Development of a neonate X-ray phantom for 2D imaging applications using single-tone inkjet printing.

PURPOSE: Inkjet printers can be used to fabricate anthropomorphic phantoms by the use of iodine-doped ink. However, challenges persist in implementing this technique. The calibration from grayscale to ink density is complex and time-consuming. The purpose of this work is to develop a printing methodology that requires a simpler calibration and is less dependent on printer characteristics to produce the desired range of x-ray attenuation values. METHODS: Conventional grayscale printing was substituted by single-tone printing; that is, the superposition of pure black layers of iodinated ink. Printing was performed with a consumer-grade inkjet printer using ink made of potassium-iodide (KI) dissolved in water at 1 g/ml. A calibration for the attenuation of ink was measured using a commercial x-ray system at 70 kVp. A neonate radiograph obtained at 70 kVp served as an anatomical model. The attenuation map of the neonate radiograph was processed into a series of single-tone images. Single-tone images were printed, stacked, and imaged at 70 kVp. The phantom was evaluated by comparing attenuation values between the printed phantom and the original radiograph; attenuation maps were compared using the structural similarity index measure (SSIM), while attenuation histograms were compared using the Kullback-Leibler (KL) divergence. A region of interest (ROI)-based analysis was also performed, where the attenuation distribution within given ROIs was compared between phantom and patient. The phantom sharpness was evaluated in terms of modulation transfer function (MTF) estimates and signal spread profiles of high spatial resolution features in the image. RESULTS: The printed phantom required 36 pages. The printing queue was automated and it took about 2 h to print the phantom. The radiograph of the printed phantom demonstrated a close resemblance to the original neonate radiograph. The SSIM of the phantom with respect to that of the patient was 0.53. Both patient and phantom attenuation histograms followed similar distributions, and the KL divergence between such histograms was 0.20. The ROI-based analysis showed that the largest deviations from patient attenuation values were observed at the higher and lower ends of the attenuation range. The limiting resolution of the proposed methodology was about 1 mm. CONCLUSION: A methodology to generate a neonate phantom for 2D imaging applications, using single-tone printing, was developed. This method only requires a single-value calibration and required less than 2 h to print a complete phantom.

Physics-based iterative reconstruction for dual-source and flying focal spot computed tomography.

PURPOSE: For single-source helical Computed Tomography (CT), both Filtered-Back Projection (FBP) and statistical iterative reconstruction have been investigated. However, for dual-source CT with flying focal spot (DS-FFS CT), a statistical iterative reconstruction that accurately models the scanner geometry and acquisition physics remains unknown to researchers. Therefore, our purpose is to present a novel physics-based iterative reconstruction method for DS-FFS CT and assess its image quality. METHODS: Our algorithm uses precise physics models to reconstruct from the native cone-beam geometry and interleaved dual-source helical trajectory of a DS-FFS CT. To do so, we construct a noise physics model to represent data acquisition noise and a prior image model to represent image noise and texture. In addition, we design forward system models to compute the locations of deflected focal spots, the dimension, and sensitivity of voxels and detector units, as well as the length of intersection between x-rays and voxels. The forward system models further represent the coordinated movement between the dual sources by computing their x-ray coverage gaps and overlaps at an arbitrary helical pitch. With the above models, we reconstruct images by an advanced Consensus Equilibrium (CE) numerical method to compute the maximum a posteriori estimate to a joint optimization problem that simultaneously fits all models. RESULTS: We compared our reconstruction with Siemens ADMIRE, which is the clinical standard hybrid iterative reconstruction (IR) method for DS-FFS CT, in terms of spatial resolution, noise profile, and image artifacts through both phantoms and clinical scan datasets. Experiments show that our reconstruction has a higher spatial resolution, with a Task-Based Modulation Transfer Function (MTFtask ) consistently higher than the clinical standard hybrid IR. In addition, our reconstruction shows a reduced magnitude of image undersampling artifacts than the clinical standard. CONCLUSIONS: By modeling a precise geometry and avoiding data rebinning or interpolation, our physics-based reconstruction achieves a higher spatial resolution and fewer image artifacts with smaller magnitude than the clinical standard hybrid IR.

