RESUMEN
Developing single-crystal-based heterostructured ferroelectrics with high-performance photo-piezocatalytic activity is highly desirable to utilize large piezopotentials and more reactive charges that can trigger the desired redox reactions. To that end, a single-crystal-based (K,Na)NbO3 (KNN) microcuboid/CuO nanodot heterostructure with enhanced photo-piezocataytic activity, prepared using a facile strategy that leveraged the synergy between heterojunction formation and an intense single-crystal-based piezoelectric effect, is reported herein. The catalytic rhodamine B degrading activity of KNN/CuO is investigated under light irradiation, ultrasonication, or co-excitation with both stimulations. Compared to polycrystalline KNN powders and bare KNN single-crystals, single-crystal-based KNN/CuO exhibits a higher piezocurrent density and an optimal energy band structure, resulting in 5.23 and 2.37 times higher piezocatalytic degradation activities, respectively. Furthermore, the maximum photo-piezocatalytic rate constant (≈0.093 min-1 ) of KNN/CuO under 25 min ultrasonication and light irradiation is superior to that of other KNN-based catalysts, and 1.6 and 48.6 times higher than individual piezocatalytic and photocatalytic reaction rate constants, respectively. The excellent photo-piezocatalytic activity is attributed to the enhanced charge-carrier separation and proper alignment of band structure to the required redox levels by the appropriate p-n heterojunction and high piezoelectric potential. This report provides useful insight into the relationships between heterojunctions, piezoelectric responses, and catalytic mechanisms for single-crystal-based heterostructured catalysts.
RESUMEN
Lithium (Li) metal is a promising anode material for high-energy-density Li batteries due to its high specific capacity. However, the uneven deposition of Li metal causes significant volume expansion and safety concerns. Here, we investigate the impact of a gradient-infused Li-metal anode using silver (Ag)-decorated carbonized cellulose fibers (Ag@CC) as a three-dimensional (3D) current collector. The loading level of the gradient-infused Li-metal anode is controlled by the thermal infusion time of molten Li. In particular, a 5 s infusion time in the Ag@CC current collector creates an appropriate space with a lithiophilic surface, resulting in improved cycling stability and a reduced volume expansion rate. Moreover, integrating a 5 s Ag@CC anode with a high-capacity cathode demonstrates superior electrochemical performance with minimal volume expansion. This suggests that a gradient-infused Li-metal anode using Ag@CC as a 3D current collector represents a novel design strategy for Li-metal-based high-capacity Li-ion batteries.
RESUMEN
A Pt-nanoparticle-decorated 1T-MoS2 layer is designed as a sacrificial electrocatalyst by carbothermal shock (CTS) treatment to improve the energy efficiency and lifespan of seawater batteries. The phase transition of MoS2 crystals from 2H to metallic 1Tâinduced by the simple but potent CTS treatmentâimproves the oxygen-reduction-reaction (ORR) activity in seawater catholyte. In particular, the MoS2-based sacrificial catalyst effectively decreases the overpotential during charging via edge oxidation of MoS2, enhancing the cycling stability of the seawater battery. Furthermore, Pt nanoparticles are deposited onto CTS-MoS2 via an additional CTS treatment. The resulting specimen exhibits a significantly low charge/discharge potential gap of Δ0.39 V, high power density of 6.56 mW cm-2, and remarkable cycling stability up to â¼200 cycles (â¼800 h). Thus, the novel strategy reported herein for the preparation of Pt-decorated 1T-MoS2 by CTS treatment could facilitate the development of efficient bifunctional electrocatalysts for fabricating seawater batteries with long service life.
RESUMEN
Polyethylene terephthalate (PET) waste was depolymerized into bis(2-hydroxyethyl) terephthalate (BHET) through glycolysis with the aid of oyster shell-derived catalysts. The equilibrium yield of BHET was as high as 68.6% under the reaction conditions of mass ratios (EG to PET = 5, catalyst to PET = 0.01) at 195 °C for 1 h. Although biomass-derived Ca-based catalysts were used for PET glycolysis to obtain BHET monomers, no statistical analysis was performed to optimize the reaction conditions. Thus, in this study, we applied response surface methodology (RSM) based on three-factor Box-Behnken design (BBD) to investigate the optimal conditions for glycolysis by analyzing the independent and interactive effects of the factors, respectively. Three independent factors of interest include reaction time, temperature, and mass ratio of catalyst to PET under a fixed amount of ethylene glycol (mass ratio of EG to PET = 5) due to the saturation of the yield above the mass ratio. The quadratic regression equation was calculated for predicting the yield of BHET, which was in good agreement with the experimental data (R2 = 0.989). The contour and response surface plots showed the interaction effect between three variables and the BHET yield with the maximum average yield of monomer (64.98%) under reaction conditions of 1 wt% of mass ratio (catalyst to PET), 195 °C, and 45 min. Both the experimental results and the analyses of the response surfaces revealed that the interaction effects of reaction temperature vs. time and temperature vs. mass ratio of the catalyst to the PET were more prominent in comparison to reaction time vs. mass ratio of the catalyst to the PET.
RESUMEN
This work introduces the fabrication of a magnetic polymer bowl for enhanced catalytic activity and recyclability, which involves the synthesis of silica-coated Fe3O4 magnetic clusters, seeded dispersion polymerization using the magnetic clusters, and transformation into a bowl-like structure via a phase separation route. The additional treatment with tannic acid (TA) on the bowls allows the in situ formation of silver nanoparticles (AgNPs) on their surfaces. The openness and larger surface area of the bowls, as compared with those of other structured particles, such as spheres and flowers, enable a considerably higher immobilization of AgNPs, thus leading to an excellent catalytic reduction for 4-nitrophenol (4-NP), methylene blue (MB), and rhodamine B. Furthermore, the strong magnetic response originating from the magnetic clusters inside the bowls endows a good magnetic recovery and an excellent reusability for the repeated reduction of the organic dyes without loss of catalytic activity.
RESUMEN
A cell surface display system was developed in Pichia pastoris using the gene TIP1, encoding the glycosylphosphatidylinositol (GPI)-anchored protein of Saccharomyces cerevisiae (ScTIP). Human lactoferrin cDNA (hLf) was fused to a full-length TIP1 DNA (ScTIP ( 630 )) or a short-TIP1 fragment (ScTIP ( 120 )) encoding the 40 C-terminal amino acids of ScTIP. Both hLf-ScTIP fusion genes were expressed in P. pastoris SMD 1168. The fused protein was detected by western blotting after extraction of the lysed recombinant cells with Triton X-100, urea, and Triton X-100 plus urea, suggesting that the hLf is associated with the membrane. The localization of surface-displayed hLf was confirmed by immunofluorescence confocal microscopy and flow cytometric analysis using FITC-labeled anti-hLf antibody, suggesting that hLf was successfully located at the surface of P. pastoris. The intact recombinant cells and cell lysates showed antibacterial activity against target microorganisms, meaning that the expressed hLf was biologically active. The results indicated that the ScTIP anchoring motif is useful for cell surface display of foreign proteins in P. pastoris.