Gas chromatography mass spectrometer determination of dimethylamine impurity in N,N-dimethylformamide solvent by derivatization of N,N-dimethylbenzamide with benzoyl chloride agent.

This study describes the development of a reliable and linear analytical method for precisely determining dimethylamine impurity in N,N-dimethylformamide solvent utilizing a benzoyl chloride derivatization reagent and a gas chromatography mass spectrometer. Benzoyl chloride was used to derivatize dimethylamine. At normal temperature, benzoyl chloride combined with dimethylamine, producing N,N-dimethylbenzamide. This method separated N,N-dimethylbenzamide using Rtx-5 amine (30 m × 0.32 mm × 1.50 µm) as the stationary phase, helium as the carrier gas, argon as the collision gas, and methanol as the diluent. The column flow rate was 2 mL/min. The retention time of N,N-dimethylbenzamide was determined to be 8.5 min. Precision, linearity, and accuracy were tested using ICH Q2 (R2) and USP<1225> guidelines. The percentage coefficient of variation (CV) for N,N-dimethylbenzamide in the system suitability parameter was 1.1%. The correlation coefficient of N,N-dimethylbenzamide was found to be >0.99. In the method precision parameter, the % CV for N,N-dimethylbenzamide was found to be 1.9%, whereas the % CV for N,N-dimethylbenzamide was 1.2% in intermediate precision. The percentage recovery of N,N-dimethylbenzamide was determined to be between 80% and 98%.

Quality by Design Tool Assessed Ultraperformance Liquid Chromatography Method for the Analysis of Remogliflozin and Teneligliptin in Oral Dosage Form.

The UPLC methodology was used to establish a method for determining the qualitative and quantitative content of teneligliptin and remogliflozin tablets in oral solid dose form, as no simultaneous method was available. The developed liquid chromatography method consists of an X-Bridge C18 100 mm × 3.5 mm, 2.1 mm column with an economical 0.2 mL/min flow rate. A wavelength of 248 nm was used for detection, and the temperature of the column compartment was 30 °C. The method was evaluated using a static tool quality by design after it was validated as per the regulations. The data from validation result in linearity for both analytes with a correlation coefficient of more than 0.999. The accuracy data were found from a minimum of 98.1 to a maximum of 100.9. All of the validation results met the acceptance criteria. The stability of the analytical solutions proved for 24 h at bench and refrigerator temperatures. Studies of force degradation proved the stability indicating the nature of the method. A factorial design was used to evaluate the method performance.

Analytical determination of ethylenediamine impurity in tripelennamine hydrochloride by gas chromatography-mass spectrometry using phthalaldehyde as the derivatizing agent.

In the pharmaceutical industry, effective risk management and control strategies for potential genotoxic impurities are of paramount importance. The current study utilized GC-MS to evaluate a precise, linear, and accurate analytical method for quantifying ethylenediamine present in tripelennamine hydrochloride using phthalaldehyde as a derivatizing agent. When phthalaldehyde is sonicated for 10 min at room temperature, it reacts with ethylenediamine to form (1z,5z)-3,4-dihydrobenzo[f][1,4]diazocine. This approach minimizes matrix interference issues and resolves sample preparation difficulties encountered during ethylenediamine identification in GC-MS. In this method, helium serves as the carrier gas, while methanol acts as the diluent. The stationary phase consists of a DB-5MS column (30 m × 0.25 mm × 0.25 µm) with a flow rate of 1.5 mL/min. The retention time of (1z,5z)-3,4-dihydrobenzo[f][1,4]diazocine was determined to be 6.215 min. The method validation demonstrated limits of detection and quantification for (1z,5z)-3,4-dihydrobenzo[f][1,4]diazocine at 0.4 and 1.0 ppm, respectively, with a linearity range spanning from 1 to 30 ppm concentration with respect to the specification level. System suitability, precision, linearity, and accuracy of the current method were assessed in accordance with guidelines, yielding results deemed suitable for the intended use.

Quantification of Drospirenone- and Ethinyl Estradiol-Related Impurities in a Combined Pharmaceutical Dosage Form by a Chromatography Method With a QbD Robustness Study.