Flat Panel Detector c-Arms Are Associated with Dramatically Reduced Radiation Exposure During Ureteroscopy and Produce Superior Images.

Background: We wished to determine whether newly available flat panel detector (FPD) c-arms were (1) associated with lower radiation dose during ureteroscopy (URS) than conventional image intensifier (CII) c-arms and (2) to compare fluoroscopic image quality between the units. Materials and Methods: We retrospectively reviewed 44 consecutive patients undergoing URS at a pediatric hospital, with c-arms assigned by availability in the operating room. We performed dosimetry experiments using the same c-arms on standard phantoms. Results: Patient and case characteristics did not differ significantly between the two groups of patients. The median dose in the FPD group was less than a quarter of the dose in the CII group, 0.48 [0.42, 0.97] mGy vs 2.2 [1.1, 3.8] mGy, p < 0.0001. The FPD dose remained at less than one-third of the CII dose accounting for any difference in fluoroscopy time, and remained significant in a multivariate model including fluoroscopy time and patient weight (ß = 2.4, p = 0.007). Phantom studies showed higher image quality for FPDs at all simulated patient sizes, even at lower radiation doses. Conclusions: This is the first report comparing radiation dose from c-arms of image intensifiers and FPDs in adults or children. Use of an FPD during URS was associated with a substantially decreased absorbed dose for patients while simultaneously improving image quality.

Development of a novel framework to evaluate the localization accuracy of tomosynthesis-guided breast biopsy units.

PURPOSE: To develop a scheme to quantitatively assess localization accuracy of tomosynthesis-guided vacuum-assisted breast biopsy apparatus. METHODS: A phantom containing a metallic pellet on a flexible plastic shaft was constructed and was tested in cranio-caudal (CC) and lateral (LAT) arm biopsy geometries following the standard clinical breast biopsy workflow. Three points were manually digitized on tomosynthesis images including: the center of the target, and the tip of the needle in pre- and postfire positions. The needle trajectory was determined and four error metrics were defined: (1) stroke length error (difference between the nominal and measured stroke lengths); (2) Euclidian distance between the target and center of trough (i.e., aperture); (3) longitudinal distance between target and center of trough; and (4) lateral distance between target and needle. The proposed methodology was also evaluated on a breast gel phantom and the complete biopsy procedure, including vacuum-assisted biopsy was performed. RESULTS: Three biopsy geometries were investigated: (i) LAT arm on a prone table unit (Hologic, Affirm Prone), (ii) CC- and (iii) LAT arm in an upright unit (Hologic Affirm Upright). Both biopsy units passed the vendor-provided daily localization accuracy test, with <1 mm nominal error in each dimension. The aforementioned error metrics (1) to (4) were (0.6, 1.8, 0.4, 1.7) mm, (0.4, 4.2, 4.1, 1.1) mm, and (0.3, 2.4, 0.7, 2.3) mm, respectively, for geometry-I, -II, and -III. The gel phantom was tested on the upright unit with lateral arm and the error metrics (1) to (4) were 0.4, 2.5, 0.8, and 2.4 mm respectively. CONCLUSIONS: A framework was developed to evaluate the tomosynthesis-guided breast biopsy localization error, allowing quantitative comparisons between different systems and biopsy configurations. The proposed framework can also be extended to the stereotactic breast biopsy units. We suggest that a quantitative tolerance level for localization accuracy of breast biopsy units be established.

Intraoperative Use of O-arm in Pediatric Cervical Spine Surgery.

