Studying Surface Chemistry of Mixed Conducting Perovskite Oxide Electrodes with Synchrotron-Based Soft X-rays.

A fundamental understanding of the electrochemical reactions and surface chemistry at the solid-gas interface in situ and operando is critical for electrode materials applied in electrochemical and catalytic applications. Here, the surface reactions and surface composition of a model of mixed ionic and electronic conducting (MIEC) perovskite oxide, (La0.8Sr0.2)0.95Cr0.5Fe0.5O3-δ (LSCrF8255), were investigated in situ using synchrotron-based near-ambient pressure (AP) X-ray photoelectron spectroscopy (XPS) and near-edge X-ray absorption fine-structure spectroscopy (NEXAFS). The measurements were conducted with a surface temperature of 500 °C under 1 mbar of dry oxygen and water vapor, to reflect the implementation of the materials for oxygen reduction/evolution and H2O electrolysis in the applications such as solid oxide fuel cell (SOFC) and electrolyzers. Our direct experimental results demonstrate that, rather than the transition metal (TM) cations, the surface lattice oxygen is the significant redox active species under both dry oxygen and water vapor environments. It was proven that the electron holes formed in dry oxygen have a strong oxygen character. Meanwhile, a relatively higher concentration of surface oxygen vacancies was observed on the sample measured in water vapor. We further showed that in water vapor, the adsorption and dissociation of H2O onto the perovskite surface were through forming hydroxyl groups. In addition, the concentration of Sr surface species was found to increase over time in dry oxygen due to Sr surface segregation, with the presence of oxygen holes on the surface serving as an additional driving force. Comparatively, less Sr contents were observed on the sample in water vapor, which could be due to the volatility of Sr(OH)2. A secondary phase was also observed, which exhibited an enrichment in B-site cations, particularly in Fe and relatively in Cr, and a deficiency in A-site cation, notably in La and relatively in Sr. The findings and methodology of this study allow for the quantification of surface defect chemistry and surface composition evolution, providing crucial understanding and design guidelines in the electrocatalytic activity and durability of electrodes for efficient conversions of energy and fuels.

Electronic and ionic effects of sulphur and other acidic adsorbates on the surface of an SOFC cathode material.

The effects of sulphur adsorbates and other typical solid oxide fuel cell (SOFC) poisons on the electronic and ionic properties of an SrO-terminated (La,Sr)CoO3 (LSC) surface and on its oxygen exchange kinetics have been investigated experimentally with near ambient pressure X-ray photoelectron spectroscopy (NAP-XPS), low energy ion scattering (LEIS) and impedance spectroscopy as well as computationally with density functional theory (DFT). The experiment shows that trace amounts of sulphur in measurement atmospheres form SO2- 4 adsorbates and strongly deactivate a pristine LSC surface. They induce a work function increase, indicating a changing surface potential and a surface dipole. DFT calculations reveal that the main participants in these charge transfer processes are not sub-surface transition metals, but surface oxygen atoms. The study further shows that sulphate adsorbates strongly affect oxygen vacancy formation energies in the LSC (sub-)surface, thus affecting defect concentrations and oxygen transport properties. To generalize these results, the investigation was extended to other acidic oxides which are technologically relevant as SOFC cathode poisons, such as CO2 and CrO3. The results unveil a clear correlation of work function changes and redistributed charge with the Smith acidity of the adsorbed oxide and clarify fundamental mechanistic details of atomic surface modifications. The impact of acidic adsorbates on various aspects of the oxygen exchange reaction rate is discussed in detail.

Self-diffusion in garnet-type Li7La3Zr2O12 solid electrolytes.

Tetragonal garnet-type Li7La3Zr2O12 is an important candidate solid electrolyte for all-solid-state lithium ion batteries because of its high ionic conductivity and large electrochemical potential window. Here we employ atomistic simulation methods to show that the most favourable disorder process in Li7La3Zr2O12 involves loss of Li2O resulting in lithium and oxygen vacancies, which promote vacancy mediated self-diffusion. The activation energy for lithium migration (0.45 eV) is much lower than that for oxygen (1.65 eV). Furthermore, the oxygen migration activation energy reveals that the oxygen diffusion in this material can be facilitated at higher temperatures once oxygen vacancies form.

Surface Restructuring of Thin-Film Electrodes Based on Thermal History and Its Significance for the Catalytic Activity and Stability at the Gas/Solid and Solid/Solid Interfaces.

