RESUMEN
Hydrogenation of biomass-derived chemicals is of interest for the production of biofuels and valorized chemicals. Thermochemical processes for biomass reduction typically employ hydrogen as the reductant at elevated temperatures and pressures. Here, the authors investigate the direct electrified reduction of 5-hydroxymethylfurfural (HMF) to a precursor to bio-polymers, 2,5-bis(hydroxymethyl)furan (BHMF). Noting a limited current density in prior reports of this transformation, a hybrid catalyst consisting of ternary metal nanodendrites mixed with a cationic ionomer, the latter purposed to increase local pH and facilitate surface proton diffusion, is investigated. This approach, when implemented using Ga-doped Ag-Cu electrocatalysts designed for p-d orbital hybridization, steered selectivity to BHMF, achieving a faradaic efficiency (FE) of 58% at 100 mA cm-2 and a production rate of 1 mmol cm-2 h-1, the latter a doubling in rate compared to the best prior reports.
RESUMEN
The electrochemical reduction of CO2 in acidic conditions enables high single-pass carbon efficiency. However, the competing hydrogen evolution reaction reduces selectivity in the electrochemical reduction of CO2, a reaction in which the formation of CO, and its ensuing coupling, are each essential to achieving multicarbon (C2+) product formation. These two reactions rely on distinct catalyst properties that are difficult to achieve in a single catalyst. Here we report decoupling the CO2-to-C2+ reaction into two steps, CO2-to-CO and CO-to-C2+, by deploying two distinct catalyst layers operating in tandem to achieve the desired transformation. The first catalyst, atomically dispersed cobalt phthalocyanine, reduces CO2 to CO with high selectivity. This process increases local CO availability to enhance the C-C coupling step implemented on the second catalyst layer, which is a Cu nanocatalyst with a Cu-ionomer interface. The optimized tandem electrodes achieve 61% C2H4 Faradaic efficiency and 82% C2+ Faradaic efficiency at 800 mA cm-2 at 25 °C. When optimized for single-pass utilization, the system reaches a single-pass carbon efficiency of 90 ± 3%, simultaneous with 55 ± 3% C2H4 Faradaic efficiency and a total C2+ Faradaic efficiency of 76 ± 2%, at 800 mA cm-2 with a CO2 flow rate of 2 ml min-1.
RESUMEN
Electrocatalytic oxidative dehydrogenation (EOD) of aldehydes enables ultra-low voltage, bipolar H2 production with co-generation of carboxylic acid. Herein, we reported a simple galvanic replacement method to prepare CuM (M = Pt, Pd, Au, and Ag) bimetallic catalysts to improve the EOD of furfural to reach industrially relevant current densities. The redox potential difference between Cu/Cu2+ and a noble metal M/My+ can incorporate the noble metal on the Cu surface and enlarge its surface area. Particularly, dispersing Pt in Cu (CuPt) achieved a record-high current density of 498 mA cm-2 for bipolar H2 production at a low cell voltage of 0.6 V and a Faradaic efficiency of >80% to H2. Future research is needed to deeply understand the synergistic effects of Cu-M toward EOD of furfural, and improve the Cu-M catalyst stability, thus offering great opportunities for future distributed manufacturing of green hydrogen and carbon chemicals with practical rates and low-carbon footprints.
RESUMEN
Here, low-energy poly(ethylene terephthalate) (PET) chemical recycling in water: PET copolymers with diethyl 2,5-dihydroxyterephthalate (DHTE) undergo selective hydrolysis at DHTE sites, autocatalyzed by neighboring group participation, is demonstrated. Liberated oligomeric subchains further hydrolyze until only small molecules remain. Poly(ethylene terephthalate-stat-2,5-dihydroxyterephthalate) copolymers were synthesized via melt polycondensation and then hydrolyzed in 150-200 °C water with 0-1 wt% ZnCl2 , or alternatively in simulated sea water. Degradation progress follows pseudo-first order kinetics. With increasing DHTE loading, the rate constant increases monotonically while the thermal activation barrier decreases. The depolymerization products are ethylene glycol, terephthalic acid, 2,5-dihydroxyterephthalic acid, and bis(2-hydroxyethyl) terephthalate dimer, which could be used to regenerate virgin polymer. Composition-optimized copolymers show a decrease of nearly 50% in the Arrhenius activation energy, suggesting a 6-order reduction in depolymerization time under ambient conditions compared to that of PET homopolymer. This study provides new insight to the design of polymers for end-of-life while maintaining key properties like service temperature and mechanical properties. Moreover, this chemical recycling procedure is more environmentally friendly compared to traditional approaches since water is the only needed material, which is green, sustainable, and cheap.
RESUMEN
Bicarbonate electrolyzer can achieve the direct conversion of CO2 capture solutions that bypasses energy-intensive steps of CO2 regeneration and pressurization. However, only single-carbon chemicals (i. e., CO, formate, CH4 ) were reported as the major products so far. Herein, bicarbonate conversion to multicarbon (C2+ ) products (i. e., acetate, ethylene, ethanol, propanol) was achieved on rationally designed Cu/Ag bilayer electrodes with bilayer cation- and anion-conducting ionomers. The in-situ generated CO2 was first reduced to CO on the Ag layer, followed by its favorable further reduction to C2+ products on the Cu layer, benefiting from the locally high concentration of CO. Through optimizing the bilayer configurations, metal compositions, ionomer types, and local hydrophobicity, a microenvironment was created (high local pH, low water content, etc.) to enhance bicarbonate-to-C2+ conversion and suppress the hydrogen evolution reaction. Subsequently, a maximum C2+ faradaic efficiency of 41.6±0.39 % was achieved at a considerable current density of 100â mA cm-2 .
RESUMEN
Bismuth nanosheets (BiNSs) have been recognized as a promising catalyst for electrochemical CO2 reduction (CO2RR) to formate, but their preparation typically involves an elaborate synthesis of Bi precursors under elevated temperatures and pressures. Here, we demonstrate a simple surfactant-free method of preparing Bi2O3-derived BiNSs (OD-BiNSs) by aqueous precipitation and cyclic voltammetry (CV) under ambient conditions. In situ morphology transformation from Bi2O3 to BiNSs was observed during CV, in which the presence of oxygen and the initial morphology of Bi2O3 are crucial for the phase transformation. The as-prepared OD-BiNSs showed 93% of faradic efficiency (FE) to formate with a partial current density of 62 mA cm-2 at -0.95 VRHE in the H-cell and >94% FE at 50-200 mA cm-2 with cell voltages of 2.4-4.0 V in the flow cell.
RESUMEN
Magnetic field- and polarization-dependent measurements on bright and dark excitons in monolayer WSe2 combined with time-dependent density functional theory calculations reveal intriguing phenomena. Magnetic fields up to 25 T parallel to the WSe2 plane lead to a partial brightening of the energetically lower lying exciton, leading to an increase of the dephasing time. Using a broadband femtosecond pulse excitation, the bright and partially allowed excitonic state can be excited simultaneously, resulting in coherent quantum beating between these states. The magnetic fields perpendicular to the WSe2 plane energetically shift the bright and dark excitons relative to each other, resulting in the hybridization of the states at the K and K' valleys. Our experimental results are well captured by time-dependent density functional theory calculations. These observations show that magnetic fields can be used to control the coherent dephasing and coupling of the optical excitations in atomically thin semiconductors.