INTRODUCTION: Traditionally, fluoroscopy and postoperative computed tomographic (CT) scans are used to evaluate screw position after pediatric cervical spine fusion. However, noncontained screws detected postoperatively can require revision surgery. Intraoperative O-arm is a 3-dimensional CT imaging technique, which allows intraoperative evaluation of screw position and potentially avoids reoperations because of implant malposition. This study's objective was to evaluate the use of intraoperative O-arm in determining the accuracy of cervical implants placed by a free-hand technique using anatomic landmarks or fluoroscopic guidance in pediatric cervical spine instrumentation. METHODS: A single-center retrospective study of consecutive examinations of children treated with cervical spine instrumentation and intraoperative O-arm from 2014 to 2018 was performed. In total, 44 cases (41 children, 44% men) with a mean age of 11.9 years (range, 2.1 to 23.5 y) were identified. Instability (n=16, 36%) and deformity (n=10, 23%) were the most frequent indications. Primary outcomes were screw revision rate, neurovascular complications caused by noncontained screws, and radiation exposure. RESULTS: A total of 272 screws were inserted (60 occipital and 212 cervical screws). All screws were evaluated on fluoroscopy as appropriately placed. Four screws (1.5%) in 4 cases (9%) were noncontained on O-arm imaging and required intraoperative revision. A mean of 7.7 levels (range, 5 to 13) were scanned. The mean CT dose index and dose-length product were 15.2±6.87 mGy and 212.3±120.48 mGy×cm. Mean effective dose was 1.57±0.818 mSv. There was no association between screw location and noncontainment (P=0.129). No vertebral artery injuries, dural injuries, or neurologic deficits were related to the 4 revised screws. CONCLUSIONS: Intraoperative non-navigated O-arm is a safe and efficient method to evaluate screw position in pediatric patients undergoing cervical spine instrumentation. Noncontained screws were detected in 9% of cases (n=4). O-arm delivers low radiation doses, allows for intraoperative screw revision, and negates the need for postoperative CT scans after confirmation of optimal implant position. LEVEL OF EVIDENCE: Level IV.

Improving Low-Dose Pediatric Abdominal CT by Using Convolutional Neural Networks.

PURPOSE: To evaluate the efficacy of convolutional neural networks (CNNs) to improve the image quality of low-dose pediatric abdominal CT images. MATERIALS AND METHODS: Images from 11 pediatric abdominal CT examinations acquired between June and July 2018 were reconstructed with filtered back projection (FBP) and an iterative reconstruction (IR) algorithm. A residual CNN was trained using the FBP image as the input and the difference between FBP and IR as the target such that the network was able to predict the residual image and simulate the IR. CNN-based postprocessing was applied to 20 low-dose pediatric image datasets acquired between December 2016 and December 2017 on a scanner limited to reconstructing FBP images. The FBP and CNN images were evaluated based on objective image noise and subjective image review by two pediatric radiologists. For each of five features, readers rated images on a five-point Likert scale and also indicated their preferred series. Readers also indicated their "overall preference" for CNN versus FBP. Preference and Likert scores were analyzed for individual and combined readers. Interreader agreement was assessed. RESULTS: The CT number remained unchanged between FBP and CNN images. Image noise was reduced by 31% for CNN images (P < .001). CNN was preferred for overall image quality for individual and combined readers. For combined Likert scores, at least one of the two score types (Likert or binary preference) indicated a significant favoring of CNN over FBP for low contrast, image noise, artifacts, and high contrast, whereas the reverse was true for spatial resolution. CONCLUSION: FBP images can be improved in image space by a well-trained CNN, which may afford a reduction in dose or improvement in image quality on scanners limited to FBP reconstruction.© RSNA, 2019.

Current state of practice regarding digital radiography exposure indicators and deviation indices: Report of AAPM Imaging Physics Committee Task Group 232.

