RESUMEN
The quest for better nutritious foods has encouraged novel scientific investigations to find trans-fat reduction methods. This research proposes an innovative approach for the production of healthier trans-fat-free margarine from palm oil by the use of dielectric barrier discharge (DBD) plasma technology with glycerol serving as the principal source of hydrogen. The effectiveness of DBD plasma in hydrogenating palm olein was investigated. By employing a methodical series of experiments and thorough analytical approaches, examination of the saturated fatty acid conversion experienced its iodine value (IV) reduction from 67.16 ± 0.70 to 31.61 ± 1.10 under the optimal process parameters of 1 L min-1 He flow rate, 35 W plasma discharge power, 10 mm gap size, ambient initial temperature, and 12 h reaction time with solid texture. According to the method for producing trans-fat-free margarine in the absence of a catalyst and H2 gas, the hydrogenation rate of the prepared mixture of palm olein-glycerol was remarkably improved; the trans-fat content in the produced product was zero; the efficacy of incorporating cis- and trans-isomerization was lowered, and the method has a promising industrial application prospect.
RESUMEN
This work features a new corona discharge plasma technology for de-inking yellow, blue, and red colors on various papers. This work was developed to minimize the chemical and environmental impacts of de-inking processes. A nonchemical contribution, operating at room temperature and atmospheric pressure, reduces the environmental impact of the process. The deinkability factor (DEMLab) values for all papers are determined with the optimal assessment results provided by a 36-mm variation gap at 2-min (blue) and 10-min (yellow and red) plasma exposure times, followed by applied voltages of 20 kV (yellow), 16 kV (blue), and 20 kV (red). The corona discharge plasma led to 48.58% (yellow printed paper), 64.11% (blue printed paper), and 41.11% (red printed paper) deinkability without altering the physical properties of the paper itself. The change in the tensile strength for the plasma-exposed paper was relatively little, less than 10%, compared to that of common recycling. The tensile strength of the untreated white paper was 5065 ± 487.44 N/mm2, and that of the plasma-treated printed paper was 4593 ± 248.47 N/mm2. It appears that there is little impact on the physicochemical properties of paper induced by the corona plasma treatment during the de-inking process.
RESUMEN
Adsorption is regarded as an efficient method to eliminate per- and polyfluoroalkyl substances from an aqueous solution. In the present investigation, an adsorbent based on rice husks (RHs) was successfully prepared by phosphoric acid (PA) activation and dielectric barrier discharge (DBD) plasma treatment, and it was used to adsorb perfluorooctanoic acid (PFOA) from water. The electrodes employed in the experiment were planar type. This research investigated RH surface properties and adsorption capacity before and after modification using DBD plasma. The results revealed that the He-O2 plasma modification introduced oxygen-containing functional groups and increased the PFOA removal efficiency. Increasing the oxygen content and total gas flow rate to 30 vol.% and 1.5 L/min, respectively, with 10 min of RH plasma treatment time at 100 W plasma discharge power enhanced the PFOA removal efficiency to 92.0%, while non-treated RH showed the removal efficiency of only 46.4%. The removal efficiency of the solution increased to 96.7% upon adjusting the pH to 4. The adsorption equilibrium isotherms fitted the Langmuir model, and the adsorption kinetic followed the pseudo-second-order model. The maximum adsorption capacity was 565 mg/g when the Langmuir isotherm model was applied.
RESUMEN
Changing the growth environment for microalgae can overall lead to the fundamental alteration in cellular biochemicals whilst attaching onto palm kernel expeller (PKE) waste to form adhesion complex in easing harvesting at stationary growth phase. This study had initially optimized the PKE dosage, light intensity and photoperiod in maximizing the attached microalgal productivity being attained at 0.72 g/g day. Lipid content increased progressively from pH 3 to pH 11, with the highest value observed at pH 11. Meanwhile, in terms of protein and carbohydrate contents, the highest values were obtained by cultivation medium of pH 5 with 9.92 g and 17.72 g, respectively followed by pH 7 with 9.16 g and 16.36 g, respectively. Moreover, the findings also suggested that the low pH mediums utilized polar interactions in the formation of complexes between PKE and microalgae, whereas at higher pH levels, the non-polar interactions became more significant. The work of attachment was thermodynamically favourable towards the attachment formation with values greater than zero which was also aligned with the microscopic surface topography, i.e., revealing a clustering pattern of microalgae colonizing the PKE surface. These findings contribute to comprehensive understanding of optimizing growth condition and harvesting strategy of attached microalgae in attaining the cellular biochemical components, facilitating the development of efficient and sustainable bioresource utilization.
