar and activated carbon filters.

Biological activated carbon filter (BAC) is one of the most effective technologies for removing disinfection by-product (DBP) precursors from water. Biochar is a lower-cost medium that has the potential to replace granular activated carbon in BAC applications, thus leading to the development of biological biochar filter (BCF). This study compared BCF with BAC for the removal of DBP precursors using column experiments. Both BCF and BAC achieved the removal of DBP precursors, resulting in concentrations of all DBP formation potential below the World Health Organization guideline values for drinking water. Bromodichloromethane and unknown DBP precursor removal by BCF was comparable to that by BAC. However, BAC removed more chloroform and dichloroacetontrile precursors than BCF. For microbial community analysis, cell numbers in a bottom layer (inlet) of BCF and BAC columns were higher than those in the top layer. The abundances of Nordella and a microbial genus from Burkholderiaceae at the bottom layer showed a strong correlation to the number of DBP precursors removed and were comparable in BCF and BAC. This finding likely contributes to the similarities between DBPs species removed and the removal performances of some known and unknown DBP precursors by BCF and BAC. Overall results from this study revealed that biochar can be served as a low-cost and sustainable replacement of activated carbon in water filter for DBP precursor removal.

Integrated remediation and detoxification of triclocarban-contaminated water using waste-derived biochar-immobilized cells by long-term column experiments.

Triclocarban (TCC), an antibacterial agent commonly used in personal care products, is one of the top ten contaminants of emerging concern in various environmental media, including soil and contaminated water in vadose zone. This study aimed to investigate TCC-contaminated water remediation using biochar-immobilized bacterial cells. Pseudomonas fluorescens strain MC46 (MC46), an efficient TCC-degrading isolate, was chosen, whereas agro-industrial carbonized waste as biochar was directly used as a sustainable cell immobilization carrier. According to the long-term TCC removal performance results (160 d), the biochar-immobilized cells consistently exhibited high TCC removal efficiencies (84-97%), whereas the free MC46 removed TCC for 76-94%. At 100 days, the detachment of the MC46 cells from the immobilized cell column was observed. The micro-Fourier-transform infrared spectroscopy results indicated that extracellular polymeric substance (EPS) was produced, but polysaccharide and protein fractions were washed out of the column. The lipid fraction of EPS adhered to the biochar, promoting TCC sorption for long-term treatment. The shortening of MC46 cells improved the tolerance of TCC toxicity. The TCC-contaminated water was successfully detoxified by the biochar-immobilized MC46 cells. Overall, the waste-derived biochar-immobilized cell system proposed in this study for the removal of emerging contaminants, including TCC, is efficient, economical, and aligned with the sustainable development concept of value-added utilization of waste.

Controlling In Planta Gold Nanoparticle Synthesis and Size for Catalysis.

Gold nanoparticles (Au-NPs) are used as catalysts for a diverse range of industrial applications. Currently, Au-NPs are synthesized chemically, but studies have shown that plants fed Au deposit, this element naturally as NPs within their tissues. The resulting plant material can be used to make biomass-derived catalysts. In vitro studies have shown that the addition of specific, short (∼10 amino acid) peptide/s to solutions can be used to control the NP size and shape, factors that can be used to optimize catalysts for different processes. Introducing these peptides into the model plant species, Arabidopsis thaliana (Arabidopsis), allows us to regulate the diameter of nanoparticles within the plant itself, consequently influencing the catalytic performance in the resulting pyrolyzed biomass. Furthermore, we show that overexpressing the copper and gold COPPER TRANSPORTER 2 (COPT2) in Arabidopsis increases the uptake of these metals. Adding value to the Au-rich biomass offers the potential to make plant-based remediation and stabilization of mine wastes financially feasible. Thus, this study represents a significant step toward engineering plants for the sustainable recovery of finite and valuable elements from our environment.

The dominance and growth of shallow groundwater resources in continuous permafrost environments.