BACKGROUND: The estimation of drugs containing drospirenone (DRSP) and ethinyl estradiol (EE), and their related impurities, in low-dose oral contraceptive drug products is an extremely challenging target. The proposed research sought to develop and validate a stability-indicating method for quantifying drug substances and their related impurities in tablet formulation. OBJECTIVE: To develop and validate a simple, specific, accurate, precise, and stability-indicating reverse-phase (RP)-HPLC method for quantification of DRSP, EE, and their impurities in accordance with International Conference on Harmonisation (ICH) guidelines. METHOD: The separation was achieved using an Agilent Zorbax SB C18 column (4.6 mm × 250 mm, 5 µm) with a detection wavelength of 215 nm and mobile phases A (100% acetonitrile) and B (acetonitrile-water, 1 + 3, v/v) at a flow rate of 1.3 mL/min and a column temperature of 40°C. RESULTS: The recovery study of each impurity was conducted in the range of 24 to 72 µg/mL for DRSP-related impurities and 0.2 to 0.6 µg/mL for EE-related impurities with respect to the specification limit. A linearity study was conducted over a range of 1.5 to 90 µg/mL for DRSP and DRSP-related impurities, and 0.125 to 0.75 µg/mL for EE-related impurities. A Quality by Design (QbD) study demonstrated the method's robustness. CONCLUSIONS: As per current guidelines, a stability-indicating method has been developed for the determination of impurities in DRSP/EE film-coated tablets. A QbD-based robustness test was performed and the method was found to be robust. HIGHLIGHTS: An accurate, precise, stability-indicating, gradient RP-HPLC method has been developed and validated to determine DRSP, EE, and nine related impurities in tablet formulation. A QbD technique was used to establish a robustness study.

A quality-by-design evaluated liquid chromatography method development and validation for the separation and quantification of nitroxoline and its impurities.

A novel, isocratic, sensitive, stability-indicating high-performance liquid chromatography method was developed for the separation and quantification of related substances in nitroxoline (NTL). The chromatographic separation has been achieved on Inertsil ODS-3 V, (250 × 4.6 mm, 5 µm) at 240 nm using ethylenediamine tetraacetic acid buffer and methanol in the ratio of 60:40 v/v as mobile phase. The performance of the method has been checked as per the International Conference on Harmonization guidelines for specificity, linearity, accuracy, precision, and robustness. Regression analysis showed a correlation coefficient value greater than 0.99 for NTL and its three impurities. The detection limit of impurities was in the range of 0.01% (0.05 µg/mL)-0.22% (1.1 µg/mL) indicating the sensitivity of the newly developed method. The accuracy of the method was established based on the recovery obtained between 94.7% and 104.1% for all the impurities. The percentage relative standard deviation obtained for the repeatability was less than 4.0% at the specification level for all impurities. Forced degradation was performed to establish the stability-indicating nature of the method and to know about the degradation products, the quality of a drug substance changes with time under the influence of stress conditions. Thus, the proposed method was validated and found to be specific, sensitive, linear, accurate, precise, reproducible, and beneficial for routine usage.

Quality by design tool-evaluated stability-indicating ultra-performance liquid chromatography method for the determination of drugs (ritonavir and darunavir) used to treat the human immunodeficiency virus/acquired immunodeficiency syndrome.

Ritonavir and darunavir were examined using a ultra-performance liquid chromatography (UPLC) approach in pharmaceutical dosage forms. The small number of analytical studies that are currently available do not demonstrate the method's stability or nature. The study sought to assess both chemicals using a stability-indicating approach with a relatively short run time. The HSS C18 (100 × 2.1 mm), 2-mm column was used for the chromatographic separation, and isocratic elution was used to achieve this. In the mobile phase, methanol and 0.01 M phosphate buffer (pH 4.0) were included in a 60:40 (v/v) ratio. Throughout the analysis, the flow rate was kept at 0.2 mL min-1 , and a photodiode array detector set to 266 nm was used to find the major components. The proposed method showed a linear response (r2  > 0.999), and the accuracy was between 98.0% and 102.0%. The precision data showed relative standard deviation ≤1.0%. The UPLC method for quantification of ritonavir and darunavir in pharmaceutical dosage forms using a very short run time of under a minute is the subject of the proposed article. To meet current regulatory criteria, the quality by design idea was used in the method performance verification.

Valbenazine isomers and enantiomer determination by chiral normal phase liquid chromatography.