Electrodes in solid-state energy devices are subjected to a variety of thermal treatments, from film processing to device operation at high temperatures. All these treatments influence the chemical activity and stability of the films, as the thermally induced chemical restructuring shapes the microstructure and the morphology. Here, we investigate the correlation between the oxygen reduction reaction (ORR) activity and thermal history in complex transition metal oxides, in particular, La0.6Sr0.4CoO3-δ (LSC64) thin films deposited by pulsed laser deposition. To this end, three ∼200 nm thick LSC64 films with different processing and thermal histories were studied. A variety of surface-sensitive elemental characterization techniques (i.e., low-energy ion scattering, X-ray photoelectron spectroscopy, and secondary ion mass spectrometry) were employed to thoroughly investigate the cationic distribution from the outermost surface to the film/substrate interface. Moreover, electrochemical impedance spectroscopy was used to study the activity and the stability of the films. Our investigations revealed that, despite the initial comparable ORR activity at 600 °C, the degradation rates of the films differed by twofold in the long-term stability tests at 500 °C. Here, we emphasize the importance of processing and thermal history in the elemental surface distribution, especially for the stability of LSC64 electrodes and propose that they should be considered as among the main pillars in the design of active surfaces.

A CO2 -Tolerant Perovskite Oxide with High Oxide Ion and Electronic Conductivity.

Mixed ionic-electronic conductors (MIECs) that display high oxide ion conductivity (σo ) and electronic conductivity (σe ) constitute an important family of electrocatalysts for a variety of applications including fuel cells and oxygen separation membranes. Often MIECs exhibit sufficient σe but inadequate σo . It has been a long-standing challenge to develop MIECs with both high σo and stability under device operation conditions. For example, the well-known perovskite oxide Ba0.5 Sr0.5 Co0.8 Fe0.2 O3- δ (BSCF) exhibits exceptional σo and electrocatalytic activity. The reactivity of BSCF with CO2 , however, limits its use in practical applications. Here, the perovskite oxide Bi0.15 Sr0.85 Co0.8 Fe0.2 O3- δ (BiSCF) is shown to exhibit not only exceptional bulk transport properties, with a σo among the highest for known MIECs, but also high CO2 tolerance. When used as an oxygen separation membrane, BiSCF displays high oxygen permeability comparable to that of BSCF and much higher stability under CO2 . The combination of high oxide transport properties and CO2 tolerance in a single-phase MIEC gives BiSCF a significant advantage over existing MIECs for practical applications.

Oxygen transport and surface exchange mechanisms in LSCrF-ScCeSZ dual-phase ceramics.

For the mechanisms by which the oxygen gets incorporated in a dual-phase composite system, three hypotheses, i.e. cation inter-diffusion, spillover type and self-cleaning of the perovskite-structured phase, have been provided in the literature. However, experimentally a consensus on the most likely mechanism is yet to be reached. In this work, a specially fused sample of the lanthanum strontium chromium ferrite (LSCrF)-scandia/ceria-stabilised zirconia (ScCeSZ) dual-phase material was investigated. Among the three potential mechanisms, no obvious cation inter-diffusion was firstly observed. A cleaner surface of the ScCeSZ phase was confirmed in the fused sample than in the isolated ScCeSZ single-phase sample while impurity layers were clearly observed on the LSCrF surface, suggesting the cleaning effect from the perovskite. However, more evidence implies that the cleaning effect is not the only reason for the synergistic effects between these two phases. Observations via SIMS analysis lend strong support to the 'spillover-type' mechanism as the oxygen isotopic fraction on the surface of the ScCeSZ increased compared to the isolated single-phase and as the distance to the heterojunction increases, the oxygen isotopic fraction decreases. Moreover, oxygen depleted layers were clearly seen on the top layers of the LSCrF surface which may be associated with the higher oxygen diffusivity in the surface/sub-surface layers, oxygen grain boundary fast diffusion and the impurities on the perovskite phase. For this sample, a combination of 'spillover' and 'self-cleaning' type mechanisms is suggested to be the potential possibility while the contribution from the cation inter-diffusion for this specific sample is proven to be low.

Unveiling the Outstanding Oxygen Mass Transport Properties of Mn-Rich Perovskites in Grain Boundary-Dominated La0.8Sr0.2(Mn1-x Co x )0.85O3±Î´ Nanostructures.

