Posterior atlantoaxial fixation of osteoporotic odontoid fracture: biomechanical analysis of the Magerl versus harms techniques in a cadaver model.

BACKGROUND CONTEXT: Odontoid fractures are among the most common cervical spine fractures in the elderly and are associated with increased morbidity and mortality. Clinical evidence suggests improved survival and quality of life after operative intervention compared to nonoperative treatment. PURPOSE: This study seeks to examine the stability of an osteoporotic Type II odontoid fracture following posterior atlantoaxial fixation with either the Magerl transarticular fixation technique or the Harms C1 lateral mass screws C2 pedicle screw rod fixation. STUDY DESIGN: Biomechanical cadaveric study. METHODS: Eighteen cadaveric specimens extending from the cephalus to C7 were used in this study. Reflective marker arrays were attached to C1 and C2 and a single marker on the dens to measure movement of each during loading with C2-C3 and occiput-C1 being allowed to move freely. A biomechanical testing protocol imparted moments in flexion-extension, axial rotation, and lateral bending while a motion capture system recorded the motions of C1, C2, and the dens. The spines were instrumented with either the Harms fixation (n=9) or Magerl fixation (n=9) techniques, and a simulated Type II odontoid fracture was created. Motions of each instrumented spine were recorded for all moments, and then again after the instrumentation was removed to model the injured, non-instrumented state. RESULTS: Both Harms and Magerl posterior C1-C2 fixation allowed for C1, C2, and the dens to move as a relative unit. Without fixation the dens motion was coupled with C1. No significant differences were found in X, Y, Z translation motion of the dens, C1 or C2 during neutral zone motions between the Magerl and Harms fixation techniques. There were no significant differences found in Euler angle motion between the two techniques in either flexion-extension, axial rotation, or lateral bending motion. CONCLUSIONS: Our findings suggest that both Harms and Magerl fixation can significantly reduce dens motion in Type II odontoid fractures in an osteoporotic cadaveric bone model. CLINICAL SIGNIFICANCE: Both Harms and Magerl posterior atlantoaxial fixation techniques allowed for C1, C2, and the dens to move as a relative unit following odontoid fracture, establishing more anatomic stability to the upper cervical spine.

Characterization of regional variation of bone mineral density in the geriatric human cervical spine by quantitative computed tomography.

BACKGROUND: Odontoid process fractures are among the most common in elderly cervical spines. Their treatment often requires fixation, which may include use of implants anteriorly or posteriorly. Bone density can significantly affect the outcomes of these procedures. Currently, little is known about bone mineral density (BMD) distributions within cervical spine in elderly. This study documented BMD distribution across various anatomical regions of elderly cervical vertebrae. METHODS AND FINDINGS: Twenty-three human cadaveric C1-C5 spine segments (14 males and 9 female, 74±9.3 y.o.) were imaged via quantitative CT-scan. Using an established experimental protocol, the three-dimensional shapes of the vertebrae were reconstructed from CT images and partitioned in bone regions (4 regions for C1, 14 regions for C2 and 12 regions for C3-5). The BMD was calculated from the Hounsfield units via calibration phantom. For each vertebral level, effects of gender and anatomical bone region on BMD distribution were investigated via pertinent statistical tools. Data trends suggested that BMD was higher in female vertebrae when compared to male ones. In C1, the highest BMD was found in the posterior portion of the bone. In C2, BMD at the dens was the highest, followed by lamina and spinous process, and the posterior aspect of the vertebral body. In C3-5, lateral masses, lamina, and spinous processes were characterized by the largest values of BMD, followed by the posterior vertebral body. CONCLUSIONS: The higher BMD values characterizing the posterior aspects of vertebrae suggest that, in the elderly, posterior surgical approaches may offer a better fixation quality.

Relationship to drill bit diameter and residual fracture resistance of the distal tibia.