A novel, simple, specific, rapid, enantioselective normal phase chiral high-performance liquid chromatographic method with amylose-based Chiral Pak IG-3(250 × 4.6 mM) 3.0 µM column was developed and validated for separation and quantification of isomers and enantiomer of Valbenazine. The mobile phase composed of n-Heptane, isopropyl alcohol, dichloromethane, ethanol, and diethylamine in the ratio of 70:10:15:5:0.1 (V/V/V/VV) with a gradient flow rate was applied. The injection volume was 10 µl, and detection was carried out using a photodiode array detector at 282 nM. The column compartment was set at 35°C. The resolution between the enantiomer and isomers was found to be more than 2.0. The method was linear over the concentration range of limit of quantitation to 250% for isomers and enantiomers. The method was found to be robust with column temperature. The proposed chiral method is applicable for the determination of isomers and enantiomer of Valibenazine and was successfully used in the quality control of bulk drug manufacturing and pharmaceuticals.

Regulatory Perspective Reverse Engineering Analysis of the Mast Cell Stabilizer and the Histamine Receptor Antagonist (Olopatadine HCl): Instrumental and Classical Methods for Multiple Formulations.

This study evaluates the unknown qualitative (Q1) and quantitative (Q2) formulas for nasal spray and ophthalmic solution formulations of olopatadine HCl by classical and instrumental techniques to match the generic formula with reference-listed drugs to avoid clinical study. Reverse engineering of olopatadine HCl nasal spray 0.6% and ophthalmic solution 0.1, 0.2% formulations was accurately quantified using a simple and sensitive reversed-phase high-performance liquid chromatography (HPLC) method. Both formulations possess similar components, namely ethylenediaminetetraacetic acid (EDTA), benzalkonium chloride (BKC), sodium chloride (NaCl), and dibasic sodium phosphate (DSP). These components were qualitatively and quantitatively determined using the HPLC, osmometry, and titration techniques. With derivatization techniques, EDTA, BKC, and DSP were determined by ion-interaction chromatography. NaCl in the formulation was quantified by measuring the osmolality and using the subtraction method. A titration method was also used. All the employed methods were linear, accurate, precise, and specific. The correlation coefficient was >0.999 for all components in all the methods. The recovery results ranged from 99.1 to 99.7% for EDTA, 99.1-99.4% for BKC, 99.8-100.8% for DSP, and 99.7-100.1% for NaCl. The obtained % relative standard deviation for precision was 0.9% for EDTA, 0.6% for BKC, 0.9% for DSP, and 1.34% for NaCl. The specificity of the methods in the presence of other components, diluent, and the mobile phase was confirmed, and the analytes were specific.

Estimation of purity of antimicrobial lead compound sulfonamide-anthranilate derivative methyl-ester-toluene-sulfonamide using LC to develop a new drug application.

The newly synthesized lead molecule methyl-ester-toluene-sulfonamide is the combined derivative of sulfonamide-anthranilate. It was estimated by gradient elution using 0.1% triethylamine in water with pH 2.0 as mobile phase A and the mixture of acetonitrile and tetrahydrofuran in the ratio of 975:25 (v/v) as mobile phase B at a flow rate of 0.8 ml/min and 210 nm wavelength on an Agilent 1260 infinity series HPLC system equipped with a diode array detector. The column used was ACE 3 C18-PFP (250 × 4.6 mm, 3 µm i.d.) operating at 40°C. The gradient program was time (min)/% B: 0.0/50, 3.0/50, 15.0/70, 25.0/90, 30.0/90, 31/50, and 38/50. The method is simple, accurate, rapid, and selective. The method was linear with a concentration range of 1.6-240 µg/ml. The accuracy data obtained were 98.5-100.5%. The method validation data and quality by design-based robustness study results indicate that the developed method is robust and fit for routine use in the quality control laboratory. Therefore, the ready availability of the method can be useful in pharmaceutical new drug development.

Determination and quantification of related substances and degradation products in bictegravir by full factorial design evaluated HPLC and mass spectrometry.