Asunto(s)
Microalgas , BiomasaRESUMEN
The depletion of fossil fuel sources and increase in energy demands have increased the need for a sustainable alternative energy source. The ability to produce hydrogen from microalgae is generating a lot of attention in both academia and industry. Due to complex production procedures, the commercial production of microalgal biohydrogen is not yet practical. Developing the most optimum microalgal hydrogen production process is also very laborious and expensive as proven from the experimental measurement. Therefore, this research project intended to analyse the random time series dataset collected during microalgal hydrogen productions while using various low thermally pre-treated palm kernel expeller (PKE) waste via machine learning (ML) approach. The analysis of collected dataset allowed the derivation of an enhanced kinetic model based on the Gompertz model amidst the dark fermentative hydrogen production that integrated thermal pre-treatment duration as a function within the model. The optimum microalgal hydrogen production attained with the enhanced kinetic model was 387.1 mL/g microalgae after 6 days with 1 h thermally pre-treated PKE waste at 90 °C. The enhanced model also had better accuracy (R2 = 0.9556) and net energy ratio (NER) value (0.71) than previous studies. Finally, the NER could be further improved to 0.91 when the microalgal culture was reused, heralding the potential application of ML in optimizing the microalgal hydrogen production process.
Asunto(s)
Microalgas , Fermentación , Hidrógeno/análisis , Combustibles Fósiles , Biocombustibles , BiomasaRESUMEN
More energy is needed nowadays due to global population growth. Concurrently, sewage sludge generation has also increased steadily stemming from the inevitable urbanization. As such, black soldier fly larvae (BSFL) can be potentially deployed to solve both issues. This paper investigates the environmental sustainability of biodiesel production derived from sludge-fed BSFL feedstock. A cradle-to-gate life cycle assessment (LCA) was performed through SimaPro software utilizing the ReCiPe 2016 Midpoint (H) and Endpoint (H) methods. The entire LCA covered 3 main stages, including the thermal pre-treatment of sludge, BSFL rearing and processing, and lastly lipid extraction and biodiesel production. LCA showed that the sludge pre-treatment stage had the highest environmental impact, while BSFL rearing and processing had the least due to the suitable geographical climate. Electricity usage during the pre-treatment stage was the main contributing component, followed by chemical usage during biodiesel production. After normalizing, it was observed that land occupation, marine ecotoxicity, freshwater ecotoxicity and freshwater eutrophication were more impactful than the commonly studied global warming potential (GWP). Lipid content and biodiesel conversion efficiency were determined as the sensitive factors which could influence the LCA outcome. In comparison with other types of biodiesel, BSFL biodiesel had a milder impact in terms of climate change, land occupation, terrestrial acidification, marine and freshwater eutrophication. Furthermore, this biological reduction of sludge through BSFL valorization avoided sludge landfilling, which reduced up to 100 times GWP. Therefore, sludge-fed BSFL biodiesel production is an environmentally-sound and highly potential solution that should be investigated comprehensively.