BACKGROUND: The etiology of bone refractures after screw removal can be attributed to residual drill hole defects. This biomechanical study compared the torsional strength of bones containing various sized cortical drill defects in a tibia model. METHODS: Bicortical drill hole defects of 3 mm, 4 mm, and 5 mm diameters were tested in 26 composite tibias versus intact controls without a drill defect. Each tibia was secured in alignment with the rotational axis of a materials testing system and the proximal end rotated internally at a rate of 1 deg./s until mechanical failure. FINDINGS: All defect test groups were significantly lower (P < 0.01) in torque-to-failure than the intact group (82.80 ± 3.70 Nm). The 4 mm drill hole group was characterized by a significantly lower (P = 0.021) torque-to-failure (51.00 ± 3.27 Nm) when compared to the 3 mm drill hole (59.00 ± 5.48 Nm) group, but not different than the 5 mm hole group (55.71 ± 5.71 Nm). All bones failed through spiral fractures, bones with defects also exhibited posterior butterfly fragments. INTERPRETATION: All the tested drill hole sizes in this study significantly reduced the torque-to-failure from intact by a range of 28.4% to 38.4%, in agreement with previous similar studies. The 5 mm drill hole represented a 22.7% diameter defect, the 4 mm drill hole a 18.2% diameter defect, and the 3 mm drill hole a 13.6% diameter defect. Clinicians should be cognizant of this diminution of long bone strength after a residual bone defect in their creation and management of patient rehabilitation programs.

Axial and Rotational Malreduction (Golf Club Deformity) in Distal Femur Fractures.

OBJECTIVES: To describe malreduction of supracondylar distal femur fractures stabilized with lateral femoral locking plates and determine whether a mismatch in axial lateral distal femur anatomy and lateral distal femoral plate design contributes to supracondylar distal femoral fracture malreduction. MATERIALS AND METHODS: OTA/AO 33A were simulated in 7 cadaver femurs and fixed with a lateral distal locking femoral plate placed flush to the lateral femoral condyle (group 1). In group 2, the anterior flange of the plate was externally rotated 10 degrees in relation to the lateral condyle. A motion capture system measured translation and rotation of the articular segment as shaft screws were applied, reducing plate to femoral diaphysis. Articular segment movement was compared between groups using paired Student t test, P < 0.05. A large database of 3D scans of 800 femurs was used to define the relationship of the lateral femoral condyle to the lateral cortical surface of the human femur. RESULTS: Malreduction was observed with anatomic plate application results from medial translation (17 mm) and external rotation (12.2 degrees) (group 1). Modifying plate geometry to match lateral femur anatomy (group 2) improved medial translation by 46% and external rotation by 80%. An analysis of the shape of the 800 distal femurs showed that the average posterior anterior inclination is 16.5 degrees. CONCLUSIONS: Anatomic application of distal femoral plates results in significant malreduction. Modifying the plate design to accommodate 10 degrees slope of lateral distal femur results in partial correction of deformity. Future studies should investigate other means of correcting the malalignment, especially considering the 16.5-degree posterior anterior inclination of the condyle.

How Does Tibial Pin Placement in Navigated Total Knee Arthroplasty Affect the Torsional Strength of the Tibia?

INTRODUCTION: Surgical navigation technology has recently become more prevalent for total knee arthroplasty. Surgical navigation typically requires pin placement in the proximal tibia diaphysis to stabilize the bone-tracking hardware, and there have been several recent reports of fractures through these residual navigation pin holes. The objective of this biomechanical study was to determine whether a difference exists in the torsional bone strength of a 5-mm navigation pin hole drilled at a single location in three different orientations: unicortical, bicortical, and transcortical. METHODS: Biomechanical composite sawbone tibias were used to test four conditions: the intact condition with no holes, a unicortical hole, a bicortical hole, and a transcortical hole through the proximal diaphysis. Seven specimens from each group were tested in external rotation to failure at 1 deg/sec. Torque-to-failure, absorbed energy-to-failure, and rotational angle-to-failure were statistically compared across the four groups. RESULTS: All specimens failed proximally by spiral oblique fractures. No statistical differences were found between unicortical and bicortical groups in torque-to-failure, energy-to-failure, and angle-to-failure. However, both unicortical and bicortical groups were markedly lower in all measures than the intact group. The transcortical group was markedly lower in all measures than the intact group and both unicortical and bicortical groups. DISCUSSION: An appropriately placed navigation residual pin hole, either unicortical or bicortical, markedly decreases the torque-to-failure, energy-to-failure, and angle-to-failure of the tibia compared with the intact condition in a synthetic sawbones model. No notable difference was detected between the unicortical and bicortical holes; however, an errant transcortical residual navigation pin hole markedly decreases all measures compared with an appropriately placed unicortical or bicortical hole.