Determining and quantifying novel impurities and degraded impurities of a drug product is always a continuous challenge to enhancing the drug quality for patients' safety. Herein, our work deals with (i) developing a rapid, accurate, and reliable high-performance liquid chromatographic validation method to quantify the bictegravir drug (integrase inhibitors of antiretroviral drugs) and its novel related impurities at low levels, and (ii) the liquid chromatography-mass spectrometry (LC-MS) method to identify degraded impurities. Separation of bictegravir acid (impurity-I) and methyl bictegravir (impurity-II) impurities which are identified by LC-MS in the bictegravir drug was executed by developing a method and the same method performance evaluated by using full factorial design. This developed analytical technique gave a well-separated peak of bictegravir and related analytes such as bictegravir acid (impurity-I) and methyl bictegravir (impurity-II), adequate with the peak properties as per USP guidelines. The method's sensitivity and linearity are demonstrated by its detection and quantification limits at low levels with a correlation coefficient of 0.998. The method's repeatability, specificity, and accuracy suggest that this developed technique is a reliable determination strategy for the bictegravir drug substance and its related impurities (impurity-I and impurity-II) in a simple, feasible, and affordable way.

QbD-based stability-indicating liquid chromatography (RP-HPLC) method for the determination of flurbiprofen in cataplasm.

A nonsteroidal drug called flurbiprofen (FBN) has analgesic, anti-inflammatory and antipyretic activity. Currently the determination of FBN in cataplasm does not have any pharmacopeial method. However, the drug substance, tablet and ophthalmic solution formulations do have pharmacopeial methods. The development and validation of an accurate, precise and stability-indicating analytical method for the determination of FBN in cataplasm formulations is reported. The gradient method was employed for the quantification of FBN in the presence of internal standards such as biphenyl. A nonpolar separation phase (C18 , 250 × 4.6 mm, 5 µm Inertsil column; GL Sciences) was used. The optimal flow rate, column oven temperature, injection volume and detector wavelengths were 1.0 ml/min, 40°C, 20 µl and 245 nm, respectively. Mobile phase A was a mixture of water and glacial acetic acid (30:1 v/v) pH adjusted to 2.20 with glacial acetic acid or 1 m NaOH; mobile phase B was methanol (100%). The gradient elution program was [time (min)/% B]: 5/60, 20/70, 25/70, 30/60 and 40/60. The obtained RSDs for the precision and intermediate precision were 0.7 and 0.5%. The percentage recovery ranged from 99.2 to 100.4%. The linear regression coefficient >0.9996 indicates that all peak responses were linear with the concentration. The sample and standard solutions were stable for up to 24 h on the benchtop and in the refrigerator. The critical peaks were well separated from the generated peaks owing to forced degradation, including diluent and placebo peaks. The method validation data and quality by design-based robustness study results indicate that the developed method is robust and fit for routine use in the quality control laboratory. The proposed method is specific, accurate and precise, and the quality by design utilized the first method for the determination of FBN in cataplasm formulations. Transdermal patches and gels have low extraction capacity and this method is applicable for quantification.

Development and validation of apalutamide-related substances method in solid dosage forms using HPLC.

A related-substances method was developed for the anticancer drug formulation apalutamide 60 mg tablets and validated using a liquid chromatography gradient elution method. All of the impurities and degradants were separated using the Luna Omega 5 µm Polar C18 , (250 × 4.6) mm HPLC column with a 1.0 ml min-1 flow rate. The detection was done at 225 nm by injecting the 10 µl of injection volume, controlling the sample temperature at 10°C and maintaining the column compartment temperature at 30°C. The total run time was 85 min. A 0.01 m disodium phosphate dihydrate pH 4.20 ± 0.05 buffer mixed with acetonitrile in the ratio of 73:27 (v/v) was used as mobile phase A. Mobile phase B consisted of water and acetonitrile in the ratio 30:70 (v/v). The proposed method was validated as per the current regulatory guidelines. The method precisions (RSD) at 100% specification level were 1.41, 1.74, 1.84, and 1.66% for the four impurities. The accuracy results were obtained between 96.0 and 106.3% for the limit of quantitation to the 150% level. The standard and sample solutions stability were established for 44 h at 10°C. The correlation coefficient (r) value was >0.999 for all four impurities, indicating good linearity between the concentration and peak response: 0.9999, 0.9999, 0.9999 and 1.0000. These results show the method's linearity. The three filter compatibility was proved and it was concluded that 0.45 µm Nylon, PTFE and PVDF filters are suitable. The robustness of the method was established by varying the conditions. The method specificity was proved and the forced degradation data reveal the method's stability-indicating nature.

