Ex vivo comparison of lateral plate repairs of experimental oblique ilial fractures in cats.

OBJECTIVE: To determine the biomechanical behavior of different plate systems used for oblique ilial fracture fixation in cats. STUDY DESIGN: Ex vivo biomechanical study. SAMPLE POPULATION: Fifty fresh-frozen feline hemipelvises. METHODS: Standardized simple oblique ilial fractures were created and fixed via lateral plating, using different implant systems (10 fractures in each group) The systems were: (1) the Advanced Locking Plate System (ALPS-5); (2) the Advanced Locking Plate System (ALPS-6.5); (3) the Locking Compression Plate 2.0 (LCP); (4) the FIXIN 1.9-2.5 Series (FIXIN), and (5) the Dynamic Compression Plate 2.0 (DCP). Stepwise sinusoidal cyclic loading was applied until failure (10-mm displacement). The groups were compared with regard to construct stiffness and the number of cycles withstood before 1-, 2-, 5-, and 10-mm displacement. RESULTS: Bending stiffness was lower in ALPS-5 than in other specimens (P < .05). The ALPS-6.5 specimens withstood more cycles (P < .05) before 2-, 5-, and 10-mm displacement than the ALPS-5 and DCP specimens . The LCP and FIXIN specimens endured more cycles than DCP specimens before displaying 5- and 10-mm displacement (P < .05). The ALPS-6.5, FIXIN, and LCP specimens endured higher loads before failure than the DCP specimens (P < .05). Screw loosening occurred in all nonlocking specimens, and bone slicing occurred in all locking specimens. CONCLUSION: The DCP and ALPS-5 constructs are less resistant to cyclic loading. Failure in nonlocking specimens involved screw loosening. It involved bone slicing in locking specimens. CLINICAL SIGNIFICANCE: Both the plate size and the plate-screw interface are key to lateral plating success in cases of feline ilial fractures. The use of locking plates reduces the risk of the screw loosening in such cases.

Ex vivo study of the intradiskal pressure in the C6-7 intervertebral disk after experimental destabilization and distraction-fusion of the C5-C6 vertebrae in canine cadaveric specimens.

OBJECTIVE: To evaluate intradiskal pressure (IDP) in the C6-7 intervertebral disk (IVD) after destabilization and distraction-fusion of the C5-C6 vertebrae. SAMPLE: 7 cadaveric C4-T1 vertebral specimens with no evidence of IVD disease from large-breed dogs. PROCEDURES: Specimens were mounted in a custom-made 6 degrees of freedom spinal loading simulator so the C5-C6 and C6-C7 segments remained mobile. One specimen remained untreated and was used to assess the repeatability of the IDP measurement protocol. Six specimens underwent 3 sequential configurations (untreated, partial diskectomy of the C5-6 IVD, and distraction-fusion of the C5-C6 vertebrae). Each construct was biomechanically tested under neutral, flexion, extension, and right-lateral bending loads. The IDP was measured with a pressure transducer inserted into the C6-7 IVD and compared between the nucleus pulposus and annulus fibrosus and across all 3 constructs and 4 loads. RESULTS: Compared with untreated constructs, partial diskectomy and distraction-fusion of C5-C6 decreased the mean ± SD IDP in the C6-7 IVD by 1.3 ± 1.3% and 0.8 ± 1.3%, respectively. During motion, the IDP remained fairly constant in the annulus fibrosus and increased by 3.8 ± 3.0% in the nucleus pulposus. The increase in IDP within the nucleus pulposus was numerically greatest during flexion but did not differ significantly among loading conditions. CONCLUSIONS AND CLINICAL RELEVANCE: Distraction-fusion of C5-C6 did not significantly alter the IDP of healthy C6-7 IVDs. Effects of vertebral distraction-fusion on the IDP of adjacent IVDs with degenerative changes, such as those in dogs with caudal cervical spondylomyelopathy, warrant investigation.

Ex vivo Evaluation of the Dynamic Morphometry of the Caudal Cervical Intervertebral Disc Spaces of Small Dogs and Cats.

