RESUMEN
A previous study showed that the length of the foreskin plays a role in the risk of sexually transmitted infections and chronic prostatitis, which can lead to poor quality of sexual life. Here, the association between foreskin length and sexual dysfunction was evaluated. A total of 5700 participants were recruited from the andrology clinic at The First Affiliated Hospital of University of Science and Technology of China (Hefei, China). Clinical characteristics, including foreskin length, were collected, and sexual function was assessed by the International Index of Erectile Function-5 (IIEF-5) and Premature Ejaculation Diagnostic Tool (PEDT) questionnaires. Men with sexual dysfunction were more likely to have redundant foreskin than men without sexual dysfunction. Among the 2721 erectile dysfunction (ED) patients and 1064 premature ejaculation (PE) patients, 301 (11.1%) ED patients and 135 (12.7%) PE patients had redundant foreskin, respectively. Men in the PE group were more likely to have redundant foreskin than men in the non-PE group (P = 0.004). Logistic regression analyses revealed that the presence of redundant foreskin was associated with increased odds of moderate/severe ED (adjusted odds ratio [aOR] = 1.31, adjusted P = 0.04), moderate PE (aOR = 1.38, adjusted P = 0.02), and probable PE (aOR = 1.37, adjusted P = 0.03) after adjusting for confounding variables. Our study revealed a positive correlation between the presence of redundant foreskin and the risk of sexual dysfunction, especially in PE patients. Assessment of the length of the foreskin during routine clinical diagnosis may provide information for patients with sexual dysfunction.
RESUMEN
Aerogels have been widely studied in the field of thermal insulation. Herein, we reported a kind of conjugated micropolymer (CMP) aerogel synthesized by 1,3,5-triethynylbenzene and 2-amino-3,5-dibromopyridine. To enhance the flame-retardant property, we composited hydroxyapatite (HAP) nanowires with a CMP aerogel. Transmission electron microscopy (TEM) analysis revealed that HAP nanowires were encapsulated within nanosized CMP tubes. In addition, the thermal conductivity of HAP2-NCMP aerogel was 0.0251 W m-1 K-1, which possesses good thermal insulation property. In the micro-combustion calorimeter (MCC) test, compared with pure NCMP, the peak heat release rate (pHRR) of HAP2-NCMP decreased from 39.3 to 30.82 W g-1, approximately 21.6% lower. Furthermore, with the increased addition of hydroxyapatite in the HAP-NCMP composite, the pHRR of HAP3-NCMP decreased by about 37.4%. Besides, NCMP possesses good mechanical properties, with a compressive strength of 117.3 kPa at a strain level of 60%. These findings suggest promising application potential for HAP-NCMP in energy-saving and flame-retardant applications.
RESUMEN
The development and preparation of multifunctional photothermal conversion materials has far-reaching significance for the utilization of solar energy resources in response to the energy crisis. Herein, we propose a Janus membrane for interfacial solar evaporation and phase change energy storage. The membranes were fabricated via combining the PVA film with multi-shelled hollow spheres (MHS). The membranes have asymmetric wettability, that is, one side is hydrophilic and the other side is hydrophobic. The as-resulted membranes obtain outstanding light absorption without further processing. According to these two advantages, the membranes were applied to solar evaporation. The evaporation rate of the membrane is 1.41 kg*m-2h-1 and the evaporation efficiency is 92.4 % under 1sun irradiation. Moreover, the membrane prepared by impregnating 1-Hexadecanamine (HDA) into MHS possesses excellent tensile strength (2.21 MPa) and photothermal conversion ability. The light-to-thermal conversion efficiency can reach 81.9 % under 1sun irradiation. Therefore, the membranes have broad application prospects in the field of photothermal conversion.
RESUMEN
Developing high-efficiency solar photothermal conversion and storage (SPCS) technology is significant in solving the imbalance between the supply and demand of solar energy utilization in time and space. Aiming at the current research status in the field of SPCS, this review thoroughly examines the phase change materials and substrates in SPCS systems. It elucidates the design principles and methods of SPCS integrated composites. Comparatively, it analyzes the parameters of various types of SPCS composites in terms of photothermal conversion, thermal conductivity, energy density, and cycling stability. Additionally, the review discusses the trade-offs between each parameter to achieve the most optimal effect of SPCS. By sorting out the current status of the application of SPCS technology in solar thermal/photovoltaic, aerospace, buildings, textile, and other industries, this analysis clarifies the requirements for various latent heat, phase change temperature, and other properties under different environmental conditions. Through a comprehensive discussion of SPCS technology, this paper accurately captures the development trend of efficiently and comprehensively utilizing solar energy by analyzing existing scientific problems. It identifies bottlenecks in SPCS technology and suggests future development directions that need focused attention. The insights gained from this analysis may provide a theoretical basis for designing strategies, enhancing performance, and promoting the application of SPCS.
RESUMEN
Solar-driven interfacial evaporation (SDIE) stands out as a prospective technology for freshwater production, playing a significant role in mitigating global water scarcity. Herein, a cyclodextrin polymer/chitosan composite aerogel (PPy-La/Al@CDP-CS) with vertically aligned channels was prepared as a solar evaporator for efficient solar steam generation. The vertically aligned pore structure, achieved through directional freezing assisted by liquid nitrogen, not only improves water transport during evaporation but also enhances light absorption through multiple reflections of sunlight within the pores. The polypyrrole particles sprayed on the surface of the aerogel acted as a light-absorbing layer, resulting in an impressive absorbance of 98.15 % under wetting conditions. The aerogel has an evaporation rate of 1.85 kg m-2 h-1 under 1 kW m-2 irradiation. Notably, the vertical pore structure of the aerogel allows it to exhibit excellent evaporation performance and salt resistance even in highly concentrated salt solutions. Furthermore, this aerogel is an excellent solar-driven interfacial evaporator for purifying seawater and fluoride-containing wastewater. This photothermal aerogel has the advantages of excellent performance, low cost, and environmental friendliness, and thus this work provides a new approach to the design and fabrication of solar photothermal materials for water treatment.