Beginning with the advent of digital radiography systems in 1981, manufacturers of these systems provided indicators of detector exposure. These indicators were manufacturer-specific, and users in facilities with equipment from multiple manufacturers found it a challenge to monitor and manage variations in indicated exposure in routine clinical use. In 2008, a common definition of exposure index (EI) was realized in International Electrotechnical Commission (IEC) International Standard 62494-1 Ed. 1, which also introduced and defined the deviation index (DI), a number quantifying the difference between the detector EI for a given radiograph and the target exposure index (EIT ). An exposure index that differed by a constant from that established by the IEC and the concept of the deviation index also appear in American Association of Physicists in Medicine (AAPM) Report No. 116 published in 2009. The AAPM Report No. 116 went beyond the IEC standard in supplying a table (Table II in the report of TG-116) titled "Exposure Indicator DI Control Limits for Clinical Images," which listed suggested DI ranges and actions to be considered for each range. As the IEC EI was implemented and clinical DI data were gathered, concerns were voiced that the DI control limits published in the report of TG-116 were too strict and did not accurately reflect clinical practice. The charge of task group 232 (TG-232) and the objective of this final report was to investigate the current state of the practice for CR/DR Exposure and Deviation Indices based on AAPM TG 116 and IEC-62494, for the purpose of establishing achievable goals (reference levels) and action levels in digital radiography. Data corresponding to EI and DI were collected from a range of practice settings for a number of body parts and views (adults and pediatric radiographs) and analyzed in aggregate and separately. A subset of radiographs was also evaluated by radiologists based on criteria adapted from the European Guidelines on Quality Criteria for Diagnostic Radiographic Images from the European Commission. Analysis revealed that typical DI distribution was characterized by a standard deviation (SD) of 1.3-3.6 with mean DI values substantially different from 0.0, and less than 50% of DI values fell within the significant action limits proposed by AAPM TG-116 (-1.0 ≤ DI ≤ 1.0). Recommendations stemming from this analysis include targeting a mean DI value of 0.0 and action limits at ±1 and ±2 SD of the DI based on actual DI data of an individual site. EIT values, DI values, and associated action limits should be reviewed on an ongoing basis and optimization of DI values should be a process of continuous quality improvement with a goal of reducing practice variation.

The effect of surgeon versus technologist control of fluoroscopy on radiation exposure during pediatric ureteroscopy: A randomized trial.

BACKGROUND: Fluoroscopy is commonly used during pediatric ureteroscopy (PURS) for urolithiasis, and the most important contributor to overall radiation exposure is fluoroscopy time (FT). One factor that may impact FT is who controls activation of the fluoroscope: the urologist (with a foot pedal) or the radiation technologist (as directed by the urologist). While there are plausible reasons to believe that either approach may lead to reduced FT, there are no systematic investigations of this question. We sought to compare FT with surgeon-control versus technologist control during PURS for urolithiasis. METHODS: We conducted a randomized controlled trial (Clinicaltrials.gov ID number: NCT02224287). Institutional Review Board approval was sought and obtained for this study. All subjects (or their legal guardians) provided informed consent. Each patient (age 5-26 years) was randomized to surgeon- or technologist-controlled fluoroscope activation. Block randomization was stratified by the surgeon. For technologist control, the surgeon verbally directed the technologist to activate the fluoroscope. For surgeon control, a foot pedal was used by the surgeon. The technologist controlled c-arm positioning, settings, and movement. The primary outcome was total FT for the procedure. Secondary outcomes included radiation exposure (entrance surface air kerma [ESAK] mGy). We also analyzed clinical and procedural predictors of FT and exposure. Mixed linear models accounting for clustering by surgeon were developed. RESULTS: Seventy-three procedures (5 surgeons) were included. The number of procedures per surgeon ranged from seven to 36. Forty-three percent were pre-stented. Thirty-one procedures were left side, 35 were right side, and seven were bilateral. Stones were treated in 71% of procedures (21% laser, 14% basket, and 65% laser/basket). Stone locations were distal ureter (11.5%), proximal/mid-ureter (8%), renal (69%), and ureteral/renal (11.5%). An access sheath was used in 77%. Median stone size was 8.0 mm (range 2.0-20.0). Median FT in the surgeon control group was 0.5 min (range 0.01-6.10) versus 0.55 min (range 0.10-5.50) in the technologist-control group (p = 0.284). Median ESAK in the surgeon control group was 46.02 mGy (range 5.44-3236.80) versus 46.99 mGy (range: 0.17-1039.31) in the technologist-control group (p = 0.362). Other factors associated with lower FT on univariate analysis included female sex (p = 0.015), no prior urologic surgeries (p = 0.041), shorter surgery (p = 0.011), and no access sheath (p = 0.006). On multivariable analysis only female sex (p = 0.017) and no access sheath (p = 0.049) remained significant. There was significant variation among surgeons (p < 0.0001); individual surgeon median FT ranged from 0.40 to 2.95 min. CONCLUSIONS: Fluoroscopy time and radiation exposure are similar whether the surgeon or technologist controls fluoroscope activation. Other strategies to reduce exposure might focus on surgeon-specific factors, given the significant variation between surgeons.