The objective of this study was to provide a morphometric description of the caudal cervical intervertebral disc (IVD) spaces of small-breed dogs and cats. Specimens consisting of C4 through C7 from five small-breed dogs and six cats were positioned in neutral, flexion, extension, and lateral bending positions; and CT images were acquired. Height and width of the cranial and caudal vertebral endplates (VEPs), angle between the VEPs (IVD wedge angle), and craniocaudal distance (IVD width) between VEPs for the four loading positions were measured and compared for three segments (C4-C5, C5-C6, and C6-C7). VEP size normalized to body weight from medium-sized dogs was retrieved from a previous study and compared with data from small dogs and cats. A linear mixed model was used to compare outcome measures. Significance was set to p < 0.05. VEP size normalized to body weight was the largest in small dogs compared with cats (p = 0.0422) and medium-sized dogs (p = 0.0064). Cats and medium-sized dogs were similar (p = 0.2763) in this regard. Flexion and extension induced a reduction of IVD width in the ventral portion of the IVD and the area of the nucleus. The dorsal part of the IVD remained unchanged throughout loading conditions. Unique morphometric characteristics of the caudal cervical IVD space of small dogs and cats were detected that are different from those described in sizes of dogs (medium-sized) typically affected by caudal cervical spondylomyelopathy (CSM). These findings may help to understand the different pathomechanisms in cervical spinal disease between small- and medium-sized dogs, including caudal CSM.

Biomechanical comparison of ex vivo lumbar vertebral fracture luxations stabilized with tension band or polymethylmethacrylate in cats.

OBJECTIVE: To evaluate spinal stabilization with tension band stabilization (TS) in cats compared to screw and polymethylmethacrylate fixation (SP). STUDY DESIGN: Ex vivo study. SAMPLE POPULATION: Sixteen feline thoracolumbar spinal specimens. METHODS: The intact specimens were mounted in a six-degree-of-freedom biaxial testing machine for nondestructive testing to obtain the neutral zones (NZ) and range of motion (ROM) in flexion and extension. Thereafter, nondestructive testing was consecutively performed after destabilization by disc fenestration and partial L1 corpectomy and after treatment with either TS or SP. Load to failure was compared after surgical treatment in flexion. Significance was assessed by Student's t test or Wilcoxon signed-rank test. RESULTS: Range of motion was 26.4° ± 2.2° in TS constructs and 13.4° ± 2.1° in SP constructs (P = .0005). When flexion and extension were analyzed separately, no difference was found for ROM in flexion (SP, 7.0° ± 3.7°; TS, 8.3° ± 2.1°; P = .38). In extension, the mean displacement was 6.4° ± 2.7° and 18.1° ± 5.1° in SP and TS constructs, respectively (P = .0001). Neutral zone was 2.9° ± 0.6° and 7.5° ± 0.8° for the SP and TS groups, respectively (P = .0003). Screw and polymethylmethacrylate fixation constructs were two times stiffer (P = .045). CONCLUSION: Tension band stabilization provided stability comparable to SP in flexion. In extension, ROM of SP constructs was half that of TS constructs. The mode of failure of TS was related to the limited dorsal bone stock of feline lumbar vertebrae. CLINICAL SIGNIFICANCE: Surgeons should be aware of the limited stability in extension provided by TS when it is used to stabilize thoracolumbar spinal injuries. Our results provide evidence to justify additional studies to clarify the type of fractures amenable to TS.

Influence of a customized three-dimensionally printed drill guide on the accuracy of pedicle screw placement in lumbosacral vertebrae: An ex vivo study.

OBJECTIVE: To compare the accuracy of pedicle screw insertion (PSI) into canine lumbosacral vertebrae with custom-made three-dimensionally (3D)-printed drill guides or freehand insertion. STUDY DESIGN: Ex vivo study. SAMPLE POPULATION: Nineteen canine lumbosacral specimens. METHODS: Drill guides for PSI were designed on the basis of safe screw insertion trajectories by using preoperative computed tomography (CT) and produced by 3D printing of templates. Right and left sides of the specimens were randomly allocated to two groups; 4-mm pedicle screws were inserted in L5-L6 and L7-S1 spinal segments either freehand (control group) or with custom-made drill guides (guide group). Sixty-six screws were inserted with each method. Insertion angles (α, ß), bone stock, and vertebral canal breach were assessed according to postoperative CT. χ2 Tests were used to compare vertebral canal breach between groups and vertebrae. RESULTS: Breaches in the vertebral canal were less common (P < .001) when screws were placed with a guide in the guide group (9/66, 14%) than without a guide (30/66, 45%). The rate of vertebral canal breach differed at L5 (P = .021) but not at L6 (P = .05), L7 (P = .075) or S1 (P = .658). The angle of insertion (α) did not differ between specimens with and without breaches (guide, P = .068; control, P = .394). CONCLUSION: The use of a customized 3D-printed guide generally improved the accuracy of PSI in canine lumbosacral vertebrae, although statistical significance was reached only at L5. CLINICAL SIGNIFICANCE: The use of customized drill guides may be considered as an alternative to freehand PSI in the lumbosacral area, especially for L5-L6 vertebrae.