A combined qualitative and quantitative method development and validation of vancomycin hydrochloride injection formulation by HPLC and UV involving quality by design.

A selective, specific, precise, linear, accurate and robust analytical method was developed and validated for the assay of vancomycin HCl in vancomycin hydrochloride injection. Comparative UV spectrophotometric and reverse-phase HPLC were used to develop the quantitative determination. Acetonitrile and pH 2.2 phosphate buffer in the ratio 20:80 v/v were used as the mobile phase, and a flow rate of 1.0 ml/min with a 20 min run time. The detection was carried out at 235 nm with a Nucleosil C18 (250 × 4.6 mm) 10 µm column, and the ambient column temperature was maintained. The method uses a 20 µl injection volume and diluent as a blank solution in this connection. The method was validated as per the current regulatory guidelines. The linearity of this method was found to be linear in the range of 50-150% of the working concentration, and the correlation coefficient was >0.999. The method's accuracy was within the acceptable range, which was 98.1-101.5%. The method's precision was within an acceptable range of about 0.32% RSD. The analytical solution was stable for up to 48 h at room temperature. The method's robustness was proved by utilizing quality design tools. Stress studies demonstrated the method's stability-indicating nature.

Stability-Indicating RP-HPLC Method Development and Validation for Eltrombopag Olamine in the Presence of Impurities and Degradation Products. Robustness by Design of Expert Software.

BACKGROUND: A simple and reliable HPLC method for determining impurities in eltrombopag olamine (ELO) film-coated tablets is not available. At the same time, there is no official monograph reported. The proposed research is targeted at the development of a stability-indicating method for determining impurities in ELO film-coated tablets and drug substances. OBJECTIVE: To develop and validate a simple and effective HPLC method for determining impurities in ELO film-coated tablets and drug substances. METHODS: All the impurities were separated using a reverse phase (RP)-HPLC system equipped with a Zorbax SB-Phenyl 150 mm × 4.6 mm, 3.5 µm, column with UV detection at 230 nm and a flow rate of 1.2 mL/min. The column temperature was maintained at 45°C. RESULTS: The proposed method was validated as per current regulatory guidelines. The coefficient of correlation was found to be >0.999 for all impurities. The LOD and LOQ for ELO and all specified impurities were determined. The precision and accuracy were obtained for ELO and its related impurities. Intra- and inter-day RSD values were between 1.22 and 2.04%, and impurity recovery varied between 93.80 and 103.69%. The stability of standard and sample solutions was established for 24 h. CONCLUSIONS: As per recent guidelines, a stability-indicating method has been developed to determine the impurities in ELO film-coated tablets and drug substances. QbD-based robustness was performed and proved that the method was robust. HIGHLIGHTS: The proposed article is the first RP-HPLC method for determining impurities in ELO film-coated tablets and drug substances. The quality by design (QbD) concept was utilized to verify the method performance.

AQbD based green UPLC method to determine mycophenolate mofetil impurities and Identification of degradation products by QToF LCMS.

We report an ideal method for quantifying impurities in mycophenolate mofetil drug substances and their oral suspension preparations. We developed a systematic and eco-friendly analytical approach utilizing quality by design (QbD) and green chemistry principles. Initially, the critical method parameters (CMPs) were screened using a D-optimal design. The robust final method conditions were optimized using a systematic central composite design (CCD). Through graphical and numerical optimization, the protocol conditions were augmented. The pH of mobile phase buffer (25 mM KH2PO4) (MP-A), initial gradient composition (% MP-A), flow rate (mL min-1), and column oven temperatures (°C) are 4.05, 87, 0.4, and 30, respectively. The best possible separation between the critical pairs was achieved while using the Waters Acquity UPLC BEH C18 (100 × 2.1) mm, 1.7 µm analytical column. A mixture of water and acetonitrile in the ratio of 30:70 (v/v) was used as mobile phase-B for the gradient elution. The analytical method was validated in agreement with ICH and USP guidelines. The specificity results revealed that no peaks interfered with the impurities and MPM. The mean recovery of the impurities ranged between 96.2 and 102.7%, and the linearity results r > 0.999 across the range of LOQ - 150%. The precision results (%RSD) ranged between 0.8 and 4.5%. The degradation products formed during the base-induced degradation were identified as isomers of mycophenolic acid and sorbitol esters using Q-ToF LC-MS and their molecular and fragment ion peaks. The developed method eco-friendliness and greenness were assessed using analytical greenness (AGREE), green analytical procedure index (GAPI), and analytical eco score, and found it is green.