Does coating an intramedullary nail with polymethylmethacrylate improve mechanical stability at the fracture site?

BACKGROUND: Treatment of tibia diaphyseal fractures with intramedullary nail fixation has proven to be effective. An increasingly popular practice is to coat the nail with bone cement incorporating antibiotics for the purpose of treating and/or preventing infection. To date, the effect of coating on the mechanical performance of the intramedullary nail once implanted is unknown. We hypothesize that cement coating does not change the cross-sectional stiffness of the nail, so that, when fixing tibia diaphyseal fracture with gapping, cement coated intramedullary nail provide stiffness comparable to that of standard conventional uncoated ones. METHODS: Tests of 4-point bending were conducted to compare the cross-sectional stiffness of uncoated to coated nails. In addition, mechanical tests of compression and torsion on tibia bone phantoms instrumented with coated and uncoated nails were performed, and the proximal-to-distal bone fragment rotations were compared. FINDINGS: The 4-point bending tests indicated that the cross-sectional stiffness of coated nails was not significantly different from that of the uncoated ones (p-value >0.05). Mechanical tests of compression and torsion corroborated these results by showing no statistical difference in the proximal-to-distal bone rotations attained with uncoated nails when compared to those measured for the coated ones (p-value >0.05). INTERPRETATION: Cement coating on the nail cannot be relied upon for increased mechanical stiffness of the implant, and should be solely considered as a vehicle for topic delivery of antibiotics.

Mechanical performance and implications on bone healing of different screw configurations for plate fixation of diaphyseal tibia fractures: a computational study.

Diaphyseal tibia fractures may require plate fixation for proper healing to occur. Currently, there is no consensus on the number of screws required for proper fixation or the optimal placement of the screws within the plate. Mechanical stability of the construct is a leading criterion for choosing plate and screws configuration. However, number and location of screws have implications on the mechanical environment at the fracture site and, consequently, on bone healing response: The interfragmentary motion attained with a specific plate and screw construct may elicit mechano-transduction signals influencing cell-type differentiation, which in turn affects how well the fracture heals. This study investigated how different screw configurations affect mechanical performance of a tibia plate fixation construct. Three configurations of an eight-hole plate were considered with the fracture in the center of the plate: eight screws-screws at first, fourth, fifth and eighth hole and screws at first, third, sixth and eighth hole. Constructs' stiffness was compared through biomechanical tests on bone surrogates. A finite element model of tibia diaphyseal fracture was used to conduct a stress analysis on the implanted hardware. Finally, the potential for bone regeneration of each screw configuration was assessed via the computational model through the evaluation of the magnitude of mechano-transduction signals at the bone callus. The results of this study indicate that having screws at fourth and fifth holes represents a preferable configuration since it provides mechanical properties similar to those attained by the stiffest construct (eight screws), and elicits an ideal bone regenerative response.

A novel way to dynamize a spatial frame and optimize fracture healing.

BACKGROUND: Fracture site motion creates mechanical strains on the healing tissues which influences bone formation. Axial micro-motion maximizes dilatational strains, whereas shearing motions maximize deviatoric strains on the healing tissues. Dilatational strains optimize bone healing, deviatoric strains retard bone healing. Dynamization of external fixation using either an Ilizarov or Spatial Frame platform is used to increase loading on the limb which increases the mechanical stress and strain on the tissues to improve healing. The scientific literature does not address how dynamization of the spatial frame effects fracture site motion. The purpose of this study is to assess the effect of modified shoulder bolts incorporated into a spatial frame during dynamic loading. METHODS: Five identical two-ring spatial frame constructed were mounted on Sawbones tibias with an osteotomy performed distal to the tibial tubercle. Sinusoidal load was applied at a rate of 0.25 Hz. Axial force and displacement, in addition to motion of the proximal and distal tibia segments were recorded. Eight constructs were tested: 1) All struts of the Spatial Frame rigid, 2) Strut #1 loose, 3) Struts #1 and #3 loose, 4) Struts #1, #3 and #5 loose, 5) All struts loose, 6) All struts rigid with dynamization bolts on the proximal end, 7) All struts rigid with dynamization bolts on alternating sides, 8) Threaded rods between the rings with two millimeters of dynamization. RESULTS: No difference in vertical displacement was observed between the Ilizarov and all struts locked. No significant difference in shear values between all struts locked and modified shoulder bolt struts was observed. Increase in vertical movement with the modified shoulder bolts was an average of 1.83 mm. Significant shear forces at the fracture site were observed with unlocking single or multiple struts of the spatial frame. CONCLUSION: Modified shoulder bolts can be used for spatial frame dynamization without increasing shear motion.