Ion transport in solid-state devices is of great interest for current and future energy and information technologies. A superior enhancement of several orders of magnitude of the oxygen diffusivity has been recently reported for grain boundaries in lanthanum-strontium manganites. However, the significance and extent of this unique phenomenon are not yet established. Here, we fabricate a thin film continuous composition map of the La0.8Sr0.2(Mn1-x Co x )0.85O3±Î´ family revealing a substantial enhancement of the grain boundary oxygen mass transport properties for the entire range of compositions. Through isotope-exchange depth profiling coupled with secondary ion mass spectroscopy, we show that this excellent performance is not directly linked to the bulk of the material but to the intrinsic nature of the grain boundary. In particular, the great increase of the oxygen diffusion in Mn-rich compositions unveils an unprecedented catalytic performance in the field of mixed ionic-electronic conductors. These results present grain boundaries engineering as a novel strategy for designing highly performing materials for solid-state ionics-based devices.

Electrical conductivity and oxygen diffusion behaviour of the (La0.8Sr0.2)0.95CrxFe1-xO3-δ (x = 0.3, 0.5 and 0.7) A-site deficient perovskites.

Lanthanum strontium chromite ferrite ((La0.8Sr0.2)0.95CrxFe1-xO3-δ, LSCrF) pellets with 5% A-site deficiency were fabricated and the electrical conductivity and oxygen diffusion behaviour with different Cr substitution levels (x = 0.3, 0.5 and 0.7) were investigated. As the Cr content increased, the electrical conductivity increased and then a maximum value was achieved at x = 0.7. In the oxygen diffusion studies, all the measured materials present good surface exchange rates (>9 × 10-8 cm s-1 at 900 °C) while the bulk diffusivity of the investigated materials decreased as the Cr substitution level increased: at 900 °C the oxygen diffusion coefficients of the LSCrF materials (x = 0.3, 0.5 and 0.7) are 1.1 × 10-10 cm2 s-1, 3.7 × 10-12 cm2 s-1 and 8.6 × 10-13 cm2 s-1, respectively. Oxygen diffusion in the perovskite materials (LSCrF) is shown to be bulk diffusion limited and it was found that analysis on this type of material using the line scan mode in Time-of-Flight Secondary Ion Mass Spectrometry may result in significant underestimation of the surface exchange coefficient due to the oxygen saturation, while the depth profile mode provides more reliable results but the obtained surface exchange coefficients may also only reach a lower limit. Moreover, fast grain boundary diffusion behaviour was observed in the LSCrF (x = 0.7) material and the Le Claire, and Chung and Wuensch approximations were applied to analyse the oxygen diffusion profiles. For this material, the two approximations provided similar results for the grain boundary product (Dgbδ) and under the assumption that the width of a grain boundary is on the nanometre scale, the oxygen diffusion coefficient of the grain boundaries was about 3-4 orders of magnitude higher than that of the bulk at temperatures ≤900 °C.

Interface Effects on the Ionic Conductivity of Doped Ceria-Yttria-Stabilized Zirconia Heterostructures.

Multilayered heterostructures of Ce0.85Sm0.15O2-δ and Y0.16Zr0.92O2-δ of a high crystallographic quality were fabricated on (001)-oriented MgO single crystal substrates. Keeping the total thickness of the heterostructures constant, the number of ceria-zirconia bilayers was increased while reducing the thickness of each layer. At each interface Ce was found primarily in the reduced, 3+ oxidation state in a layer extending about 2 nm from the interface. Concurrently, the conductivity decreased as the thickness of the layers was reduced, suggesting a progressive confinement of the charge transport along the YSZ layers. The comparative analysis of the in-plane electrical characterization suggests that the contribution to the total electrical conductivity of these interfacial regions is negligible. For the smallest layer thickness of 2 nm the doped ceria layers are electrically insulating and the ionic transport only occurs through the zirconia layers. This is explained in terms of a reduced mobility of the oxygen vacancies in the highly reduced ceria.

The effects of lattice strain, dislocations, and microstructure on the transport properties of YSZ films.