Green Chromatographic Method for Determination of Active Pharmaceutical Ingredient, Preservative, and Antioxidant in an Injectable Formulation: Robustness by Design Expert.

We report an efficient HPLC method for simultaneous qualitative and quantitative analysis of lincosamide antibiotic injectable formulations containing Clindamycin phosphate (CMN), benzyl alcohol (BA), and ethylenediaminetetraacetic acid (EDTA) as major ingredients. The three components were separated by Phenomenex prodigy C8 (250 mm × 4.6 mm, 5 µm) HPLC column, flow rate 1.1 mL/min, injection volume 30 µL, and column temperature 35 °C, using 0.05 M sodium acetate buffer (pH 4.5) with acetonitrile (ACN) in the ratio of 80:20 (v/v). The detection wavelength was set as 240 nm. The method was validated as per International Conference on Harmonization (ICH) guidelines and was confirmed to be specific, precise, accurate, and linear. Method robustness was executed by utilizing quality in the design of the experiment. Accuracy results were found to be 99.3-100.5% for CMN, 99.3-100.8% for BA, and 99.1-100.3% for EDTA. Precision results were obtained as % relative standard deviation (RSD): 0.6% for CMN, 0.4% for BA, and 0.4% for EDTA. Correlation coefficient (r 2) values were obtained as >0.999 for the three components. Analytical solutions are stable for 48 h at benchtop and refrigerator conditions. The greenness of the analytical method was evaluated by the Green Analytical Procedure Index (GAPI), National Environmental Method Index (NEMI), analytical eco-scale, and Analytical Greenness (AGREE) tools to confirm that the method is eco-friendly.

Development and validation of novel RP-HPLC method for midostaurin determination using analytical quality by design approach from regulatory perspective and determination of major degradation compounds of midostaurin using LC-MS.

Midostaurin (MTN), designated as an orphan medicinal product, is emerging as an important drug for treating acute myeloid leukemia and advanced systematic mastocytosis. The proposed method was developed and validated to evaluate the related impurities of MTN. The impurities were separated using a YMC Trait C18 ExRS column (150 × 4.6 mm, 3 µm). Mobile phase A consisted of a 10-mM concentration of phosphate buffer adjusted to pH 3.0 with diluted orthophosphoric acid, and mobile phase B consisted of 90% acetonitrile and 10% water. The optimized chromatographic conditions were as follows: flow rate, 0.5 mL min-1 ; injection volume, 10 µL; UV detection, 290 nm; and linear gradient program, up to 65 min. The method was developed using an analytical quality by design approach. A systematic flow chart shows the evaluation, control, and life cycle management method. As part of method evaluation, risk assessment was conducted. The method has been validated per current guidelines of the International Conference on Harmonization. The recovery study and linearity ranges were established from the limit of quantification to 150% optimal concentrations. The recovery was found to be between 95.5 and 102.5%, and linearity (r2 ) was 0.9998-0.9999 for all the identified impurities. The method precision results were achieved below 10% of relative standard deviation. Forced degradation studies were performed under chemical and physical stress conditions. The compound was sensitive to chemical stress conditions. During the study, the analyte degraded and was converted into the identified degradation impurities, and its molecular mass was found using the LC-MS technique.

Unique liquid chromatography technique for the determination of mirabegron in the presence of polymers; robustness by Design Expert in the light of Quality by Design.