Is it necessary to tie the medial row in rotator cuff repair double-row constructs when using suture tape?

PURPOSE: To evaluate the selected biomechanical differences of a double-row trans-osseous equivalent rotator cuff repair with a knotless versus knot-tying medial row using suture tape in regard to repair displacement, stiffness, and ultimate load to failure. METHODS: In 16 fresh-frozen human shoulders (8 matched pairs), double-row rotator cuff repairs were performed with medial-row mattress knots (MK) on one side, the other without (NK). Two DVRT (Differential Variable Reluctance Transducer) sensors were attached between the humerus and 3 mm above the repair site and were used to measure the displacement across the repair during cycling. The biomechanical parameters measured were repair displacement, stiffness, and ultimate load to failure. The supraspinatus was loaded in a similar fashion to previously described protocol using cyclic loading and load to failure testing.1. RESULTS: All data from paired specimens were compared using paired Student t tests. No statistically significant difference (SSD) in displacement across the repair over the 200 cycles of the test was noted between the two groups (MK = 0.591 ± 0.501 mm; NK = 0.439 ± 0.417 mm, p = 0.618). No SSD in stiffness was noted between the two groups (MK = 32.87 ± 6.31 N/mm; NK = 27.98 ± 9.69 N/mm, p = 0.120). No SSD in ultimate load to failure was noted between the two groups (MK = 501.2 ± 126.1 N; NK = 416.8 ± 120.0 N, p = 0.116). CONCLUSION: There was no statistically significant different between knotless versus knotted medial row double row rotator cuff repair constructs using suture tape in regard to displacement across the repair site, stiffness and ultimate load to failure. Despite previous evidence suggesting inferiority of knotless medial row technique using suture constructs, this evidence may support the biomechanical equivalency of knotless medial row technique using suture tape.

Effects of Lumbosacral Arthrodesis on the Biomechanics of the Sacroiliac Joint.

BACKGROUND: It is unclear whether the sacroiliac joint is vulnerable to adjacent segment disease. Clinical studies have suggested that many patients who have undergone lumbar arthrodesis will develop adjacent segment disease, which may contribute to sacroiliac joint degeneration. The purpose of the present study was to examine whether arthrodesis in the lumbar spine results in altered biomechanics at the sacroiliac joint that could contribute to adjacent segment disease within the joint. METHODS: With use of human cadavers in a biomechanical laboratory study, the effects of lower-lumbar arthrodesis and sacroiliac screws on the biomechanics of the sacroiliac joint were assessed. Human cadaveric pelves with lumbar spines were biomechanically tested in flexion-extension, rotation about the vertical axis, and compression along the vertical axis with single and double-leg support. Four conditions were compared: (1) intact, (2) L4-L5 arthrodesis, (3) L4-S1 arthrodesis, and (4) left sacroiliac screw. Construct vertical and horizontal motions at the anterior and posterior surfaces of the sacroiliac joint were measured. RESULTS: Significant measurable increases in motion of the sacroiliac joint related to arthrodesis of the lumbar spine occurred with flexion-extension loading (p < 0.05). No significant changes were observed for rotation about the vertical axis or compression along the vertical axis with single and double-leg support. CONCLUSIONS: After 360°, 1 or 2-level lumbosacral spine arthrodesis, the sacroiliac joint showed a significant increase in rotational motion with flexion-extension loading. Increases in horizontal translation with axial rotation loading and vertical translation with axial compression loading were not significant. CLINICAL RELEVANCE: The risk of significant alteration of normal sacroiliac kinematics should be considered in all patients undergoing 360° lumbosacral arthrodesis.