Asunto(s)
Dípteros , Aguas del Alcantarillado , Animales , Larva , Biocombustibles , LípidosRESUMEN
Hydrogen is a clean and green biofuel choice for the future because it is carbon-free, non-toxic, and has high energy conversion efficiency. In exploiting hydrogen as the main energy, guidelines for implementing the hydrogen economy and roadmaps for the developments of hydrogen technology have been released by several countries. Besides, this review also unveils various hydrogen storage methods and applications of hydrogen in transportation industry. Biohydrogen productions from microbes, namely, fermentative bacteria, photosynthetic bacteria, cyanobacteria, and green microalgae, via biological metabolisms have received significant interests off late due to its sustainability and environmentally friendly potentials. Accordingly, the review is as well outlining the biohydrogen production processes by various microbes. Furthermore, several factors such as light intensity, pH, temperature and addition of supplementary nutrients to enhance the microbial biohydrogen production are highlighted at their respective optimum conditions. Despite the advantages, the amounts of biohydrogen being produced by microbes are still insufficient to be a competitive energy source in the market. In addition, several major obstacles have also directly hampered the commercialization effors of biohydrogen. Thus, this review uncovers the constraints of biohydrogen production from microbes such as microalgae and offers solutions associated with recent strategies to overcome the setbacks via genetic engineering, pretreatments of biomass, and introduction of nanoparticles as well as oxygen scavengers. The opportunities of exploiting microalgae as a suastainable source of biohydrogen production and the plausibility to produce biohydrogen from biowastes are accentuated. Lastly, this review addresses the future perspectives of biological methods to ensure the sustainability and economy viability of biohydrogen production.
Asunto(s)
Cianobacterias , Microalgas , Fermentación , Cianobacterias/metabolismo , Hidrógeno/análisis , Hidrógeno/metabolismo , Biocombustibles , BiomasaRESUMEN
The capacity to maximize the proliferation of microalgal cells by means of topologically textured organic solid surfaces under various pH gave rise to the fundamental biophysical analysis of cell-surface attachment in this study. The substrate used in analysis was palm kernel expeller (PKE) in which the microalgal cells had adhered onto its surface. The findings elucidated the relevance of surface properties in terms of surface wettability and surface energy in relation to the attached microalgal growth with pH as the limiting factor. The increase in hydrophobicity of PKE-microalgae attachment was able to facilitate the formation of biofilm better. The pH 5 and pH 11 were found to be the conditions with highest and lowest microalgal growths, respectively, which were in tandem with the highest contact angle value at pH 5 and conversely for pH 11. The work of attachment (Wcs) had supported the derived model with positive values being attained for all the pH conditions, corroborating the thermodynamic feasibility. Finally, this study had unveiled the mechanism of microalgal attachment onto the surface of PKE using the aid of extracellular polymeric surfaces (EPS) from microalgae. Also, the hydrophobic nature of PKE enabled excellent attachment alongside with nutrients for microalgae to grow and from layer-by-layer (LbL) assembly. This assembly was then isolated using organosolv method by means of biphasic solvents, namely, methanol and chloroform, to induce detachment.
Asunto(s)
Chlorella vulgaris , Microalgas , Propiedades de Superficie , Interacciones Hidrofóbicas e Hidrofílicas , Biopelículas , BiomasaRESUMEN
Endocrine disrupting compounds (EDCs) are extensively found in the environment and severely impacting human health. In addressing this issue, the beta-cyclodextrin crosslinked citric acid (BCD-CA) had been previously employed in membrane-protected micro-solid phase extraction for sequestering EDCs from water medium; and the findings revealed that BCD-CA possessed a selectivity property. On that account, the potential of BCD-CA towards competitive adsorption of selected EDCs was investigated in terms of adsorption mechanism and selectivity property. Factors that affected the removal efficiencies such as sample pH, sorbent dosage, contact time and initial concentration were evaluated. The characterization results revealed that the carbon percentage of BCD-CA had increased by 2.04%, while the hydrogen percentage had reduced by 1.83%, signifying the successful crosslinking of BCD-CA. Besides, the amount of active BCD was calculated to be 3.2 × 10-7 mol, while the amount of carboxyl group was 2.48 × 10-5 mol per 4 mg of BCD-CA. Moreover, BCD-CA was stable in an aqueous medium with the zeta potential obtained at -36.5 mV and had a high-water retention capacity (â¼150%). The competitive adsorption mechanism by BCD-CA with EDCs followed the pseudo-second-order kinetics and Freundlich isotherm, suggesting that the adsorption process was dominated by chemisorption on the heterogeneous surface of the adsorbent. Thermodynamic results revealed that adsorption of 4-tert-octylphenol had the most negative ΔG value, indicating most favorable to be adsorbed by BCD-CA as opposed to triclosan and bisphenol A, which was coherent with the apparent formation constant results. These unique properties manifested the practicality of BCD-CA as a selective adsorbent to detect and remove EDCs from the water medium.