Water is a limited resource in Arctic watersheds with continuous permafrost because freezing conditions in winter and the impermeability of permafrost limit storage and connectivity between surface water and deep groundwater. However, groundwater can still be an important source of surface water in such settings, feeding springs and large aufeis fields that are abundant in cold regions and generating runoff when precipitation is rare. Whether groundwater is sourced from suprapermafrost taliks or deeper regional aquifers will impact water availability as the Arctic continues to warm and thaw. Previous research is ambiguous about the role of deep groundwater, leading to uncertainty regarding Arctic water availability and changing water resources. We analyzed chemistry and residence times of spring, stream, and river waters in the continuous permafrost zone of Alaska, spanning the mountains to the coastal plain. Water chemistry and age tracers show that surface waters are predominately sourced from recent precipitation and have short (<50 y) subsurface residence times. Remote sensing indicates trends in the areal extent of aufeis over the last 37 y, and correlations between aufeis extent and previous year summer temperature. Together, these data indicate that surface waters in continuous permafrost regions may be impacted by short flow paths and shallow suprapermafrost aquifers that are highly sensitive to climatic and hydrologic change over annual timescales. Despite the lack of connection to regional aquifers, continued warming and permafrost thaw may promote deepening of the shallow subsurface aquifers and creation of shallow taliks, providing some resilience to Arctic freshwater ecosystems.

Sustainable methods for the carboxymethylation and methylation of ursolic acid with dimethyl carbonate under mild and acidic conditions.

Ursolic acid is a triterpene plant extract that exhibits significant potential as an anti-cancer, anti-tumour, and anti-inflammatory agent. Its direct use in the pharmaceutical industry is hampered by poor uptake of ursolic acid in the human body coupled with rapid metabolism causing a decrease in bioactivity. Modification of ursolic acid can overcome such issues, however, use of toxic reagents, unsustainable synthetic routes and poor reaction metrics have limited its potential. Herein, we demonstrate the first reported carboxymethylation and/or methylation of ursolic acid with dimethyl carbonate (DMC) as a green solvent and sustainable reagent under acidic conditions. The reaction of DMC with ursolic acid, in the presence of PTSA, ZnCl2, or H2SO4-SiO2 yielded the carboxymethylation product 3ß-[[methoxy]carbonyl]oxyurs-12-en-28-oic acid, the methylation product 3ß-methoxyurs-12-en-28-oic acid and the dehydration product urs-2,12-dien-28-oic acid. PTSA demonstrated high conversion and selectivity towards the previously unreported carboxymethylation of ursolic acid, while the application of formic acid in the system led to formylation of ursolic acid (3ß-formylurs-12-en-28-oic acid) in quantitative yields via esterification, with DMC acting solely as a solvent. Meanwhile, the methylation product of ursolic acid, 3ß-methoxyurs-12-en-28-oic acid, was successfully synthesised with FeCl3, demonstrating exceptional conversion and selectivity, >99% and 99%, respectively. Confirmed with the use of qualitative and quantitative green metrics, this result represents a significant improvement in conversion, selectivity, safety, and sustainability over previously reported methods of ursolic acid modification. It was demonstrated that these methods could be applied to other triterpenoids, including corosolic acid. The study also explored the potential pharmaceutical applications of ursolic acid, corosolic acid, and their derivatives, particularly in anti-inflammatory, anti-cancer, and anti-tumour treatments, using molecular ADMET and docking methods. The methods developed in this work have led to the synthesis of novel molecules, thus creating opportunities for the future investigation of biological activity and the modification of a wide range of triterpenoids applying acidic DMC systems to deliver novel active pharmaceutical intermediates.

Evidence of heat sensitivity in people with Parkinson's disease.

Examining how heat affects people with Parkinson's disease is essential for informing clinical decision-making, safety, well-being, and healthcare planning. While there is evidence that the neuropathology associated with Parkinson's disease affects thermoregulatory mechanisms, little attention has been given to the association of heat sensitivity to worsening symptoms and restricted daily activities in people with this progressive disease. Using a cross-sectional study design, we examined the experiences of people diagnosed with Parkinson's disease in the heat. Two-hundred and forty-seven people completed an online survey (age: 66.0 ± 9.2 years; sex: male = 102 (41.3%), female = 145 (58.7%)), of which 195 (78.9%) reported becoming more sensitive to heat with Parkinson's disease. Motor and nonmotor symptoms worsened with heat in 182 (73.7%) and 203 (82.2%) respondents, respectively. The most commonly reported symptoms to worsen included walking difficulties, balance impairment, stiffness, tremor, fatigue, sleep disturbances, excess sweating, difficulty concentrating, and light-headedness when standing. Concerningly, over half indicated an inability to work effectively in the heat, and nearly half reported that heat impacted their ability to perform household tasks and social activities. Overall, heat sensitivity was common in people with Parkinson's disease and had a significant impact on symptomology, day-to-day activities and quality of life.