Recommendations for rehabilitation after surgical treatment of cranial cruciate ligament disease in dogs: A 2017 survey of veterinary practitioners.

OBJECTIVE: To report current recommendations made by veterinarians for rehabilitation after surgical treatment of cranial cruciate ligament (CrCL) disease. STUDY DESIGN: Anonymized electronic survey. SAMPLE POPULATION: Veterinarians performing CrCL stabilization. METHODS: An electronic survey was created to collect information on general attitudes toward postoperative rehabilitation and recommendations regarding therapeutic modalities and bandaging. Quantitative data are reported by descriptive statistical analysis, percentage of responses, or mean (±SD). The recommendations for postoperative bandaging beyond 24 hours and for postoperative rehabilitation after extracapsular stabilization compared with after tibial osteotomy were tested by using Cochran-Mantel-Haenszel tests, with P < .05 considered statistically significant. RESULTS: The data analysis included 376 responses (13% response rate). Most (71%) respondents consistently recommended postoperative rehabilitation. Rehabilitation was more than twofold more likely to be recommended after extracapsular stabilization than after osteotomies (P = .0142). Most respondents did not recommend bandaging beyond 24 hours postoperatively (P = .00012). CONCLUSION: Most respondents recommended either formal or informal postoperative rehabilitation therapy. CLINICAL SIGNIFICANCE: If the survey respondents are representative of veterinarians performing CrCL surgery, the current attitude is supportive of postsurgical rehabilitation. Most respondents would welcome evidence-based guidelines for rehabilitation protocols.

Biomechanical comparison of knotted and knotless stabilization techniques of the tarsal medial collateral ligament in cats: A cadaveric study.

OBJECTIVE: To compare mechanical properties of intact feline medial collateral ligaments and three techniques for treatment of feline medial tarsal instability. STUDY DESIGN: Controlled laboratory study. SAMPLE POPULATION: Forty-eight normal, adult feline tarsi. METHODS: Three repairs were tested: a bone tunnel with polypropylene (PP) suture, a bone tunnel with polyethylene (PE) cord, and a knotless anchor technique with PE cord. A cyclic (6-N preload; 5-N amplitude; 2-Hz frequency) tensile test (600 cycles) was performed on feline tarsi with either the long or the short medial tarsal ligament intact, with each reconstruction technique followed by a single-cycle load-to-failure test (0.5 mm/s) with a failure point at 2 mm of displacement. Total elongation, peak-to-peak elongation, stiffness, and maximum load to failure point were compared with the intact condition. RESULTS: No differences in stiffness, total elongation, or peak-to-peak elongation were found between specimens repaired with the knotless technique and intact controls (P > .04), whereas tarsi repaired with the tunnel technique and PP were weaker (P < .008). Total and conditioning elongation were greater after tunnel reconstruction with PP than after knotless reconstruction (P = .005). Mean load to 2 mm of displacement tended (P = .03) to be higher after knotless than after knotted PP repairs and did not differ (P = .47) between tarsi repaired with the tunnel or anchor repairs with PE. CONCLUSION: The mechanical properties of intact tarsi were superior to those of tarsi repaired with tunnel techniques and PP but were similar to those of tarsi repaired with knotless techniques with PE. CLINICAL SIGNIFICANCE: Feline tarsal stabilization with the knotless technique for tarsal medial collateral ligament insufficiency may reduce the requirement for or duration of postoperative coaptation.

Safety and Accuracy of Minimally Invasive Long Bone Fracture Repair Using a 2.5-mm Interlocking Nail: A Cadaveric Feline Study.

OBJECTIVES: The Targon Vet System (TVS) is a 2.5-mm interlocking nail that can be applied minimally invasively. The purpose of this study was to test if the TVS could be safely applied percutaneously to different feline long bones without fluoroscopic guidance. METHODS: A gap fracture was created in 96 feline humeri, femora and tibiae (n = 32/group). Paired bones were randomly assigned to two treatment groups: (1) TVS inserted percutaneously with fluoroscopy and (2) TVS inserted percutaneously without fluoroscopy. Intraoperative evaluation (complications, procedure time, attempts), radiographs (pre-/postoperative alignment, length) and anatomical dissection (neurovascular injury, rotational alignment) were compared between treatment groups. RESULTS: The use of fluoroscopy did not lead to significant differences in any of the outcome measures. Intraoperative complications predominantly occurred in the distal humerus (12/32) and the proximal femur (7/32). In total, 20/96 complications occurred with no complications for the tibia. Neurovascular structures were only damaged at the medial side of the distal humerus (10/32). CLINICAL SIGNIFICANCE: We conclude that the TVS can be safely applied percutaneously to the tibia and with limitations to the femur in normal cadaveric cats without fluoroscopy. Despite the limitations of a cadaveric study, the high number of complications is leading us to consider the humerus not safe for the TVS. A learning curve has to be expected and technical recommendations should be respected to decrease complications.

