Surface Chemistry of Gold Nanoparticles Produced by Laser Ablation in Pure and Saline Water.

Pulsed laser ablation in liquid (PLAL) is a powerful method for producing nanoparticle colloids with a long-term stability despite the absence of stabilizing organic agents. The colloid stability involves different reactivities and chemical equilibria with complex ionic-specific effects at the nanoparticle/solvent interface which must be strongly influenced by their chemical composition. In this work, the surface composition of PLAL-produced gold nanoparticles in alkaline and saline (NaBr) water is investigated by X-ray photoelectron spectroscopy on free-flying nanoparticles, exempt from any substrate or radiation damage artifact. The Au 4f photoelectron spectra with a depth profiling investigation are used to evaluate the degree of nanoparticle surface oxidation. In alkaline water, the results preclude any surface oxidation contrary to the case of nanoparticles produced in NaBr solution. In addition, the analysis of Br 3d core-level photoelectron spectra agrees with a clear signature of Br on the nanoparticle surface, which is confirmed by a specific valence band feature. This experimental study is supported by DFT calculations, evaluating the energy balance of halide adsorption on different configurations of gold surfaces including oxidation or adsorbed salts.

An electrostatic in-line charge-state purification system for multicharged ions in the kiloelectronvolt energy range.

The performance of a newly built omega type electrostatic analyzer designed to act as an in-line charge-state purification system for ions in the kiloelectronvolt energy range is reported. The analyzer consists of a set of four consecutive electrostatic 140° concentric cylindrical electrodes enclosed by Matsuda electrodes. This setup was recently tested and validated using O5+, Ar9+, and Xe20+ ion beams at an energy of 14 qkeV at the ARIBE facility. A resolving power of 10.5 and a transmission of 100% of the desired charge state are measured allowing a good purification of incoming ion beams with charge states up to 10+ and a fairly good purification for charge states at least up to 20+. In comparison with other in-line solutions such as the Wien filter, our system has the advantage of being purely electrostatic and therefore lacking common drawbacks as, for example, hysteresis.

Assessing the Surface Oxidation State of Free-Standing Gold Nanoparticles Produced by Laser Ablation.

The surface chemistry of gold nanoparticles produced by the pulsed laser ablation in liquids method is investigated by X-ray photoelectron spectroscopy (XPS). The presence of surface oxide expected on these systems is investigated using synchrotron radiation in conditions close to their original state in solvent but free from substrate or solvent effects which could affect the interpretation of spectroscopic observations. For that purpose we performed the experiment on a controlled free-standing nanoparticle beam produced by combination of an atomizer and an aerodynamic lens system. These results are compared with those obtained by the standard situation of deposited nanoparticles on silicon substrate. An accurate analysis based on Bayesian statistics concludes that the existence of oxide in the free-standing conditions cannot be solely confirmed by the recorded core-level 4f spectra. If present, our data indicate an upper limit of 2.15 ± 0.68% of oxide. However, a higher credence to the hypothesis of its existence is brought by the structureless valence profile of the free-standing beam. Moreover, the cross-comparison with the deposited nanoparticles case clearly evidences an important misleading substrate effect. Experiment with free-standing nanoparticles is then demonstrated to be the right way to further investigate oxidation states on Au nanoparticles.

Theoretical analysis for the design of the French watt balance experiment force comparator.

This paper presents a preliminary analysis for designing a force comparator to be used in the French watt balance experiment. The first stage of this experiment consists in a static equilibrium, by means of a mechanical beam balance, between a gravitational force (a weight of an artefact having a known mass submitted to the acceleration due to the gravity) and a vertical electromagnetic force acting on a coil driven by a current subject to the magnetic induction field provided by a permanent magnet. The principle of the force comparison in the French experiment is explained. The general design configuration of the force balance using flexure strips as pivots is discussed and theoretical calculation results based on realistic assumptions of the static and dynamic behaviors of the balance are presented.