Enhanced microwave assisted pyrolysis of waste rice straw through lipid extraction with supercritical carbon dioxide.

A combination of supercritical carbon dioxide (scCO2) extraction and microwave-assisted pyrolysis (MAP) have been investigated for the valorisation of waste rice straw. ScCO2 extraction of rice straw led to a 0.7% dry weight yield of lipophilic molecules, at elevated temperatures of 65 °C and pressures of 400 bar. Lipid compositions (fatty acids, fatty alcohol, fatty aldehydes, steroid ketones, phytosterols, n-alkanes and wax esters) of the waxes obtained by scCO2 were comparable to those obtained Soxhlet extraction using the potentially toxic solvent n-hexane. ScCO2 extraction positively influenced the pyrolysis heating rate, with a rate of 420 K min-1 for particles of 500-2000 µm, compared to 240 K min-1 for the same particle size of untreated straw. Particle size significantly affected cellulose decomposition and the distribution of pyrolysis products (gaseous, liquid and char), highlighting the importance of selecting an adequate physical pre-treatment. TG and DTG of the original rice straw and resulting biochar produced indicated that cellulose was completely decomposed during the MAP. While a rapid pressure change occurred at ∼120 °C (size > 2000 µm) and ∼130 °C (size 500-2000 µm) during MAP and was associated with the production of incondensable gas during cellulose decomposition, this takes place at significantly lower temperatures than those observed with conventional pyrolysis, 320 °C. Wax removal by scCO2 influences the dielectric properties of the straw, enhancing microwave absorption with rapid heating rates and elevated final pyrolysis temperatures, illustrating the benefits of combining these sustainable technologies within a holistic rice straw biorefinery.

Hot water immersion acutely reduces peripheral glucose uptake in young healthy males: An exploratory crossover randomized controlled trial.

Whether glucose concentration increases during heat exposure because of reduced peripheral tissue uptake or enhanced appearance is currently unknown. This study aimed to report glucose concentrations in both capillary and venous blood in response to a glucose challenge during passive heating (PH) to assess whether heat exposure affects glucose uptake in healthy males. Twelve healthy male participants completed two experimental sessions, where they were asked to undertake an oral glucose tolerance test (OGTT) whilst immersed in thermoneutral (CON, 35.9 (0.6) °C) and hot water (HWI, 40.3 (0.5) °C) for 120 min. Venous and capillary blood [glucose], rectal temperature, and heart rate were recorded. [Glucose] area under the curve for HWI venous (907 (104) AU) differed from CON venous (719 (88) AU, all P < 0.001). No other differences were noted (P > 0.05). Compared with CON, HWI resulted in greater rectal temperature (37.1 (0.3) °C versus 38.6 (0.4) °C, respectively) and heart rate (69 (12) bpm versus 108 (11) bpm, respectively) on cessation (P < 0.001). An OGTT results in similar capillary [glucose] during hot and thermoneutral water immersion, whereas venous [glucose] was greater during HWI when compared with CON. This indicates that peripheral tissue glucose uptake is acutely reduced in response to HWI. Abbreviations: AUC: Area under the curve; CON: Thermoneutral immersion trial; HWI: Hot water immersion trial; OGTT: Oral glucose tolerance test; PH: Passive heating; T-msk: Mean skin temperature; Trec: Rectal temperature.

Impact of Posterior Left Atrial Voltage on Ablation Outcomes in Persistent Atrial Fibrillation: CAPLA Substudy.