Correction to: Ionizing radiation from computed tomography versus anesthesia for magnetic resonance imaging in infants and children: patient safety considerations.

The published version of this article incorrectly lists Dr. Joseph P. Cravero in the Department of Radiology at Boston Children's Hospital. Dr. Cravero's correct affiliation is given below.

Ionizing radiation from computed tomography versus anesthesia for magnetic resonance imaging in infants and children: patient safety considerations.

In the context of health care, risk assessment is the identification, evaluation and estimation of risk related to a particular clinical situation or intervention compared to accepted medical practice standards. The goal of risk assessment is to determine an acceptable level of risk for a given clinical treatment or intervention in association with the provided clinical circumstances for a patient or group of patients. In spite of the inherent challenges related to risk assessment in pediatric cross-sectional imaging, the potential risks of ionizing radiation and sedation/anesthesia in the pediatric population are thought to be quite small. Nevertheless both issues continue to be topics of discussion concerning risk and generate significant anxiety and concern for patients, parents and practicing pediatricians. Recent advances in CT technology allow for more rapid imaging with substantially lower radiation exposures, obviating the need for anesthesia for many indications and potentially mitigating concerns related to radiation exposure. In this review, we compare and contrast the potential risks of CT without anesthesia against the potential risks of MRI with anesthesia, and discuss the implications of this analysis on exam selection, providing specific examples related to neuroblastoma surveillance imaging.

Development of a tool to aid the radiologic technologist using augmented reality and computer vision.

This technical innovation describes the development of a novel device to aid technologists in reducing exposure variation and repeat imaging in computed and digital radiography. The device consists of a color video and depth camera in combination with proprietary software and user interface. A monitor in the x-ray control room displays the position of the patient in real time with respect to automatic exposure control chambers and image receptor area. The thickness of the body part of interest is automatically displayed along with a motion indicator for the examined body part. The aim is to provide an automatic measurement of patient thickness to set the x-ray technique and to assist the technologist in detecting errors in positioning and motion before the patient is exposed. The device has the potential to reduce the incidence of repeat imaging by addressing problems technologists encounter daily during the acquisition of radiographs.

How we read pediatric PET/CT: indications and strategies for image acquisition, interpretation and reporting.

PET/CT plays an important role in the diagnosis, staging and management of many pediatric malignancies. The techniques for performing PET/CT examinations in children have evolved, with increasing attention focused on reducing patient exposure to ionizing radiation dose whenever possible and minimizing scan duration and sedation times, with a goal toward optimizing the overall patient experience. This review outlines our approach to performing PET/CT, including a discussion of the indications for a PET/CT exam, approaches for optimizing the exam protocol, and a review of different approaches for acquiring the CT portion of the PET/CT exam. Strategies for PACS integration, image display, interpretation and reporting are also provided. Most practices will develop a strategy for performing PET/CT that best meets their respective needs. The purpose of this article is to provide a comprehensive overview for radiologists who are new to pediatric PET/CT, and also to provide experienced PET/CT practitioners with an update on state-of-the art CT techniques that we have incorporated into our protocols and that have enabled us to make considerable improvements to our PET/CT practice.

Operational and Dosimetric Aspects of Pediatric PET/CT.

No consistent guidelines exist for the acquisition of a CT scan as part of pediatric PET/CT. Given that children may be more vulnerable to the effects of ionizing radiation, it is necessary to develop methods that provide diagnostic-quality imaging when needed, in the shortest time and with the lowest patient radiation exposure. This article describes the basics of CT dosimetry and PET/CT acquisition in children. We describe the variability in pediatric PET/CT techniques, based on a survey of 19 PET/CT pediatric institutions in North America. The results of the survey demonstrated that, although most institutions used automatic tube current modulation, there remained a large variation of practice, on the order of a factor of 2-3, across sites, pointing to the need for guidelines. We introduce the approach developed at our institution for using a multiseries PET/CT acquisition technique that combines diagnostic-quality CT in the essential portion of the field of view and a low-dose technique to image the remainder of the body. This approach leads to a reduction in radiation dose to the patient while combining the PET and the diagnostic CT into a single acquisition. The standardization of pediatric PET/CT provides an opportunity for a reduction in the radiation dose to these patients while maintaining an appropriate level of diagnostic image quality.