Comparison of Biomechanical Properties of a Synthetic L3-S1 Spine Model and Cadaveric Human Samples.

Human cadavers currently represent the gold standard for spine biomechanical testing, but limitations such as costs, storage, handling, and high interspecimen variance motivate the development of alternatives. A commercially available synthetic surrogate for the human spine, the Sawbones spine model (SBSM), has been developed. The equivalence of SBSM to a human cadaver in terms of biomechanical behavior has not been fully assessed. The objective of this study is to compare the biomechanics of a lumbar tract of SBSM to that of a cadaver under physiologically relevant mechanical loads. An L3-S1 SBSM and 39 comparable human cadaver lumbar spine tracts were used. Each sample was loaded in pure flexion-extension or torsion. Gravity and follower loads were also included. The movement of each vertebral body was tracked via motion capture. The range of motion (ROM) of each spine segment was recorded, as well as the overall stiffness of each L3-S1 sample. The ROM of SBSM L3-L4 was larger than that found in cadavers in flexion-extension and torsion. For the other spine levels, the ROMs of SBSM were within one standard deviation from the mean values measured in cadavers. The values of structural stiffness for L3-S1 of SBSM were comparable to those of cadaveric specimens for both flexion and torsion. In extension, SBSM was more compliant than cadavers. In conclusion, most of the biomechanical properties of an L3-S1 SBSM model were comparable to those of human cadaveric specimens, supporting the use of this synthetic surrogate for testing applications.

Biomechanical Comparison between Volar Plate Fixator and Nonbridge External Wrist Fixator.

Intra-articular distal radius fractures are difficult to reduce and maintain by nonoperative means. ORIF leaves implants in the patient long after the fracture is healed. External fixation can stabilize the reduced fracture and leaves no long-term implants. The nonbridging fixator (NBX) will provide better reduction and comparable rigidity of fixation to a volar plate for a 5-fragment, OTA 23 C3.2 distal radius fracture. A 5-part distal radius fracture was created in 5 pairs of cadaver arms. One arm was randomly fixed with the NBX fixator; the matched pair was fixed with a volar plate (VPS). Fluoroscopic images recorded the extremes of passive volar-dorsiflexion range of motion (ROM) and radial-ulnar deviation ROM. Each arm was loaded with an axial force at a constant displacement rate until failure. The average reduction of radial tilt achieved for the NBX group was 13.8 ± 4.8° and 6.3 ± 4.7° for VPS; radial length: 3.4 ± 3.7 mm for NBX and 1.9 ± 1.0 mm for VPS; volar tilt: 26.3 ± 12.4° for NBX and 14.0 ± 13.5° for VPS. For NBX, ROM was slightly less after fixation than before fracture. ROM with volar plating was greater after fracture. The peak axial load for NBX was 925 ± 445 N; for VPS, 2,152 ± 1023 N. NBX had minimal effect on ROM and provided adequate strength and restoration of alignment at least as good as VPS for this 5-part fracture model.

Cervical Spine Fusion: Biomechanics of a Three-Level Cadaver Model Comparing Anterior Plate versus Stand-Alone Cage.

Study Design-Biomechanical cadaveric study. Objective-Long anterior cervical plate and cage (APC) constructs have a risk of pseudarthrosis with minor bone resorption. Stand-alone cages (SACs) allow settling. The biomechanics of SAC have been investigated, but not multilevel, compression screw SAC. The purpose of this study is to evaluate the biomechanical safety of three-level SAC versus APC. Methods-Discectomies at three levels of five human cadaver spines (T1-C3) were fixed with SAC. A 0.18 mm thick shim was interposed between the cage and the superior endplate, and a pressure transducer map was placed between the cage and the inferior endplate. Tests were performed in flexion-extension and then repeated after removing the shims to simulate minor bone resorption. Subsequently, APC was applied and experiments were repeated. The pressure between each cage and endplate and motion of the implants were measured. Results-The range of motion (ROM) of SAC and APC constructs were comparable. The contact area and pressure between cage and endplate did not significantly change during motion with SAC. Shim removal did not significantly affect ROM, contact area, or average pressure measures. For APC, both contact area and pressure decreased from extension to flexion. Shim removal caused a significant loss of contact area and pressure. Conclusions-SAC provided comparable rigidity to the conventional APC construct while maintaining compression at the endplate-cage interface throughout flexion-extension and after minor bone resorption.