BACKGROUND: Pulmonary vein isolation (PVI) is less effective in patients with persistent atrial fibrillation (PsAF). Adjunctive ablation targeting low voltage areas (LVAs) may improve arrhythmia outcomes. OBJECTIVES: This study aims to compare the outcomes of adding posterior wall isolation (PWI) to PVI, vs PVI alone in PsAF patients with posterior wall LVAs. METHODS: The CAPLA (Effect of Catheter Ablation Using Pulmonary Vein Isolation With vs Without Posterior Left Atrial Wall Isolation on Atrial Arrhythmia Recurrence in Patients With Persistent Atrial Fibrillation) study was a multicenter, randomized trial involving PsAF patients randomized 1:1 to either PVI alone or PVI with PWI. Voltage mapping performed during pacing pre-ablation was reviewed offline, with LVA defined as bipolar voltage of <0.5 mV. The primary endpoint was freedom from any documented atrial arrhythmia of >30 seconds off antiarrhythmic medication at 12 months after a single ablation procedure in patients with posterior LVA. RESULTS: A total of 210 patients (average 64.6 ± 9.2 years,73.3% males, median atrial fibrillation duration 4.5 months [IQR: 2 to 8 months]) underwent multipolar left atrial mapping during coronary sinus pacing with posterior LVA present in 69 (32.9%). Patients with posterior LVA were more likely to have LVA in other atrial regions (91.7% vs 57.1%; P < 0.01), larger left atrial diameter (4.8 cm vs 4.4 cm; P < 0.01), and significantly increased risk of atrial arrhythmia recurrence at 12 months (LVA: 56.5% vs no LVA: 41.4%; HR: 1.51; 95% CI: 1.01-2.27; P = 0.04) compared to no posterior LVA. However, the addition of PWI to PVI did not significantly improve freedom from atrial arrhythmia recurrence over PVI alone (PVI with PWI: 44.8% vs PVI: 41.9%; HR: 0.95; 95% CI: 0.51-1.79; P = 0.95). CONCLUSIONS: In patients with PsAF undergoing catheter ablation, posterior LVA was associated with a significant increase in atrial arrhythmia recurrence. However, the addition of PWI in those with posterior LVA did not reduce atrial arrhythmia recurrence over PVI alone.

Posterior Wall Isolation Improves Outcomes for Persistent AF With Rapid Posterior Wall Activity: CAPLA Substudy.

BACKGROUND: Pulmonary vein isolation (PVI) is less effective in persistent atrial fibrillation (PerAF) than in paroxysmal atrial fibrillation (AF). However, the CAPLA (Effect of Catheter Ablation Using Pulmonary Vein Isolation With vs Without Posterior Left Atrial Wall Isolation on Atrial Arrhythmia Recurrence in Patients With Persistent Atrial Fibrillation: The CAPLA randomized clinical trial) of PVI vs posterior wall isolation (PWI) did not support empiric PWI in PerAF. We examined pulmonary vein (PV) and posterior wall (PW) electrical characteristics to determine if select patients may benefit from additional PWI. OBJECTIVES: This study sought to determine the impact of PV and PW electrical characteristics on AF ablation outcomes in the CAPLA randomized study. METHODS: Participants in spontaneous AF at the time of ablation were included from the CAPLA study. The mean, shortest, and longest PV, PW, and left atrial (LA) appendage cycle length measurements were annotated preablation using a multipolar catheter for 100 consecutive cycles. Next, cardioversion was performed with a high-density LA voltage map completed. Cox proportional hazards regression was utilized to determine clinical and electroanatomic predictors of AF recurrence overall and according to ablation strategy. Follow-up included twice daily single-lead electrocardiograms or continuous monitoring for 12 months. RESULTS: A total of 151 patients (27% female, age 65 ± 9 years, 18% long-standing PerAF, LA volume index 52 ± 16 mL/m2, median AF duration 5 months [IQR: 2-10 months]) were in AF on the day of procedure and were randomized to PVI alone (50%) or PVI+PWI (50%) according to the CAPLA randomized clinical trial protocol. Baseline clinical, echocardiographic, and electroanatomic parameters were comparable between groups (all P > 0.05) including PV and PW characteristics. After 12 months, freedom from AF off antiarrhythmic drug therapy was 51.7% in PVI and 49.7% in PVI+PWI (log-rank P = 0.564). Rapid PW activity was defined as less than the median of the shortest PW cycle length (140 ms) and rapid PV activity was defined as less than the median of the shortest PV cycle length (126 ms). In those with rapid PW activity, the addition of PWI was associated with greater arrhythmia-free survival (56.4%) vs PVI alone (38.6%) (HR: 0.78; 95% CI: 0.67-0.94; log-rank P = 0.030). Moreover, in those undergoing PVI only, the risk of AF recurrence was higher in those with rapid PW activity (55.3% vs 46.5% in slower PW activity; HR: 1.50, 95%CI 1.11-2.26; log-rank P = 0.036). Rapid PV activity and PV cycle length (individual PVs or average of all 4 PVs) were not associated with outcome (all P > 0.05) regardless of ablation strategy. There was no correlation between PW cycle length and posterior low voltage (r = -0.06, P = 0.496). The addition of PWI did not improve arrhythmia-free survival in subgroups with LA enlargement (LA volume index >34 mL/m2) (HR: 0.69; 95% CI: 0.39-1.25; P = 0.301), posterior low-voltage zone (HR: 1.06; 95% CI: 0.68-1.66; P = 0.807), or long-standing PerAF (HR: 1.10; 95% CI: 0.71-1.72; P = 0.669). CONCLUSIONS: Rapid PW activity is associated with an increased risk of AF recurrence post-catheter ablation. The addition of PWI in this subgroup was associated with a significant improvement in freedom from AF compared with PVI alone. The presence of rapid PW activity may identify patients with PerAF likely to benefit from PWI.

