RESUMEN
Li dendrites form in Li7 La3 Zr2 O12 (LLZO) solid electrolytes due to intrinsic volume changes of Li and the appearance of voids at the Li metal/LLZO interface. Bilayer dense-porous LLZO membranes make for a compelling solution of this pertinent challenge in the field of Li-garnet solid-state batteries (SSB). Lithium is thus stored in the pores of the LLZO, thereby avoiding i) dynamic changes of the anode volume and ii) the formation of voids during Li stripping due to increased surface area of the Li/LLZO interface. The dense layer then additionally reduces the probability of short circuits during cell charging. In this work, a method for producing such bilayer membranes utilizing sequential tape-casting of porous and dense layers is reported. The minimum attainable thicknesses are 8-10 µm for dense and 32-35 µm for porous layers, enabling gravimetric and volumetric energy densities of Li-garnet SSBs of 279 Wh kg-1 and 1003 Wh L-1 , respectively. Bilayer LLZO membranes in symmetrical cell configuration exhibit high critical current density up to 6 mA cm-2 and cycling stability of over 160 cycles at a current density of 0.5 mA cm-2 at an areal capacity limitation of 0.25 mAh cm-2 .
RESUMEN
Isolated one-dimensional (1-D) proton channels in a metal-organic framework, MOF-74, have been reasonably expected to show highly directional proton conductivity, although no evidence has been provided. As a result of dimensional anisotropy of the channels evenly aligned in the c-axis of MOF-74 single crystal, highly directional proton conductivity is demonstrated by using electrochemical impedance spectroscopy. In particular, single crystals treated with sulfuric acid or ammonium hydroxide displays a maximum â¼1200-fold-enhanced c-axis proton conductivity compared to its a-axis conductivity, demonstrating highly directional proton migration through the channels. Very low activation energies (e.g., 0.12 eV) for the c-axis conductivity of MOF-74 also suggest a high proton mobility that arises via Grotthuss proton transfer parallel to the channels.
RESUMEN
The activation of open coordination sites (OCSs) in metal-organic frameworks (MOFs), i.e., the removal of solvent molecules coordinated at the OCSs, is an essential step that is required prior to the use of MOFs in potential applications such as gas chemisorption, separation, and catalysis because OCSs often serve as key sites in these applications. Recently, we developed a "chemical activation" method involving dichloromethane (DCM) treatment at room temperature, which is considered to be a promising alternative to conventional thermal activation (TA), because it does not require the application of external thermal energy, thereby preserving the structural integrity of the MOFs. However, strongly coordinating solvents such as N,N-dimethylformamide (DMF), N,N-diethylformamide (DEF), and dimethyl sulfoxide (DMSO) are difficult to remove solely with the DCM treatment. In this report, we demonstrate a multiple coordination exchange (CE) process executed initially with acetonitrile (MeCN), methanol (MeOH), or ethanol (EtOH) and subsequently with DCM to achieve the complete activation of OCSs that possess strong extracoordination. Thus, this process can serve as an effective "chemical route" to activation at room temperature that does not require applying heat. To the best of our knowledge, no previous study has demonstrated the activation of OCSs using this multiple CE process, although MeOH and/or DCM has been popularly used in pretreatment steps prior to the TA process. Using MOF-74(Ni), we demonstrate that this multiple CE process can safely activate a thermally unstable MOF without inflicting structural damage. Furthermore, on the basis of in situ 1H nuclear magnetic resonance (1H NMR) and Raman studies, we propose a plausible mechanism for the activation behavior of multiple CE.
RESUMEN
The fabrication of metal-organic framework (MOF) films on conducting substrates has demonstrated great potential in applications such as electronic conduction and sensing. For these applications, direct contact of the film to the conducting substrate without a self-assembled monolayer (SAM) is a desired step that must be achieved prior to the use of MOF films. In this report, we propose an in situ strategy for the rapid one-step conversion of Cu metal into HKUST-1 films on conducting Cu substrates. The Cu substrate acts both as a conducting substrate and a source of Cu2+ ions during the synthesis of HKUST-1. This synthesis is possible because of the simultaneous reaction of an oxidizing agent and a deprotonating agent, in which the former agent dissolves the metal substrate to form Cu2+ ions while the latter agent deprotonates the ligand. Using this strategy, the HKUST-1 film could not only be rapidly synthesized within 5 min but also be directly attached to the Cu substrate. Based on microscopic studies, we propose a plausible mechanism for the growth reaction. Furthermore, we show the versatility of this in situ conversion methodology, applying it to ZIF-8, which comprises Zn2+ ions and imidazole-based ligands. Using an I2-filled HKUST-1 film, we further demonstrate that the direct contact of the MOF film to the conducting substrate makes the material more suitable for use as a sensor or electronic conductor.