Quality of pediatric abdominal CT scans performed at a dedicated children's hospital and its referring institutions: a multifactorial evaluation.

BACKGROUND: Pediatric patients requiring transfer to a dedicated children's hospital from an outside institution may undergo CT imaging as part of their evaluation. Whether this imaging is performed prior to or after transfer has been shown to impact the radiation dose imparted to the patient. Other quality variables could also be affected by the pediatric experience and expertise of the scanning institution. OBJECTIVE: To identify differences in quality between abdominal CT scans and reports performed at a dedicated children's hospital, and those performed at referring institutions. MATERIALS AND METHODS: Fifty consecutive pediatric abdominal CT scans performed at outside institutions were matched (for age, gender and indication) with 50 CT scans performed at a dedicated freestanding children's hospital. We analyzed the scans for technical parameters, report findings, correlation with final clinical diagnosis, and clinical utility. Technical evaluation included use of intravenous and oral contrast agents, anatomical coverage, number of scan phases and size-specific dose estimate (SSDE) for each scan. Outside institution scans were re-reported when the child was admitted to the children's hospital; they were also re-interpreted for this study by children's hospital radiologists who were provided with only the referral information given in the outside institution's report. Anonymized original outside institutional reports and children's hospital admission re-reports were analyzed by two emergency medicine physicians for ease of understanding, degree to which the clinical question was answered, and level of confidence in the report. RESULTS: Mean SSDE was lower (8.68) for children's hospital scans, as compared to outside institution scans (13.29, P = 0.03). Concordance with final clinical diagnosis was significantly lower for original outside institution reports (38/48, 79%) than for both the admission and study children's hospital reports (48/50, 96%; P = 0.005). Children's hospital admission reports were rated higher than outside institution reports for completeness, ease of understanding, answering of clinical question, and level of confidence of the report (P < 0.001). CONCLUSION: Pediatric abdominal CT scans performed and interpreted at a dedicated children's hospital are associated with higher technical quality, lower radiation dose and a more clinically useful report than those performed at referring institutions.

Neuroimaging of Children With Surgically Treated Hydrocephalus: A Practical Approach.

OBJECTIVE: Children with surgically treated hydrocephalus commonly undergo multiple neuroimaging studies. The purpose of this article is to share an experience with use of the as low as reasonably achievable (ALARA) principle to guide the imaging approach to these patients. CONCLUSION: A reasonably achievable strategy for minimizing ionizing radiation in patients with surgically treated hydrocephalus includes rapid-sequence MRI and judicious use of dose-optimized head CT. Rapid-sequence MRI is particularly useful in the care of patients who have undergone endoscopic third ventriculostomy.

Selecting appropriate gastroenteric contrast media for diagnostic fluoroscopic imaging in infants and children: a practical approach.

In our experience, questions about the appropriate use of enteric contrast media for pediatric fluoroscopic studies are common. The purpose of this article is to provide a comprehensive review of enteric contrast media used for pediatric fluoroscopy, highlighting the routine use of these media at a large tertiary care pediatric teaching hospital.

Pediatric thoracic CT angiography at 70 kV: a phantom study to investigate the effects on image quality and radiation dose.