Radiation Pneumonitis, Really? A Case of Pulmonary Toxicity from CDK4/6 Inhibitor.

BACKGROUND/AIM: Radiation pneumonitis is a known complication of radiotherapy. It is also a rare complication of CDK4/6 inhibitors, and it can be difficult to differentiate the two. This is a report of a case of pulmonary toxicity from a CDK4/6 inhibitor, which was initially ascribed to radiation pneumonitis. CASE REPORT: A 77-year-old female was diagnosed with pneumonitis after receiving radiation to the thoracic spine. She had also been treated with abemaciclib. Upon review, the patient's lung mean dose was 11.54 Gy with a V20 of 17.02%, and the area of pneumonitis was largely outside of the treatment field. Abemaciclib was ceased. The patient was started on supportive oxygen as well as steroids. She no longer required oxygen and she was discharged from the hospital. Radiation pneumonitis is largely correlated with the volume of lung radiated and dose of radiation to the lung. CDK4/6 inhibitor pulmonary toxicity, while rare, is possible and will likely become more frequent with increasing use of these agents. CONCLUSION: Patients receiving CDK4/6 inhibitors are at an increased risk for pneumonitis. It can be confused with radiation pneumonitis and must be included in the differential diagnosis.

A rapid cell-free expression and screening platform for antibody discovery.

Antibody discovery is bottlenecked by the individual expression and evaluation of antigen-specific hits. Here, we address this bottleneck by developing a workflow combining cell-free DNA template generation, cell-free protein synthesis, and binding measurements of antibody fragments in a process that takes hours rather than weeks. We apply this workflow to evaluate 135 previously published antibodies targeting the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), including all 8 antibodies previously granted emergency use authorization for coronavirus disease 2019 (COVID-19), and demonstrate identification of the most potent antibodies. We also evaluate 119 anti-SARS-CoV-2 antibodies from a mouse immunized with the SARS-CoV-2 spike protein and identify neutralizing antibody candidates, including the antibody SC2-3, which binds the SARS-CoV-2 spike protein of all tested variants of concern. We expect that our cell-free workflow will accelerate the discovery and characterization of antibodies for future pandemics and for research, diagnostic, and therapeutic applications more broadly.

Computational approaches for drug repurposing in oncology: untapped opportunity for high value innovation.

Historically, the effort by academia and industry to develop new chemical entities into lifesaving drugs has limited success in meeting the demands of today's healthcare. Repurposing drugs that are originally approved by the United States Food and Drug Administration or by regulatory authorities around the globe is an attractive strategy to rapidly develop much-needed therapeutics for oncologic indications that extend from treating cancer to managing treatment-related complications. This review discusses computational approaches to harness existing drugs for new therapeutic use in oncology.

A Systematic Review of Post-Work Core Temperature Cooling Rates Conferred by Passive Rest.