Enhanced conductivity in YSZ films has been of substantial interest over the last decade. In this paper we examine the effects of substrate lattice mismatch and film thickness on the strain in YSZ films and the resultant effect on the conductivity. 8 mol% YSZ films have been grown on MgO, Al2O3, LAO and NGO substrates, thereby controlling the lattice mismatch at the film/substrate interface. The thickness of the films was varied to probe the interfacial contribution to the transport properties, as measured by impedance spectroscopy and tracer diffusion. No enhancement in the transport properties of any of the films was found over single crystal values, and instead the effects of lattice strain were found to be minimal. The interfaces of all films were more resistive due to a heterogeneous distribution of grain boundaries, and no evidence for enhanced transport down dislocations was found.

Back-exchange: a novel approach to quantifying oxygen diffusion and surface exchange in ambient atmospheres.

A novel two-step Isotopic Exchange (IE) technique has been developed to investigate the influence of oxygen containing components of ambient air (such as H2O and CO2) on the effective surface exchange coefficient (k*) of a common mixed ionic electronic conductor material. The two step 'back-exchange' technique was used to introduce a tracer diffusion profile, which was subsequently measured using Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS). The isotopic fraction of oxygen in a dense sample as a function of distance from the surface, before and after the second exchange step, could then be used to determine the surface exchange coefficient in each atmosphere. A new analytical solution was found to the diffusion equation in a semi-infinite domain with a variable surface exchange boundary, for the special case where D* and k* are constant for all exchange steps. This solution validated the results of a numerical, Crank-Nicolson type finite-difference simulation, which was used to extract the parameters from the experimental data. When modelling electrodes, D* and k* are important input parameters, which significantly impact performance. In this study La0.6Sr0.4Co0.2Fe0.8O3-δ (LSCF6428) was investigated and it was found that the rate of exchange was increased by around 250% in ambient air compared to high purity oxygen at the same pO2. The three experiments performed in this study were used to validate the back-exchange approach and show its utility.

Double perovskite cathodes for proton-conducting ceramic fuel cells: are they triple mixed ionic electronic conductors?

18O and 2H diffusion has been investigated at a temperature of 300 °C in the double perovskite material PrBaCo2O5+δ (PBCO) in flowing air containing 200 mbar of 2H216O. Secondary ion mass spectrometry (SIMS) depth profiling of exchanged ceramics has shown PBCO still retains significant oxygen diffusivity (~1.3 × 10-11 cm2s-1) at this temperature and that the presence of water (2H216O), gives rise to an enhancement of the surface exchange rate over that in pure oxygen by a factor of ~3. The 2H distribution, as inferred from the 2H216O- SIMS signal, shows an apparent depth profile which could be interpreted as 2H diffusion. However, examination of the 3-D distribution of the signal shows it to be nonhomogeneous and probably related to the presence of hydrated layers in the interior walls of pores and is not due to proton diffusion. This suggests that PBCO acts mainly as an oxygen ion mixed conductor when used in PCFC devices, although the presence of a small amount of protonic conductivity cannot be discounted in these materials.

Oxygen exchange and transport in dual phase ceramic composite electrodes.

Composites consisting of a perovskite-based electronic or mixed conductor with a fluorite-structured ionic conductor are often used as electrodes in solid oxide electrochemical energy conversion devices. After sintering the materials, there is often evidence for inter-reaction between the two phases, or inter-diffusion of cations or impurities between the two phases. We studied the (18)O exchange properties of a composite consisting of CGO and LSCF in a 50 : 50 ratio. High resolution ToF-SIMS mapping reveals that the (18)O fraction at the very outer surface of grains of the CGO phase is much higher than expected from D* and k* values for the single-phase parent material. Surface compositional analysis by ToF-SIMS and low energy ion scattering (LEIS) spectroscopy suggests that the surfaces of the CGO grains in the composite do not show the impurities which typically segregate to the surface in single-phase CGO. Thus, the "cleaning" of impurities from the CGO surface by dissolution into the perovskite phase may be one explanation for the apparent enhanced surface exchange for CGO in these composites.

Relating surface chemistry and oxygen surface exchange in LnBaCo2O(5+δ) air electrodes.

