RESUMEN
The introduction of macroporous structures into three-way catalysts (TWCs) through polymer template-assisted spray drying has attracted attention because of its enhanced gas diffusion and catalytic performance. However, the surface charge effect of polymeric template components has not been investigated to control the structure of the TWC particles during synthesis. Thus, this study investigated the effect of template surface charges on the self-assembly behavior of TWC nanoparticles (NPs) during drying. The self-assembly of TWC NPs and polymer particles with different charges produced a hollow structure, whereas using the same charges generated a porous one. Consequently, the mechanism of particle self-assembly during drying and final structure particle formation is proposed in this study. Here, porous TWC particles demonstrated a faster oxidation of soot particles than that of hollow-structured particles. This occurred as a result of the larger contact area between the catalyst surface and the solid reactant. Our findings propose a fundamental self-assembly mechanism for the formation of different TWC structures, thereby enhancing soot oxidation performance using macroporous structures.
RESUMEN
In recent years, transportation-related air pollution has escalated into a global concern, necessitating the development of a three-way catalyst (TWC) technology to address harmful emissions. However, the efficiency of TWC's performance in mitigating these emissions has been hindered because of limited mass transfer efficiency within their structures. Thus, this study attempted to overcome the existing issue by synthesizing a series of macroporous TWC particles exhibiting various macropore sizes via a template-assisted spray process, aiming to achieve optimal mass transfer efficiency and catalytic performance. The synthesis incorporated various template particles (size of 67-381 nm) to obtain various macroporous structures. Thereafter, these macroporous particles were assessed for their carbon monoxide (CO) oxidation performance, revealing a substantial influence of the macropore size on the catalytic performance of TWC structures. Interestingly, among the investigated samples, those containing the smallest and largest macropores demonstrated the highest CO oxidation performances. Based on these results, a plausible reactant diffusion mechanism was proposed to explain the effect of the macropore size on the diffusion efficiency within the macroporous structures. This work may have significant implications in optimizing the macroporous structure to enhance catalytic performance in the gas purification process.
RESUMEN
Mass transfer is an essential process that can extend the performance and utilization of nanoporous materials in various applications. Therefore, improving mass transfer in nanoporous materials has always attracted much interest, and macroporous structures are currently being studied to enhance mass transfer performance. The introduction of macroporous structures into three-way catalysts (TWC), which are widely utilized to control the emission of polluted gases from vehicles, provides the potential to enhance their mass transfer property and catalytic performance. However, the formation mechanism of macroporous TWC particles has not yet been investigated. On the other hand, the influence of the framework thickness of the macroporous structure on the mass transfer enhancement is still unclear. Therefore, this report investigates the particle formation and framework thickness of the macroporous TWC particles synthesized using the template-assisted aerosol process. The formation of macroporous TWC particles was precisely controlled and investigated by altering the size and concentration of the template particles. The template concentration played a crucial role in maintaining the macroporous structure and controlling the framework thickness between the macropores. Based on these results, a theoretical calculation showing the influence of template concentration on the particle morphology and framework thickness was developed. The final results showed that increasing the template concentration can positively affect the nanoporous material's framework thickness reduction and mass transfer coefficient improvement.
RESUMEN
A green synthetic strategy to design biomass-derived porous carbon electrode materials with precisely tailored structure and morphology has always been a challenging goal because these materials can fulfill the demands of next-generation supercapacitors and other electrochemical devices. Potassium hydroxide (KOH) is extensively utilized as an activator since it can produce porous carbon with high specific surface area and well-developed porous channels. The exploitation of sodium hydroxide (NaOH) as an activating agent is less referenced in the literature, although it offers some advantages over KOH in terms of low cost, less corrosiveness, and simple handling procedure, all of which are appealing particularly from an industrial viewpoint. The motivation for this present study is to fabricate porous carbon spheres in a sustainable manner via a spray drying approach followed by a carbonization process, using Kraft lignin as the carbon precursor and NaOH as an alternative activation agent instead of the high-cost and high-corrosive KOH for the first time. The structure of carbon particles can be accurately transitioned from a compact to hollow structure, and the surface textural properties can be easily tuned by altering the NaOH concentration. The obtained porous carbon spheres were applied as highly packed thin film electrode materials for supercapacitor devices. The specific capacitance value of porous carbon spheres with a highly compact structure (high packing density) is 66.5 F g-1, which is higher than that of commercial activated carbon and other biomass-derived carbon. This work provides a green processing for producing low-cost and environment-friendly porous carbon spheres from abundant Kraft lignin and important insight for selecting NaOH as an activator to tailor the morphology and structure, which represents an economical and sustainable approach for energy storage devices.
Asunto(s)
Lignina , Electrodos , Porosidad , Hidróxido de SodioRESUMEN
The purpose of this study was to demonstrate the preparation of spherical submicron YAG:Ce particles with controllable particle outer diameters and crystallite sizes and their photoluminescence (PL) properties, which were produced using a flame-assisted spray-pyrolysis method followed by the annealing process. The correlation of particle outer diameter, crystallite size, and PL performance of the prepared particles was also investigated. Experimental results showed that the increases in the particle outer diameters have an impact on the obtainment of higher PL performance. Large particle outer diameters permitted the crystallites to grow more, whereas this is in contrast to the condition for small particle outer diameter having limitations in crystallite growth. This study also found that too large outer diameter (>557 nm) was not effective since crystallites cannot grow anymore and it permits possible scattering problems. This study provides significant information for optimizing synthesis parameters for controlling particle outer diameters and crystallite sizes, which could be relevant to other functional properties, especially for lens, solar cell, and LED applications.