Asunto(s)
Disruptores Endocrinos , Triclosán , beta-Ciclodextrinas , Humanos , Polipropilenos , Ácido Cítrico , Extracción en Fase Sólida , beta-Ciclodextrinas/química , Agua/química , Carbono , HidrógenoRESUMEN
The ever-increasing quantity of greenhouse gases in the atmosphere can be attributed to the rapid increase in the world population as well as the expansion of globalization. Hence, achieving carbon neutrality by 2050 stands as a challenging task to accomplish. Global industrialization had necessitated the need to enhance the current production systems to reduce greenhouse gases emission, whilst promoting the capture of carbon dioxide from atmosphere. Hydrogen is often touted as the fuel of future via substituting fossil-based fuels. In this regard, renewable hydrogen happens to be a niche sector of novel technologies in achieving carbon neutrality. Microalgae-based biohydrogen technologies could be a sustainable and economical approach to produce hydrogen from a renewable source, while simultaneously promoting the absorption of carbon dioxide. This review highlights the current perspectives of biohydrogen production as an alternate source of energy. In addition, future challenges associated with biohydrogen production at large-scale application, storage and transportation are included. Key technologies in producing biohydrogen are finally described in building a carbon-neutral future.
RESUMEN
Albeit the biodiesel production from suspended microalgal system has gained immense interests in recent years, the domineering limitation of being economically infeasible has hindered this technology from partaking into a large-scale operation. To curtail this issue, attached growth system had been introduced by various studies; however, those were still unable to alleviate the socio-economic challenges faced in commercializing the microalgal biomass production. Thus, this study had developed a novel approach in cultivating-cum-harvesting attached Chlorella vulgaris sp. microalgae, whilst using solid organic waste of palm kernel expeller (PKE) as the supporting and alimentation material for microalgal biofilm formation. The effects of three variables, namely, PKE dosage, light intensity, and photoperiod, were initially modelled and later optimized using Response Surface Methodology tool. The derived statistical models could predict the growth performances of attached microalgal biomass and lipid productivity. The optimum growing condition was attained at PKE dosage of 5.67 g/L, light intensity of 197 µmol/m2 s and photoperiod of 8 light and 16 dark hours/cycle, achieving the microalgal density and lipid content of 9.87 ± 0.05 g/g and 3.39 ± 0.28 g/g, respectively, with lipid productivity of 29.6 mg/L day. This optimum condition had led to the intensification of biodiesel quality with a high percentage of monounsaturated fatty acid, i.e., oleic acid (C18:1), encompassing 81.86% of total fatty acid methyl ester components. Given that the positive acquisition of PKE as an excellent supporting material in enhancing the microalgal density and lipid productivity that had resulted in the commercially viable biodiesel quality, this study served as a novel revolution in augmenting the microalgae and solid waste utilities for sustainable energy generation.