The current study is designed to estimate mirabegron in the presence of high molecular weight polymers using a unique liquid chromatography method and sample preparation technique. The proposed method is significant because of the many analytical issues faced during the development studies. Based on the experimental results, we finally achieved the stability-indicating power of the method. The adequately prepared mobile phase was in the ratio of pH 2.0 buffer and acetonitrile (80:20) v/v, and the buffer pH 2.0 was prepared as follows: 8.7 ml of perchloric acid, 2 ml of triethylamine and 3.0 g sodium hydroxide into 1 L of water mixed well. The system suitability parameters were achieved using a Waters X-Bridge C18 (4.6 × 150 mm, 3.5 µm) column and mobile phase. The optimized chromatographic conditions included a column temperature of 45°C, a flow rate of 1.0 ml min-1 ; an injection volume of 5 µl, UV 247 nm, and 15 min runtime. The method was validated and transferred to quality control as per International Conference on Harmonization Q2(R1) and the Chinese Pharmacopoeia 2020 edition <9101> and <9100>. The recovery and linearity results were obtained between 99.0 and 101.0%; the value of r2 was 0.9998. The method robustness study was established by utilizing the Design of Experiments part of the Quality by Design concept. The method's stability-indicating nature was proved by a forced degradation study; all of the conditions for analyte peak purity were passed, and mass balance was achieved. The method was used to determine mirabegron assay, as well as content uniformity, blend uniformity and cleaning samples. It is a user-friendly and cost-effective method.

Green Liquid Chromatography Method for the Determination of Related Substances Present in Olopatadine HCl Nasal Spray Formulation, Robustness by Design Expert.

BACKGROUND: Dual therapeutic nature drug mast cell stabilizer and histamine receptor antagonist olopatadine hydrochloride (OPT) nasal spray does not have an official monograph, and no literature is available. Eye drops formulation had the official monograph for impurities, but the determination was done in two methods. OBJECTIVE: A simple and effective green liquid chromatography method to develop and validate for the related substances of OPT nasal spray formulation. METHOD: A 25 min gradient method was employed to separate impurities and OPT with a 1.0 mL/min flow rate using a Boston green C8 (150 mm × 4.6 mm, 5 µm) HPLC column. The set wavelength and column oven temperatures were 299 nm and 30°C, respectively. pH 3.5 phosphate buffer-acetonitrile in the ratio of (70:30, v/v) as mobile phase A and (50:50, v/v) ratio as mobile phase B. A Quality by Design (QbD) based Design of Experiments (DoE) was employed to evaluate the robustness characteristics of the analytical method validation. RESULTS: The obtained RSD from the precision and intermediate precision was 0.4 to 4.1%. The % recovery of the impurities from LOQ to 150% of specification level was 87.5 to 110.3%. The linear regression curves for the impurities with a correlation coefficient of >0.999 indicate that all peak responses are linear with the concentration. The sample and standard solutions were stable for 24 h at benchtop and refrigerator conditions. CONCLUSIONS: All the critical peaks were well separated from the forced degradation studies' diluent, placebo, and generated degradation peaks. The method validation data and QbD based robustness study results indicate that the developed impurities method fits the routine quality control laboratory use. National Environmental Index (NMEI), Green Analytical Procedure Index (GAPI), Analytical Eco-scale and Analytical Greenness (AGREE) tools expressed the method's greenness. HIGHLIGHTS: The proposed method is QbD utilized and green chemistry assessed impurities determination method for OPT in nasal spray formulation.

Unique green chromatography method for the determination of serotonin receptor antagonist (Ondansetron hydrochloride) related substances in a liquid formulation, robustness by quality by design-based design of experiments approach.

Serotonin receptor antagonist drug Ondansetron hydrochloride injectable formulation containing all related substances was identified and quantified by a single, simple, sensitive, eco-friendly, and green high-performance liquid chromatography method. The disseverment of all impurities was achieved with the Discovery Cyano (250 × 4.6) mm, 5 µm column. The gradient program was composed of pH 5.7 phosphate buffer as mobile phase A and acetonitrile as mobile phase B. The flow rate, column compartment temperature, and detection wavelengths were 0.9 mL/min, 30°C, and 216 nm, respectively. The method was validated as per current regulatory guidelines. The obtained %relative standard deviation for the precision results was between 0.55 and 2.72% for all impurities. The correlation coefficient values from the linearity experiment for impurities and analyte were more than 0.995. The accuracy results were obtained between 88.4 and 113.0% for all impurities. Both sample and standard solutions showed 24 h stability at benchtop and refrigerator conditions. All impurities and analytes met the specificity and mass balance for all forced degradation conditions. Quality-by-design-based design of experiments was utilized to establish the method's robustness. Method greenness was assessed by using the current advanced tool green analytical procedure index, National Environmental Methods Index, and analytical eco-scale.