Ex vivo computed tomography evaluation of loading position on morphometry of the caudal cervical intervertebral disk spaces of dogs.

OBJECTIVE To provide an objective, quantitative morphometric description of the caudal cervical intervertebral disk (IVD) spaces of dogs. SAMPLE Vertebral specimens consisting of C4 through C7 from 5 medium-sized dogs. PROCEDURES CT images were obtained with the specimens positioned in neutral, flexion, extension, and lateral bending positions. Size and shape of the cranial and caudal end plates, angle between the end plates (IVD wedge angle), and craniocaudal distance (IVD width) between end plates for the 4 loading positions were measured and compared for the 3 segments (C4-5, C5-6, and C6-7). RESULTS End plate size and shape, IVD wedge angle, and IVD width were not significantly different among the 3 segments. Caudal cervical end plates were consistently larger than cranial cervical end plates. The IVD wedge angle ranged from -4.8° to 15.2°. Flexion induced a reduction in IVD width in the ventral portion of the IVD, whereas extension induced a decrease in width in the dorsal portion of the IVD. Central IVD width remained unchanged among the loading positions. CONCLUSIONS AND CLINICAL RELEVANCE Unique morphometric and dynamic characteristics of the caudal cervical IVD space of dogs were detected. These findings may help investigators when designing IVD prostheses for dogs with cervical spondylomyelopathy.

Biomechanical properties of plate constructs for feline ilial fracture gap stabilization.

OBJECTIVE: To determine the biomechanical properties of plating techniques for comminuted feline ilial fractures. STUDY DESIGN: Ex vivo study on 40 paired feline hemipelves. SAMPLE POPULATION: Forty paired fresh-frozen hemipelves that had been collected from 20 cats aged 2-6 years and weighing 4.0-5.5 kg. METHODS: A transverse 3-mm gap was created in each ilium. Hemipelves were fixed with one of the following methods (n = 10 per group): (1) a dorsal plate and nonlocking screws, (2) a lateral plate and nonlocking screws, (3) a lateral plate and locking screws, or (4) a lateral and dorsal locking compression plate using nonlocking screws. Each specimen was subjected to incremental, sinusoidal cyclic loading until failure, defined as 10-mm displacement. The initial stiffness and number of cycles required to reach 1-, 2-, 5-, and 10-mm axial displacement were statistically analyzed. RESULTS: The initial stiffness and number of cycles to failure were higher in specimens fixed with double nonlocking plates than in all other fixations (P < .05) except specimens fixed with lateral locking plate at 10-mm displacement (P = .44). Locking implants withstood more cycles to 5- (P < .05) and 10-mm (P < .05) displacement compared with other single-plate nonlocking groups. Screw loosening occurred only in the 3 nonlocking fixations. CONCLUSION: Double plating improved stiffness and resistance to failure of comminuted feline ilial fracture constructs compared with all other fixations. Single locking plates produced superior constructs compared with single nonlocking constructs. CLINICAL SIGNIFICANCE: Locking implants are recommended to repair comminuted feline ilial fractures for their extended fatigue life and resistance to screw loosening. Orthogonal plating offers a strong nonlocking alternative.

Screw Loosening and Pelvic Canal Narrowing After Lateral Plating of Feline Ilial Fractures With Locking and Nonlocking Plates.