The surface and near-surface chemical composition of electroceramic materials often shows significant deviations from that of the bulk. In particular, layered materials, such as cation-ordered LnBaCo2O(5+δ) perovskites (Ln = lanthanide), undergo surface and sub-surface restructuring due to the segregation of the divalent alkaline-earth cation. These processes can take place during synthesis and processing steps (e.g. deposition, sintering or annealing), as well as at temperatures relevant for the operation of these materials as air electrodes in solid oxide fuel cells and electrolysers. Furthermore, the surface segregation in these double perovskites shows fast kinetics, starting at temperatures as low as 400 °C over short periods of time and leading to a decrease in the transition metal surface coverage exposed to the gas phase. In this work, we use a combination of stable isotope tracer labeling and surface-sensitive ion beam techniques to study the oxygen transport properties and their relationship with the surface chemistry in ordered LnBaCo2O(5+δ) perovskites. Time-of-Flight Secondary-Ion Mass Spectrometry (ToF-SIMS) combined with (18)O isotope exchange was used to determine the oxygen tracer diffusion (D*) and surface exchange (k*) coefficients. Furthermore, Low Energy Ion Scattering (LEIS) was used for the analysis of the surface and near surface chemistry as it provides information from the first mono-atomic layer of the materials. In this way, we could relate the compositional modifications (e.g. cation segregation) taking place at the electrochemically-active surface during the exchange at high temperatures and the oxygen transport properties in double perovskite electrode materials to further our understanding of the mechanism of the surface exchange process.

Accurate and precise measurement of oxygen isotopic fractions and diffusion profiles by selective attenuation of secondary ions (SASI).

The accuracy and precision of isotopic analysis in Time-of-Flight secondary ion mass spectrometry (ToF-SIMS) relies on the appropriate reduction of the dead-time and detector saturation effects, especially when analyzing species with high ion yields or present in high concentrations. Conventional approaches to avoid these problems are based on Poisson dead-time correction and/or an overall decrease of the total secondary ion intensity by reducing the target current. This ultimately leads to poor detection limits for the minor isotopes and high uncertainties of the measured isotopic ratios. An alternative strategy consists of the attenuation of those specific secondary ions that saturate the detector, providing an effective extension of the linear dynamic range. In this work, the selective attenuation of secondary ion signals (SASI) approach is applied to the study of oxygen transport properties in electroceramic materials by isotopic labeling with stable (18)O tracer and ToF-SIMS depth profiling. The better analytical performance in terms of accuracy and precision allowed a more reliable determination of the oxygen surface exchange and diffusion coefficients while maintaining good mass resolution and limits of detection for other minor secondary ion species. This improvement is especially relevant to understand the ionic transport mechanisms and properties of solid materials, such as the parallel diffusion pathways (e.g., oxygen diffusion through bulk, grain boundary, or dislocations) in electroceramic materials with relevant applications in energy storage and conversion devices.

Probing the bulk ionic conductivity by thin film hetero-epitaxial engineering.

Highly textured thin films with small grain boundary regions can be used as model systems to directly measure the bulk conductivity of oxygen ion conducting oxides. Ionic conducting thin films and epitaxial heterostructures are also widely used to probe the effect of strain on the oxygen ion migration in oxide materials. For the purpose of these investigations a good lattice matching between the film and the substrate is required to promote the ordered film growth. Moreover, the substrate should be a good electrical insulator at high temperature to allow a reliable electrical characterization of the deposited film. Here we report the fabrication of an epitaxial heterostructure made with a double buffer layer of BaZrO3 and SrTiO3 grown on MgO substrates that fulfills both requirements. Based on such template platform, highly ordered (001) epitaxially oriented thin films of 15% Sm-doped CeO2 and 8 mol% Y2O3 stabilized ZrO2 are grown. Bulk conductivities as well as activation energies are measured for both materials, confirming the success of the approach. The reported insulating template platform promises potential application also for the electrical characterization of other novel electrolyte materials that still need a thorough understanding of their ionic conductivity.

Controlling the surface termination of NdGaO3 (110): the role of the gas atmosphere.

In this work the effect of gas atmosphere on the surface termination reconstruction of single crystal NdGaO3 (110) (NGO) during thermal annealing was analyzed. Using Low Energy Ion Scattering (LEIS) it has been possible to study the chemical composition of the first atomic layer of treated NGO single crystal samples. NGO has been analyzed both as-received and after a specific thermal treatment at 1000 °C under different gas fluxes (argon, nitrogen, static air, synthetic air, nitrogen plus 5% hydrogen and wet synthetic air respectively). Thermal annealing of perovskite single crystals, as already reported in the literature, is used to obtain a fully A-cation surface termination. Nevertheless the effect of the gas-atmosphere on this process has not been previously reported. By the use of sequential low energy Ar(+) sputtering combined with the primary ion LEIS analysis, the reconstruction of the outermost atomic layers has allowed the clarification of the mechanism of NGO neodymium surface enrichment. It is proposed that the gallium at the surface is submitted to a reduction/evaporation mechanism caused by low oxygen partial pressure and/or high water pressure in the vector gas. Below the first surface atomic layers of an as-received NGO single-crystal a gallium-rich phase has also been observed.