Treatment of Selected Distal Radius Fractures with Nonbridging External Fixation.

A nonbridging external fixation (NBX) system with 1.6-mm diameter pins provided excellent stability for distal radius fractures in cadavers. For the present study, all patients with distal radius fractures were seen by the surgeon authors. Fractures that were displaced and unstable, including Orthopaedic Trauma Association (OTA) types 23-A2.3 to C3.3, were reduced and fixed with the NBX system. The Western Institutional Review Board granted approval (296864) for this retrospective study. Fractures numbered five OTA-A2, eight OTA-A3, two OTA-B3, one OTA-C1, two OTA-C2, and eight OTA-C3. In total, the study included 26 patients. At fixator removal, average dorsiflexion was 37.0° ± 17.8°; volar flexion, 39.4° ± 17.2°; pronation, 80.6° ± 16.1°; and supination, 48.1° ± 24.2°. Follow-up averaged 11.7 mo ± 19.2 mo. At final follow-up, average dorsiflexion was 52.9° ± 25.0°; volar flexion, 53.1° ± 23.7°; pronation, 80.8° ± 14.5°; and supination, 67.7° ± 30.3°. Average radial tilt at the time of injury was 11.6° ± 8.3°; post op to 23.9° ± 5.0°; and at last follow-up, 23.1° ± 5.0°. Average radial styloid length at the time of injury was 4.1 mm ± 3.7 mm; post op to 11.4 mm ± 3.0 mm; and at last follow-up, 10.5 mm ± 3.1 mm. Volar tilt at the time of injury averaged -19.6° ± 14.8°; reduced to 9.8° ± 6.3°; and at last follow-up, 7.5° ± 6.5°. This form of nonbridging fixation is safe and effective at maintaining reduced, extra- and intra-articular, distal radius fractures and allows functional range of motion with minimal complications.

Relationships Among Bone Morphological Parameters and Mechanical Properties of Cadaveric Human Vertebral Cancellous Bone.

Mechanical properties and morphological features of the vertebral cancellous bone are related to resistance to fracture and capability of withstanding surgical treatments. In particular, vertebral strength is related to its elastic properties, whereas the ease of fluid motion, related to the success of incorporation orthopedic materials (eg, bone cement), is regulated by the hydraulic permeability (K). It has been shown that both elastic modulus and permeability of a material are affected by its morphology. The objective of this study was to establish relations between local values of K and the aggregate modulus (H), and parameters descriptive of the bone morphology. We hypothesized that multivariate statistical models, by including the contribution of several morphology parameters at once, would provide a strong correlation with K and H of the vertebral cancellous bone. Hence, µCT scans of human lumbar vertebra were used to determine a set of bone morphology descriptors. Subsequently, indentation tests on the bone samples were conducted to determine local values of K and H. Finally, a multivariate approach supported by principal component analysis was adopted to develop predictive statistical models of bone permeability and aggregate modulus as a function of bone morphology descriptors. It was found that linear combinations of bone volume fraction, trabecular thickness, trabecular spacing, structure model index, connectivity density, and degree of anisotropy provide a strong correlation (R 2 ~ 76%) with K and a weaker correlation (R 2 ~ 47%) with H. The results of this study can be exploited in computational mechanics frameworks for investigating the potential mechanical behavior of human vertebra and to develop strategies to treat or prevent pathological conditions such as osteoporosis, age-related bone loss, and vertebral compression fractures. © 2020 The Authors. JBMR Plus published by Wiley Periodicals, Inc. on behalf of American Society for Bone and Mineral Research.

Cerclage Cable Tensioning of Intraoperative Hip Arthroplasty Proximal Femoral Fractures: A Cadaveric Model.

