Scalable Superior Chemical Sensing Performance of Stretchable Ionotronic Skin via a π-Hole Receptor Effect.

Skin-attachable gas sensors provide a next-generation wearable platform for real-time protection of human health by monitoring environmental and physiological chemicals. However, the creation of skin-like wearable gas sensors, possessing high sensitivity, selectivity, stability, and scalability (4S) simultaneously, has been a big challenge. Here, an ionotronic gas-sensing sticker (IGS) is demonstrated, implemented with free-standing polymer electrolyte (ionic thermoplastic polyurethane, i-TPU) as a sensing channel and inkjet-printed stretchable carbon nanotube electrodes, which enables the IGS to exhibit high sensitivity, selectivity, stability (against mechanical stress, humidity, and temperature), and scalable fabrication, simultaneously. The IGS demonstrates reliable sensing capability against nitrogen dioxide molecules under not only harsh mechanical stress (cyclic bending with the radius of curvature of 1 mm and cyclic straining at 50%), but also environmental conditions (thermal aging from -45 to 125 °C for 1000 cycles and humidity aging for 24 h at 85% relative humidity). Further, through systematic experiments and theoretical calculations, a π-hole receptor mechanism is proposed, which can effectively elucidate the origin of the high sensitivity (up to parts per billion level) and selectivity of the ionotronic sensing system. Consequently, this work provides a guideline for the design of ionotronic materials for the achievement of high-performance and skin-attachable gas-sensor platforms.

Inkjet-Printed Carbon Nanotubes for Fabricating a Spoof Fingerprint on Paper.

A spoof fingerprint was fabricated on paper and applied for a spoofing attack to unlock a smartphone on which a capacitive array of sensors had been embedded with a fingerprint recognition algorithm. Using an inkjet printer with an ink made of carbon nanotubes (CNTs), we printed a spoof fingerprint having an electrical and geometric pattern of ridges and furrows comparable to that of the real fingerprint. With this printed spoof fingerprint, we were able to unlock a smartphone successfully; this was due to the good quality of the printed CNT material, which provided electrical conductivities and structural patterns similar to those of the real fingerprint. This result confirms that inkjet-printing CNTs to fabricate a spoof fingerprint on paper is an easy, simple spoofing route from the real fingerprint and suggests a new method for outputting the physical ridges and furrows on a two-dimensional plane.

Affordable Fabrication of Conductive Electrodes and Dielectric Films for a Paper-based Digital Microfluidic Chip.

In order to fabricate a digital microfluidic (DMF) chip, which requires a patterned array of electrodes coated with a dielectric film, we explored two simple methods: Ballpoint pen printing to generate the electrodes, and wrapping of a dielectric plastic film to coat the electrodes. For precise and programmable printing of the patterned electrodes, we used a digital plotter with a ballpoint pen filled with a silver nanoparticle (AgNP) ink. Instead of using conventional material deposition methods, such as chemical vapor deposition, printing, and spin coating, for fabricating the thin dielectric layer, we used a simple method in which we prepared a thin dielectric layer using pre-made linear, low-density polyethylene (LLDPE) plastic (17-µm thick) by simple wrapping. We then sealed it tightly with thin silicone oil layers so that it could be used as a DMF chip. Such a treated dielectric layer showed good electrowetting performance for a sessile drop without contact angle hysteresis under an applied voltage of less than 170 V. By using this straightforward fabrication method, we quickly and affordably fabricated a paper-based DMF chip and demonstrated the digital electrofluidic actuation and manipulation of drops.

Effects of Silicone Oil on Electrowetting to Actuate a Digital Microfluidic Drop on Paper.

The effects of an immiscible, lubricating polydimethylsiloxane fluid, referred to as silicone oil, on the static deformation and on the dynamic motion of a water drop on paper induced by electrowetting were investigated. The deformation of a drop on a hydrophobic film of amorphous fluoropolymers top-coated with less hydrophobic silicone oil was much more predictable, reversible and reproducible than on the uncoated surface. In the dynamic tribological experiment for a sliding drop along an inclined surface, a significant decrease in the friction coefficient, with an unexpected dependency of the contact area, was observed. Based on the curve fitting analysis, the shear stress and the net friction force were estimated quantitatively. Because of the tribological effect and the reduced shear friction force of the oil film, the static and the dynamic electrowetting states of the water drop were enhanced.