A family of oxide ion conductors based on the ferroelectric perovskite Na0.5Bi0.5TiO3.

Oxide ion conductors find important technical applications in electrochemical devices such as solid-oxide fuel cells (SOFCs), oxygen separation membranes and sensors. Na0.5Bi0.5TiO3 (NBT) is a well-known lead-free piezoelectric material; however, it is often reported to possess high leakage conductivity that is problematic for its piezo- and ferroelectric applications. Here we report this high leakage to be oxide ion conduction due to Bi-deficiency and oxygen vacancies induced during materials processing. Mg-doping on the Ti-site increases the ionic conductivity to ~0.01 S cm(-1) at 600 °C, improves the electrolyte stability in reducing atmospheres and lowers the sintering temperature. This study not only demonstrates how to adjust the nominal NBT composition for dielectric-based applications, but also, more importantly, gives NBT-based materials an unexpected role as a completely new family of oxide ion conductors with potential applications in intermediate-temperature SOFCs and opens up a new direction to design oxide ion conductors in perovskite oxides.

Calculation of arrangement of oxygen ions and vacancies in double perovskite GdBaCo2O(5+δ) by first-principles DFT with Monte Carlo simulations.

The configurations of oxygen ions and vacancies at various oxygen stoichiometries and temperatures in double perovskite oxides (GdBaCo2O(5+δ), 0 ≤ δ ≤ 1) have been determined by density functional theory (DFT) combined with Monte Carlo (MC) simulations. The MC simulations confirmed the existence of a superstructure at δ = 0.5, showing alternating linear ordering of oxygen ions and vacancies along the b-axis in the GdO layer. This structure is identical to that reported experimentally. Increasing the temperature up to 1200 K induces a phase transition manifested in the breaking of the oxygen/vacancy arrangement at around δ = 0.5. In the high-temperature phase, vacancies are distributed in the GdO and CoO2 layers, whereas there are no vacancies in the BaO layer. In addition, the characteristic linear arrangement is partly preserved even in the disordered high-temperature phase. Consequently, oxygen ions can migrate between the GdO and CoO2 layers, as reported in previous classical molecular dynamics simulation studies.

Testing the Chemical/Structural Stability of Proton Conducting Perovskite Ceramic Membranes by in Situ/ex Situ Autoclave Raman Microscopy.

Ceramics, which exhibit high proton conductivity at moderate temperatures, are studied as electrolyte membranes or electrode components of fuel cells, electrolysers or CO2 converters. In severe operating conditions (high gas pressure/high temperature), the chemical activity towards potentially reactive atmospheres (water, CO2, etc.) is enhanced. This can lead to mechanical, chemical, and structural instability of the membranes and premature efficiency loss. Since the lifetime duration of a device determines its economical interest, stability/aging tests are essential. Consequently, we have developed autoclaves equipped with a sapphire window, allowing in situ Raman study in the 25-620 °C temperature region under 1-50 bar of water vapor/gas pressure, both with and without the application of an electric field. Taking examples of four widely investigated perovskites (BaZr0.9Yb0.1O3-δ, SrZr0.9Yb0.1O3-δ, BaZr0.25In0.75O3-δ, BaCe0.5Zr0.3Y0.16Zn0.04O3-δ), we demonstrate the high potential of our unique set-up to discriminate between good/stable and instable electrolytes as well as the ability to detect and monitor in situ: (i) the sample surface reaction with surrounding atmospheres and the formation of crystalline or amorphous secondary phases (carbonates, hydroxides, hydrates, etc.); and (ii) the structural modifications as a function of operating conditions. The results of these studies allow us to compare quantitatively the chemical stability versus water (corrosion rate from ~150 µm/day to less than 0.25 µm/day under 200-500 °C/15-80 bar PH2O) and to go further in comprehension of the aging mechanism of the membrane.