Cerclage fixation following intraoperative fracture of the proximal femur during total hip arthroplasty (THA) carries a risk of compromising the femoral blood supply. Thus, we sought to determine the minimum cerclage cable tension required to restore the stability of a cementless femoral stem. Cementless femoral prostheses were implanted in seven proximal femoral cadaver specimens, and a periprosthetic fracture was simulated in the medial cortex. A single cerclage cable was placed just above the lesser trochanter and tensioned and tested at increasing intervals. The implant's torsional stability was determined in the intact bone, prior to fixation, and at each level of cable tension. We found that a single cerclage cable placed above the lesser trochanter can significantly improve, but not fully restore, torsional stability following intraoperative periprosthetic femur fracture during THA. The optimal position for a single cerclage cable appears to be above the lesser trochanter. (Journal of Surgical Orthopaedic Advances 29(4):209-211, 2020).

Diagnosis of Traumatic Ankle Arthrotomies Using Saline Load Tests, Methylene Blue, and Radiopaque Tracer: A Cadaveric Study.

BACKGROUND: The objective of this study was to define the volume (mLs) needed for a positive saline load challenge test in anterolateral (AL), anteromedial (AM), posterolateral (PL), or posteromedial (PM) ankle arthrotomy wounds using normal saline (NS) and methylene blue (MB). Another objective was to evaluate the use of fluoroscopy and iodinated contrast in the diagnosis of ankle arthrotomies. METHODS: Four cadaveric ankle specimens underwent standardized arthrotomy creation in either the AL, AM, PL, or PM portion of each specimen. An 18-gauge needle was used to inject fluid into each ankle, and the volumes needed for positive fluid challenges were recorded. All 4 ankles were tested 10 times (n = 40) with NS and 10 times using MB (n = 40). A fifth cadaveric ankle was injected with radiopaque contrast solution, and an arthrotomy was simulated and imaged with fluoroscopy.Statistical analyses compared the volumes of NS and MB needed for a positive test. In addition, the 25th, 50th, 75th, 90th, and 95th percentiles of volumes needed for a positive test was calculated. RESULTS: The volume of fluid necessary to detect 25%, 50%, 75%, 90%, and 95% of ankle arthrotomies from any site was 2.0 mL, 4.5 mL, 9.0 mL, 10 mL, and 10 mL, respectively. Anterior arthrotomies required less fluid (2.1 mL ± 0.5) than posterior arthrotomies (9.0 mL ± 1.2) for a positive test (P < .0001). There was no difference between the amount of NS (5.5 mL ± 3.6) vs MB (5.6 mL ± 3.7) needed for a positive challenge test (P = .739). CONCLUSION: Ninety-five percent of ankle arthrotomies could be diagnosed with 10 mL of injected fluid; there was no difference between the volume of NS vs MB needed. Fluoroscopy assisted with needle placement and can be combined with radiopaque contrast solution to diagnose ankle arthrotomies. CLINICAL RELEVANCE: The findings of this study may improve sensitivity and efficiency in the diagnosis of traumatic ankle arthrotomies, for which there is currently a paucity of literature.

Supplemental Fixation of Inner Graft Limbs in All-Inside, Quadrupled, Single-Tendon Anterior Cruciate Ligament Reconstruction Graft Construct Yields Improved Biomechanical Properties.

PURPOSE: To compare the time-zero load to failure of a quadrupled, single-tendon, all-inside anterior cruciate ligament (ACL) reconstruction graft construct with (supplemented) and without the incorporation of inner-limb whipstitch sutures (control) into a tibial suspensory fixation button. METHODS: Eight matched pairs of peroneus longus tendons were prepared according to a quadrupled, all-inside ACL soft-tissue graft technique with 1 side serving as a control and the contralateral side supplemented. The constructs were biomechanically tested for strain in the inner and outer limbs during a preconditioning protocol, single-cycle load to failure, and elongation of the whole construct. RESULTS: Ultimate load to failure was significantly higher in the supplemented group: 797.5 ± 49.6 N (95% confidence interval [CI], 763.13-831.87 N) versus 719.6 ± 69.6 N (95% CI, 671.38-767.82 N; P = .044). Less graft elongation at failure was observed in the supplemented group (3.1 ± 1.5 mm; 95% CI, 2.07-4.17 mm) versus the control group (21.0 ± 21.2 mm; 95% CI, 6.31-35.69 mm; P = .052). The number of grafts undergoing a 5-mm or greater change in length at failure was 1 of 8 in the supplemented group versus 5 of 8 in the control group (P = .038). CONCLUSIONS: Inner-limb supplemental tibial fixation results in higher time-zero load to failure and decreased graft elongation in a quadrupled, single-tendon, all-inside ACL reconstruction graft construct. CLINICAL RELEVANCE: The weak point of a single-tendon, quadrupled, all-inside ACL graft construct is the tendon-to-tendon suturing to secure the inner limbs of the graft. Adding supplemental fixation by incorporating the sutures from the inner limb to the tibial suspensory fixation button leads to a higher time-zero load to failure and decreased graft elongation.