Physical work increases energy expenditure, requiring a considerable elevation of metabolic rate, which causes body heat production that can cause heat stress, heat strain, and hyperthermia in the absence of adequate cooling. Given that passive rest is often used for cooling, a systematic search of literature databases was conducted to identify studies that reported post-work core temperature cooling rates conferred by passive rest, across a range of environmental conditions. Data regarding cooling rates and environmental conditions were extracted, and the validity of key measures was assessed for each study. Forty-four eligible studies were included, providing 50 datasets. Eight datasets indicated a stable or rising core temperature in participants (range 0.000 to +0.028 °C min-1), and forty-two datasets reported reducing core temperature (-0.002 to -0.070 °C min-1) during passive rest, across a range of Wet-Bulb Globe Temperatures (WBGT). For 13 datasets where occupational or similarly insulative clothing was worn, passive rest resulted in a mean core temperature decrease of -0.004 °C min-1 (-0.032 to +0.013 °C min-1). These findings indicate passive rest does not reverse the elevated core temperatures of heat-exposed workers in a timely manner. Climate projections of higher WBGT are anticipated to further marginalise the passive rest cooling rates of heat-exposed workers, particularly when undertaken in occupational attire.

Adsorption of the non-steroidal anti-inflammatory drug (ibuprofen) onto biochar and magnetic biochar prepared from chrysanthemum waste of the beverage industry.

Biochar and magnetic biochar prepared from chrysanthemum waste of the beverage industry are effective adsorbents for the removal of the non-steroidal anti-inflammatory drug, ibuprofen (IBP), from aqueous systems. The development of magnetic biochar using iron chloride, overcame poor separation characteristics from the liquid phase of the powdered biochar after adsorption. Characterisation of biochars was achieved through Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), N2 adsorption/desorption porosimetry, scanning electron microscopy (SEM), electron dispersive X-ray analysis (EDX), X-ray photoelectron spectroscopy (XPS), vibrating sample magnetometer (VSM), moisture and ash content, bulk density, pH and zero-point charge (pHpzc). The specific surface area of non-magnetic and magnetic biochars was 220 and 194 m2 g-1, respectively. Adsorption of ibuprofen was optimised with respect to contact time (5-180 min), solution pH (2-12) and initial drug concentration (5-100 mg L-1), with equilibrium being reached in 1 hour, and the maximum ibuprofen removal occurred at pH 2 and 4 for biochar and magnetic biochars, respectively. Investigation of the adsorption kinetics was achieved through application of the pseudo-first order, pseudo-second order, Elovich and intra-particle diffusion models. Adsorption equilibrium was evaluated using Langmuir, Freundlich and Langmuir-Freundlich isotherm models. The adsorption kinetics and isotherms for both biochars are well described by pseudo-second order kinetic and Langmuir-Freundlich isotherm models, respectively, with the maximum adsorption capacity of biochar and magnetic biochar being 167 and 140 mg g-1, respectively. Chrysanthemum derived non-magnetic and magnetic biochars exhibited significant potential as sustainable adsorbents toward the removal of emerging pharmaceutical pollutants such as ibuprofen from aqueous solution.

Climate Change Effects on the Predicted Heat Strain and Labour Capacity of Outdoor Workers in Australia.

Global heating is subjecting more of the planet to longer periods of higher heat stress categories commonly employed to determine safe work durations. This study compared predicted worker heat strain and labour capacity for a recent normal climate (1986-2005) and under commonly applied climate scenarios for the 2041-2080 period for selected Australian locations. Recently published heat indices for northern (Darwin, Townsville, and Tom Price) and south-eastern coastal and inland Australia locations (Griffith, Port Macquarie, and Clare) under four projected climate scenarios, comprising two representative concentration pathways (RCPs), RCP4.5 and RCP8.5, and two time periods, 2041-2060 and 2061-2080, were used. Safe work durations, before the threshold for core temperature (38.0 °C) or sweat loss (5% body mass) are attained, were then estimated for each scenario using the predicted heat strain model (ISO7933). The modelled time to threshold core temperature varied with location, climate scenario, and metabolic rate. Relative to the baseline (1986-2005), safe work durations (labour capacity) were reduced by >50% in Port Macquarie and Griffith and by 20-50% in northern Australia. Reaching the sweat loss limit restricted safe work durations in Clare and Griffith. Projected future climatic conditions will adversely impact the predicted heat strain and labour capacity of outdoor workers in Australia. Risk management strategies must adapt to warming conditions to protect outdoor workers from the deleterious effects of heat.