Asunto(s)
Chlorella vulgaris , Microalgas , Biocombustibles , Biomasa , Ácidos GrasosRESUMEN
Endocrine disruptor compounds (EDCs) such as plasticisers, surfactants, pharmaceutical products, personal care products and pesticides are frequently released into the environmental waters. Therefore, a sensitive and environmentally friendly method is entailed to quantify these compounds at their trace level concentrations. This study encapsulated the ß-cyclodextrin crosslinked with citric acid in a polypropylene membrane protected-µ-solid phase extraction (BCD-CA µ-SPE) device for preconcentrating the EDCs (triclosan, triclocarban, 2-phenylphenol, 4-tert-octylphenols and bisphenol A) in real water samples before the analysis by high-performance liquid chromatography. FT-IR and TGA results indicated that BCD-CA was successfully synthesised with the formation of ester linkage (1078.33 cm-1) and O-H stretching from carboxylic acid (3434.70 cm-1) with higher thermal stability as compared with native CD with the remaining weight above 72.1% at 500 °C. Several critical parameters such as the sorbent loading, type and amount of salts, extraction time, sample volume, sample pH, type and volume of desorption solvents and desorption time were sequentially optimised and statistically validated. Under the optimum condition, the use of BCD-CA µ-SPE device had manifested good linearity (0.5-500 µg L-1) with the determination of the coefficient range of 0.9807-0.9979. The p-values for the F-test and t-test (6.60 × 10-8 - 1.77 × 10-5) were lesser than 0.05 and low detection limits ranging from 0.27 to 0.84 µg L-1 for all studied EDCs. The developed technique was also successfully applied for EDC analyses in four distinct real water samples, namely, wastewater, river water, tap water and mineral water, with good EDCs recoveries (80.2%-99.9%), low relative standard deviations (0.1%-3.8%, n = 3) with enrichment factor ranging from 9 to 82 folds. These results signified the potential of the BCD-CA µ-SPE device as an efficient, sensitive, and environmentally friendly approach for analyzing EDCs.
Asunto(s)
Disruptores Endocrinos , Contaminantes Químicos del Agua , beta-Ciclodextrinas , Cromatografía Líquida de Alta Presión/métodos , Ácido Cítrico , Disruptores Endocrinos/análisis , Límite de Detección , Polipropilenos/análisis , Extracción en Fase Sólida/métodos , Espectroscopía Infrarroja por Transformada de Fourier , Agua/química , Contaminantes Químicos del Agua/análisisRESUMEN
Being the second-largest country in the production of palm oil, Malaysia has a massive amount of palm kernel expeller (PKE) leftover. For that purpose, black soldier fly larvae (BSFL) are thus employed in this study to valorize the PKE waste. More specifically, this work elucidated the effects of the pre-fermentation of PKE via different amounts of Rhizopus oligosporus to enhance PKE palatability for the feeding of BSFL. The results showed that fermentation successfully enriched the raw PKE and thus contributed to the better growth of BSFL. BSFL grew to be 34% heavier at the optimum inoculum volume of 0.5 mL/10 g dry weight of PKE as compared to the control. Meanwhile, excessive fungal inoculum induced competition between BSFL and R. oligosporus, resulting in a reduction in BSFL weight. Under optimum feeding conditions, BSFL also registered the highest lipid yield (24.7%) and protein yield (44.5%). The biodiesel derived from BSFL lipid had also shown good compliance with the European biodiesel standard EN 14214. The high saturated fatty acid methyl esters (FAMEs) content (C12:0, C14:0, C16:0) in derived biodiesel made it highly oxidatively stable. Lastly, the superior degradation rate of PKE executed by BSFL further underpinned the sustainable conversion process in attaining valuable larval bioproducts.
RESUMEN
Black soldier fly larvae (BSFL) have been deployed to valorize various organic wastes. Nonetheless, its growth rate whilst being offered with waste activated sludge (WAS) is not promising, likely by virtue of the presence of extracellular polymeric substances' structure in WAS. In this work, the WAS were first thermally pre-treated under different treatment temperatures and durations before being administered as the feeding substrates for BSFL. The results showed the thermal pre-treatment could improve WAS palatability and subsequently, enhance the growth of BSFL especially after the pre-treatments at 75 °C and above. The highest larva weight gained was recorded at 2.16 mg/larva for the WAS sample being pre-treated at 90 °C and 16 h. Furthermore, the samples pre-treated above 75 °C also achieved higher degradation rates, indicating that the 75 °C was a threshold temperature to effectively hydrolyze the WAS. The changes of WAS characteristics, namely, (i) soluble chemical oxygen demand (SCOD), (ii) soluble carbohydrate, (iii) soluble protein, (iv) humic substances and (v) total soluble protein and humic substances, after the thermal pre-treatments were also studied in correlating with the BSFL growth. Accordingly, a model was successfully developed with the highest R2 value attained at 0.95, evidencing the SCOD was the most suitable WAS characteristic to accurately predict the BSFL growth behavior.