BACKGROUND: Studies have demonstrated that 70-kilovolt (kV) imaging enhances the contrast of iodine, potentially affording a reduction in radiation dose while maintaining the contrast-to-noise ratio (CNR). There is a maximum amount of image noise beyond which increased contrast does not improve structure visualization. Thus, noise should be constrained during protocol optimization. OBJECTIVE: This phantom study investigated the effect of 70-kV imaging for pediatric thoracic CT angiography on image quality and radiation dose in a pediatric population when a noise constraint was considered. MATERIALS AND METHODS: We measured contrast and noise using anthropomorphic thoracic phantoms ranging in size from newborn age equivalent to 10-year-old age equivalent. We inserted contrast rods into the phantoms to simulate injected contrast material used in a CT angiography study. The image-quality metric "iodine CNR with a noise constraint" was used to determine the relative dose factor for each phantom size, kV setting (70-140 kV) and noise constraint (1.00-1.20). A noise constraint of 1.20 indicates that noise should not increase by more than 20% of the noise level in images performed at the reference kV, selected to be 80 kV in this study. The relative dose factor can be applied to the original dose obtained at 80 kV in order to maintain iodine CNR with the noise constraint. A relative dose factor <1.0 indicates potential for dose reduction while a relative dose factor >1.0 indicates a dose penalty. RESULTS: Iodine contrast was highest for 70 kV and decreased with higher kV settings for all phantom sizes. The relative dose factor at 70 kV was <1.0 for all noise constraint >1.0, indicating potential for dose reduction, for the newborn, 1-year-old and 5-year-old age-equivalent phantom sizes. For the 10-year-old age-equivalent phantom, relative dose factor at 70 kV=1.22, 1.11, 1.01, 0.92 and 0.83 for noise constraint=1.00, 1.05, 1.10, 1.15, 1.20, respectively, indicating a dose penalty for noise constraint ≤1.10 and potential for dose reduction for noise constraint >1.10. CONCLUSION: Using 70 kV does allow for radiation dose reduction if the radiologist is willing to accept a higher level of image noise as a trade-off for increased vessel contrast. This increase in noise is small (<5%) for the nominal newborn, 1- and 5-year-old but is >10% for the 10-year-old. Therefore, we recommend limiting 70 kV thoracic CT angiography to newborn through 5-year-old patients.

Sinus Computed Tomography Imaging in Pediatric Cystic Fibrosis: Added Value?

STUDY OBJECTIVE: To evaluate the prevalence of computed tomography (CT) sinus imaging in a pediatric cystic fibrosis (CF) population, determine changes in Lund Mackay (LM) scores over time, and estimate radiation exposure. STUDY DESIGN: Case series with chart review. SETTING: Tertiary care children's hospital. SUBJECTS AND METHODS: In total, 202 pediatric patients with CF who underwent endoscopic sinus surgery (ESS) were included. The total number of CT scans was calculated for each patient, with specific focus on the indications for and subsequent outcomes of the sinus CT scan subgroup. RESULTS: Patients underwent a total of 1718 CT scans, 832 of which were sinus CT scans (mean of 4.2 sinus scans per patient). Disease evaluation (54%) and preoperative planning (35%) were the most common indications. Otolaryngologists were more likely to order imaging for preoperative evaluation, and those scans were more likely to result in surgery compared with those requested by other physicians (P < .001). Ninety CT scans (10.8%) led to no change in management. There was no significant difference in LM scores between patients admitted to the hospital or prescribed antibiotics and those who were not. There was also no significant change in LM score following ESS after adjusting for age and sex (P = .23). CONCLUSION: Based on LM scores, all sinus CT scans in patients with CF reveal moderate to severe sinus disease. Effort should be made to minimize radiation exposure in patients with CF by limiting sinus CT scans to the preoperative context or for evaluation of potential sinusitis complications.

Size-based protocol optimization using automatic tube current modulation and automatic kV selection in computed tomography.

Size-based diagnostic reference ranges (DRRs) for contrast-enhanced pediatric abdominal computed tomography (CT) have been published in order to establish practical upper and lower limits of CTDI, DLP, and SSDE. Based on these DRRs, guidelines for establishing size-based SSDE target levels from the SSDE of a standard adult by applying a linear correction factor have been published and provide a great reference for dose optimization initiatives. The necessary step of designing manufacturer-specific CT protocols to achieve established SSDE targets is the responsibility of the Qualified Medical Physicist. The task is straightforward if fixed-mA protocols are used, however, more difficult when automatic exposure control (AEC) and automatic kV selection are considered. In such cases, the physicist must deduce the operation of AEC algorithms from technical documentation or through testing, using a wide range of phantom sizes. Our study presents the results of such testing using anthropomorphic phantoms ranging in size from the newborn to the obese adult. The effect of each user-controlled parameter was modeled for a single-manufacturer AEC algorithm (Siemens CARE Dose4D) and automatic kV selection algorithm (Siemens CARE kV). Based on the results presented in this study, a process for designing mA-modulated, pediatric abdominal CT protocols that achieve user-defined SSDE and kV targets is described.