Filling Open Screw Holes in the Area of Metaphyseal Comminution Does Not Affect Fatigue Life of the Synthes Variable Angle Distal Femoral Locking Plate in the AO/OTA 33-A3 Fracture Model.

INTRODUCTION: The aim of this study is to evaluate the biomechanical effect of filling locking variable angle (VA) screw holes at the area of metaphyseal fracture comminution in a Sawbones® (Sawbones USA, Vashon, Washington) model (AO/OTA 33A-3 fracture) using a Synthes VA locking compression plate (LCP) (Depuy Synthes, Warsaw, Indiana). MATERIALS AND METHODS: Seven Sawbones® femur models had a Synthes VA-LCP placed as indicated by the manufacturers technique. A 4cm osteotomy was then created to simulate an AO/OTA 33-A3 femoral fracture pattern with metaphyseal comminution. The control group consisted of four constructs in which the open screw holes at the area of comminution were left unfilled; the experimental group consisted of three constructs in which the VA screw holes were filled with locking screws. One of the control constructs was statically loaded to failure at a rate of 5mm/min. A value equal to 75% of the ultimate load to failure was used as the loading force for fatigue testing of 250,000 cycles at 3Hz. Cycles to failure was recorded for each construct and averages were compared between groups. RESULTS: The average number of cycles to failure in the control and experimental groups were 37524±8187 and 43304±23835, respectively (p=0.72). No significant difference was observed with respect to cycles to failure or mechanism of failure between groups. In all constructs in both the control and experimental groups, plate failure reproducibly occurred with cracks through the variable angle holes in the area of bridged comminution. CONCLUSIONS: The Synthes VA-LCP in a simulated AO/OTA 33-A3 comminuted metaphyseal femoral fracture fails in a reproducible manner at the area of comminution through the "honeycomb" VA screw holes. Filling open VA screw holes at the site of comminution with locking screws does not increase fatigue life of the Synthes VA-LCP in a simulated AO/OTA 33-A3 distal femoral fracture. Further studies are necessary to determine whether use of this particular plate is contraindicated when bridging distal femoral fractures with metaphyseal comminution.

How Reliable is the Acetabular Cup Position Assessment from Routine Radiographs?

BACKGROUND: Cup position is crucial for optimal outcomes in total hip arthroplasty. Radiographic assessment of component position is routinely performed in the early postoperative period. AIMS: The aims of this study were to determine in a controlled environment if routine radiographic methods accurately and reliably assess the acetabular cup position and to assess if there is a statistical difference related to the rater's level of training. METHODS: A pelvic model was mounted in a spatial frame. An acetabular cup was fixed in different degrees of version and inclination. Standardized radiographs were obtained. Ten observers including five fellowship-trained orthopaedic surgeons and five orthopaedic residents performed a blind assessment of cup position. Inclination was assessed from anteroposterior radiographs of the pelvis and version from cross-table lateral radiographs of the hip. RESULTS: The radiographic methods used showed to be imprecise specially when the cup was positioned at the extremes of version and inclination. An excellent inter-observer reliability (Intra-class coefficient > 0,9) was evidenced. There were no differences related to the level of training of the raters. CONCLUSIONS: These widely used radiographic methods should be interpreted cautiously and computed tomography should be utilized in cases when further intervention is contemplated.