Asunto(s)
Dípteros , Aguas del Alcantarillado , Animales , Sustancias Húmicas , Larva , NutrientesRESUMEN
Low temperature thermal pre-treatment is a low-cost method to break down the structure of extracellular polymeric substances in waste activated sludge (WAS) while improving the sludge biodegradability. However, previous models on low temperature thermal pre-treatment did not adequately elucidate the behaviour of sludge hydrolysis process for the duration ranging from 5 to 9 h. Therefore, this work had developed an inclusive functional model to describe the kinetics of sludge hydrolysis for a wide range of treatment conditions (30 °C-90 °C within 0 and 16 h). As compared with treatment duration, the treatment temperature played a greater impact in solubilizing WAS. Accordingly, the 90 °C treatment had consistently produced WAS with the highest degree of solubility. Nonetheless, the mediocre discrepancies between 90 °C and 75 °C may challenge the practicality of increasing the treatment temperatures beyond 75 °C. The effects of treatment duration on soluble chemical oxygen demand, soluble carbohydrate and soluble protein were only significant during the first 4 h, except for humic substances release that continued to increase with treatment duration. Finally, a good fit with R2 > 0.95 was achieved using an inclusive multivariate non-linear model, substantiating the functionality to predict the kinetics of sludge hydrolysis at arbitrary treatment conditions.
Asunto(s)
Dinámicas no Lineales , Aguas del Alcantarillado , Anaerobiosis , Hidrólisis , Cinética , Temperatura , Eliminación de Residuos LíquidosRESUMEN
Partially hydrogenated fatty acid methyl ester (H-FAME) is conventionally produced through partial hydrogenation under high pressure and elevated temperature in the presence of a catalyst. Herein, a novel green, catalyst-free, non-thermal and atmospheric pressure dielectric barrier discharge (DBD) plasma was employed instead of a conventional method to hydrogenate palm FAME. H-FAME became more saturated with the conversion of C18:2 and C18:3 of 47.4 and 100%, respectively, at 100 W input power, 1 mm gas-filled gap size and 80% H2 in the mixed gas at room temperature for 5 h, causing a reduction of the iodine value from 50.2 to 43.5. Oxidation stability increased from 12.8 to 20 h while a cloud point changed from 13.5 to 16 °C. Interestingly, DBD plasma hydrogenation resulted in no trans-fatty acid formation which provided a positive effect on the cloud point. This green DBD plasma system showed a superior performance to a conventional catalytic reaction. It is an alternative method that is safe from explosion due to the mild operating condition, as well as being highly environmentally friendly by reducing waste and energy utilization from the regeneration process required for a catalytic process. This novel green plasma hydrogenation technique could also be applied to other liquid-based processes.
RESUMEN
Fatty acid methyl esters (FAMEs) are sustainable biofuel that can alleviate high oil costs and environmental impacts of petroleum-based fuel. A modified 1200 W high-efficiency food blender was employed for continuous transesterification of various refined vegetable oils and waste cooking oil (WCO) using sodium hydroxide as a homogeneous catalyst. The following factors have been investigated on their effects on FAME yield: baffles, reaction volume, total reactant flow rate, methanol-oil molar ratio, catalyst concentration and reaction temperature. Results indicated that the optimal conditions were: 2000 mL reaction volume, 50 mL/min total flow rate, 1% and 1.25% catalyst concentration for refined palm oil and WCO, respectively, 6:1 methanol-to-oil molar ratio and 62-63 °C, obtaining yield efficiency over 96.5% FAME yield of 21.14 × 10-4 g/J (for palm oil) and 19.39 × 10-4 g/J (for WCO). All the properties of produced FAMEs meet the EN 14214 and ASTM D6751 standards. The modified household food blender could be a practical and low-cost alternative biodiesel production apparatus for continuous biodiesel production for small communities in remote areas.