Lower Extremity Inverse Kinematics Results Differ Between Inertial Measurement Unit- and Marker-Derived Gait Data.

In-lab, marker-based gait analyses may not represent real-world gait. Real-world gait analyses may be feasible using inertial measurement units (IMUs) in combination with open-source data processing pipelines (OpenSense). Before using OpenSense to study real-world gait, we must determine whether these methods estimate joint kinematics similarly to traditional marker-based motion capture (MoCap) and differentiate groups with clinically different gait mechanics. Healthy young and older adults and older adults with knee osteoarthritis completed this study. We captured MoCap and IMU data during overground walking at 2 speeds. MoCap and IMU kinematics were computed with OpenSim workflows. We tested whether sagittal kinematics differed between MoCap and IMU, whether tools detected between-group differences similarly, and whether kinematics differed between tools by speed. MoCap showed more anterior pelvic tilt (0%-100% stride) and joint flexion than IMU (hip: 0%-38% and 61%-100% stride; knee: 0%-38%, 58%-89%, and 95%-99% stride; and ankle: 6%-99% stride). There were no significant tool-by-group interactions. We found significant tool-by-speed interactions for all angles. While MoCap- and IMU-derived kinematics differed, the lack of tool-by-group interactions suggests consistent tracking across clinical cohorts. Results of the current study suggest that IMU-derived kinematics with OpenSense may enable reliable evaluation of gait in real-world settings.

Application of hindered ether solvents for palladium catalyzed Suzuki-Miyaura, Sonogashira and cascade Sonogashira cross-coupling reactions.

Cross-coupling and cascade reactions typically rely on unsustainable and toxic volatile organic solvents. 2,2,5,5-Tetramethyloxolane (TMO) and 2,5-diethyl-2,5-dimethyloxolane (DEDMO) are both inherently non-peroxide forming ethers, and have been used in this work as effective, more sustainable, and potentially bio-based alternative solvents for Suzuki-Miyaura and Sonogashira reactions. Suzuki-Miyaura reactions demonstrated good yields for a range of substrates, 71-89% in TMO and 63-92% in DEDMO. In addition, a Sonogashira reaction exhibited the excellent yields of 85-99% performed in TMO, which was significantly higher than traditional volatile organic solvents, THF or toluene, and higher than those reported for another non-peroxide forming ether, namely eucalyptol. Cascade Sonogashira reactions utilizing a simple annulation methodology were particularly effective in TMO. Furthermore, a green metric assessment confirmed that the methodology employing TMO was more sustainable and greener than the traditional solvents THF and toluene, thereby demonstrating the promise of TMO as an alternative solvent for Pd-catalyzed cross-coupling reactions.

Sustainable solvents for ß-diketone extraction from wheat straw wax and their molecular self-assembly into nano-structured tubules for hydrophobic coatings.

Nonpolar, nonperoxide forming, sustainable and potentially bio-based solvents, namely 2,2,5,5-tetramethyloxolane (TMO) and 2,5-diethyl-2,5-dimethyloxolane (DEDMO), were utilized as an alternative to toxic petroleum-based hydrocarbon solvents for extraction of hentriacontane-14,16-dione from waste wheat straw waxes. This work is the first to report the application of DEDMO as a solvent for the extraction of natural products. The sustainable methodology developed in this research provided considerable advantages over previously reported systems in terms of high extraction yields, excellent selectivity towards the ß-diketones and low amounts of waste generated. DEDMO provided the highest recovery yield for all the sustainable solvents investigated, recovering 23.7% of the wax (which is a 68.8% yield of the ß-diketone). The extracted lipophilic hentriacontane-14,16-dione was utilised in combination with the sustainable solvents TMO or DEDMO to facilitate the creation of highly hydrophobic coatings. Moreover, the use of DEDMO was found to aid in the self-assembly of nano-structured tubule formation of both the unrefined wax and isolated ß-diketone. Green metric evaluation using process mass intensity (PMI), E-factor, solvent intensity (SI), and water intensity (WI) demonstrated that the described extraction procedure for hentriacontane-14,16-dione was highly sustainable and safer than the previous methodology. This sustainable manufacturing process may create the potential to valorise agricultural wastes as part of a holistic biorefinery.