OBJECTIVE: To compare the frequency of complications, including screw loosening and pelvic canal narrowing, associated with dynamic compression plating, locking plating, and double locking plating of ilial fractures in cats. STUDY DESIGN: Historical cohort study. METHODS: The radiographs and medical records of cats with pelvic fractures that were presented between 2004 and 2013 were reviewed. The cases were categorized based on the plate type and number as dynamic compression plate (DCP), single locking plate (LPS) and double locking plates (dLPS). The frequency of screw loosening was compared across categories using a Fisher's exact test. The change in pelvic alignment, described by the change in sacral index (postoperative sacral index-followup sacral index), was compared across plate categories using ANOVA. RESULTS: The frequency of screw loosening for DCP (5/10) was significantly higher than LPS (1/13) and dLPS (0/11) (P = .05, P = .012, respectively). There was no significant difference in the SI change across plate categories. The mean change in sacral index for DCP was -0.11 (95%CI -0.25 to 0.03), for LPS was 0.0007 (95%CI -0.07 to 0.08), and for dLPS was -0.01 (95%CI -0.04 to 0.02). None of the cats showed constipation postoperatively. CONCLUSION: Screw loosening occurred less often but the change in pelvic canal alignment was not significantly different in ilial fractures repaired with LPS or dLPS compared to ilial fractures repaired with DCP. Locking plating of ilial fractures in cats may offer advantages compared to nonlocking plating.

Biomechanical comparison after in vitro laminar vertebral stabilization and vertebral body plating of the first and second lumbar vertebrae in specimens obtained from canine cadavers.

OBJECTIVE: To compare biomechanical characteristics of vertebral segments after vertebral body plating or laminar stabilization following complete incision of the annulus fibrosus. SAMPLE: Vertebral segments from T13 through L3 obtained from 18 canine cadavers. PROCEDURES: A 4-point bending moment was applied in flexion and extension to the intact vertebral segments to determine a baseline range of motion (ROM) and neutral zone (NZ). Vertebral columns were then destabilized by creating a defect in the intervertebral disk via complete incision of the ventral aspect of the annulus fibrosus. The bending moment was applied again after stabilization was accomplished via vertebral body plating or with laminar stabilization (n = 9 vertebral segments/stabilization technique). The ROM and NZ were compared with their baseline values and among treatment groups. Finally, load-to-failure testing was performed in flexion. RESULTS: Mean relative ROM and NZ for segments treated with laminar stabilization were significantly lower than those for segments treated with vertebral plates. CONCLUSIONS AND CLINICAL RELEVANCE: Analysis of in vitro results suggested that laminar stabilization of vertebral segments provided greater stiffness than did vertebral body plating.

Angle of insertion and confirmation of angles measured after in vitro implantation during laminar vertebral stabilization in vertebral columns obtained from canine cadavers.

OBJECTIVE: To determine angles of insertion for laminar vertebral fixation of L1 and L2 by use of a locking plate in dogs and to confirm screw placement by use of computed tomography (CT). SAMPLE: Vertebral specimens harvested from 8 canine cadavers. PROCEDURES: The point of insertion and minimum and maximum insertion angles for laminar and facet screws for laminar vertebral stabilization were determined by use of CT. A precontoured locking plate was then placed by use of 1 locking screw in the lamina of each lumbar vertebra and 1 nonlocking screw in the facet joint. The position and angle of the screws were examined by use of CT, and penetration into the vertebral canal was recorded. RESULTS: Mean ± SD insertion angles for L1 and L2 were 18 ± 4° and 21 ± 5° toward the vertebral canal and 11 ± 4.4° and 10 ± 3° in a dorsal direction, respectively. Insertion angles for the facet joint were between 24 ± 4° ventrally and 12 ± 2° dorsally. Insertion of the screw did not penetrate the vertebral canal for 23 of 24 (96%) screws. For 23 of 24 inserted screws, the previously determined angle was maintained and purchase of bone and cortices was satisfactory. CONCLUSIONS AND CLINICAL RELEVANCE: Placement of laminar and facet screws in canine vertebrae was possible and can be performed safely if angles of insertion determined pre-operatively via CT are maintained.

Successful treatment of small intestinal volvulus in two cats.

BACKGROUND: Mesenteric volvulus describes a torsion of the small intestine around the mesenteric root, which can be partial or complete. In dogs, it is an uncommon condition, with German shepherd dogs showing a predisposition. Chronic mesenteric volvulus has also been described. In cats, previous reports have documented two cases of small intestinal volvulus, both diagnosed at necropsy, and a further case of volvulus of the colon in a patient that died after surgery. CLINICAL SIGNIFICANCE: This report describes two cats with mesenteric volvulus that were successfully treated. To the authors' knowledge, no reports of antemortem diagnosis or treatment of small intestinal volvulus in cats have previously been published. On the basis of the cases presented, it appears that the diagnosis of intestinal volvulus may be more difficult in cats than in dogs, but that the prognosis may not be as poor. Therefore, it is suggested that owners be encouraged to pursue surgery.