RESUMEN
Sewage sludge has long been regarded as a hazardous waste by virtue of the loaded heavy metals and pathogens. Recently, more advanced technologies are introduced to make use of the nutrients from this hazardous sludge. Successful recovery of sludge's carbon content could significantly convert waste to energy and promote energy sustainability. Meanwhile, the recovery of nitrogen and trace minerals allows the production of fertilizers. This review is elucidating the performances of modern thermal treatment technologies in recovering resources from sewage sludge while reducing its environmental impacts. Exhaustive investigations show that most modern technologies are capable of recovering sludge's carbon content for energy generation. Concurrently, the technologies could as well stabilize heavy metals, destroy harmful pathogens, and reduce the volume of sludge to minimize the environmental impacts. Nevertheless, the high initial investment cost still poses a huge hurdle for many developing countries. Since the initial investment cost is inevitable, the future works should focus on improving the profit margin of thermal technologies; so that it would be more financially attractive. This can be done through process optimization, improved process design as well as the use of suitable co-substrates, additives, and catalyst as propounded in the review.
Asunto(s)
Metales Pesados , Aguas del Alcantarillado , Fertilizantes , NitrógenoRESUMEN
The increase of annual organic wastes generated worldwide has become a major problem for many countries since the mismanagement could bring about negative effects on the environment besides, being costly for an innocuous disposal. Recently, insect larvae have been investigated to valorize organic wastes. This entomoremediation approach is rising from the ability of the insect larvae to convert organic wastes into its biomass via assimilation process as catapulted by the natural demand to complete its lifecycle. Among the insect species, black soldier fly or Hermetia illucens is widely researched since the larvae can grow in various environments while being saprophagous in nature. Even though black soldier fly larvae (BSFL) can ingest various decay materials, some organic wastes such as sewage sludge or lignocellulosic wastes such as waste coconut endosperm are destitute of decent nutrients that could retard the BSFL growth. Hence, blending with nutrient-rich low-cost substrates such as palm kernel expeller, soybean curd residue, etc. is employed to fortify the nutritional contents of larval feeding substrates prior to administering to the BSFL. Alternatively, microbial fermentation can be adopted to breakdown the lignocellulosic wastes, exuding essential nutrients for growing BSFL. Upon reaching maturity, the BSFL can be harvested to serve as the protein and lipid feedstock. The larval protein can be made into insect meal for farmed animals, whilst the lipid source could be extracted and transesterified into larval biodiesel to cushion the global energy demands. Henceforth, this review presents the influence of various organic wastes introduced to feed BSFL, targeting to reduce wastes and producing biochemicals from mature larvae through entomoremediation. Modification of recalcitrant organic wastes via fermentation processes is also unveiled to ameliorate the BSFL growth. Lastly, the sustainable applications of harvested BSFL biomass are as well covered together with the immediate shortcomings that entail further researches.
Asunto(s)
Dípteros , Simuliidae , Animales , Biocombustibles , Larva , Lípidos , Aguas del AlcantarilladoRESUMEN
This work aims to enhance the photocatalytic antibacterial performance of plastics according to the JIS Z 2801:2010 standard, and to determine their mechanical properties by studying: (i) the influence of calcination on titanium dioxide (TiO2); (ii) modification with different TiO2 concentrations, and; (iii) the effect of silane as a coupling agent. Acrylonitrile-butadiene-styrene plastics (ABS) and Escherichia coli (E. coli) were chosen as the model plastic and bacteria, respectively. The 500 °C calcined TiO2 successfully provided the best photoantibacterial activity, with an approximately 62% decrease of E. coli colony counts following 30 min of exposure. Heat treatment improved the crystallinity of anatase TiO2, resulting in low electron-hole recombination, while effectively adsorbing reactants on the surface. ABS with 500 °C-calcined TiO2 at the concentration of 1 wt % gave rise to the highest performance due to the improved distribution of TiO2. At this point, blending silane coupling agent could further improve the efficacy of photoantibacterial activity up to 75% due to greater interactions with the polymer matrix. Moreover, it could promote a 1.6-fold increase of yield strength via increased adherent bonding between TiO2 and the ABS matrix. Excellent photocatalytic and material stability can be achieved, with constant photocatalytic efficiency remaining for up to five reuse cycles without loss in the yield strength.