Synthesis and Characterisation of Core-Shell Microparticles Formed by Ni-Mn-Co Oxides.

In this work, core and core-shell microparticles formed by Ni-Mn-Co oxides with controlled composition were fabricated by an oxalate-assisted co-precipitation route, and their properties were analysed by diverse microscopy and spectroscopy techniques. The microparticles exhibit dimensions within the 2-6 µm range and mainly consist of NiO and NiMn2O4, the latter being promoted as the temperature of the treatment increases, especially in the shell region of the microparticles. Aspects such as the shell dimensions, the vibrational modes of the spinel compounds primarily observed in the shell region, the oxidation states of the cations at the surface of the microparticles, and the achievement of a Ni-rich 811 core and a Mn-rich 631 shell were thoroughly evaluated and discussed in this work.

Thermoelectric Performance of Hybrid Inorganic/Organic Composites Based on PEDOT:PSS/Tin(II) Oxide.

PEDOT: PSS(poly(3,4-ethylenedioxylthiophene):poly(styrenesulfonate))-based composites often exhibit remarkable characteristics regarding high electrical conductivity and great processability, being a suitable candidate for thermoelectric (TE) applications. To increase its performance, PEDOT:PSS is commonly blended with scarce and toxic inorganic compounds based on Se, Te or Bi. In this work we propose the use of one p-type metal oxide semiconductor (MOs): tin(II) oxide (SnO), motivated by its abundance and low toxicity. Hybrid PEDOT:PSS/SnO composites were obtained by firstly blending Ethylene glycol (EG) with PEDOT:PSS and then by adding p-type SnO, previously synthesized by a chemical route. The mixture was deposited via spin-coating onto glass substrates. The Power Factor (PF) of the composites increased by a factor of 300 with the combined EG/SnO composition.

In Situ Local Oxidation of SnO Induced by Laser Irradiation: A Stability Study.

In this work, semiconductor tin oxide (II) (SnO) nanoparticles and plates were synthesized at room conditions via a hydrolysis procedure. X-ray diffraction (XRD) and transmission electron microscopy (TEM) confirmed the high crystallinity of the as-synthesized romarchite SnO nanoparticles with dimensions ranging from 5 to 16 nm. The stability of the initial SnO and the controlled oxidation to SnO2 was studied based on either thermal treatments or controlled laser irradiation using a UV and a red laser in a confocal microscope. Thermal treatments induced the oxidation from SnO to SnO2 without formation of intermediate SnOx, as confirmed by thermodiffraction measurements, while by using UV or red laser irradiation the transition from SnO to SnO2 was controlled, assisted by formation of intermediate Sn3O4, as confirmed by Raman spectroscopy. Photoluminescence and Raman spectroscopy as a function of the laser excitation source, the laser power density, and the irradiation duration were analyzed in order to gain insights in the formation of SnO2 from SnO. Finally, a tailored spatial SnO/SnO2 micropatterning was achieved by controlled laser irradiation with potential applicability in optoelectronics and sensing devices.

Towards Control of the Size, Composition and Surface Area of NiO Nanostructures by Sn Doping.

Achieving nanostructures with high surface area is one of the most challenging tasks as this metric usually plays a key role in technological applications, such as energy storage, gas sensing or photocatalysis, fields in which NiO is gaining increasing attention recently. Furthermore, the advent of modern NiO-based devices can take advantage of a deeper knowledge of the doping process in NiO, and the fabrication of p-n heterojunctions. By controlling experimental conditions such as dopant concentration, reaction time, temperature or pH, NiO morphology and doping mechanisms can be modulated. In this work, undoped and Sn doped nanoparticles and NiO/SnO2 nanostructures with high surface areas were obtained as a result of Sn incorporation. We demonstrate that Sn incorporation leads to the formation of nanosticks morphology, not previously observed for undoped NiO, promoting p-n heterostructures. Consequently, a surface area value around 340 m2/g was obtained for NiO nanoparticles with 4.7 at.% of Sn, which is nearly nine times higher than that of undoped NiO. The presence of Sn with different oxidation states and variable Ni3+/Ni2+ ratio as a function of the Sn content were also verified by XPS, suggesting a combination of two charge compensation mechanisms (electronic and ionic) for the substitution of Ni2+ by Sn4+. These results make Sn doped NiO nanostructures a potential candidate for a high number of technological applications, in which implementations can be achieved in the form of NiO-SnO2 p-n heterostructures.

Comparative study of the implementation of tin and titanium oxide nanoparticles as electrodes materials in Li-ion batteries.

Transition metal oxides potentially present higher specific capacities than the current anodes based on carbon, providing an increasing energy density as compared to commercial Li-ion batteries. However, many parameters could influence the performance of the batteries, which depend on the processing of the electrode materials leading to different surface properties, sizes or crystalline phases. In this work a comparative study of tin and titanium oxide nanoparticles synthesized by different methods, undoped or Li doped, used as single components or in mixed ratio, or alternatively forming a composite with graphene oxide have been tested demonstrating an enhancement in capacity with Li doping and better cyclability for mixed phases and composite anodes.

Synergetic Improvement of Stability and Conductivity of Hybrid Composites formed by PEDOT:PSS and SnO Nanoparticles.

In this work, layered hybrid composites formed by tin oxide (SnO) nanoparticles synthesized by hydrolysis and poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) have been analyzed. Prior to the composite study, both SnO and PEDOT:PSS counterparts were characterized by diverse techniques, such as X-ray diffraction (XRD), Raman spectroscopy, transmission electron microscopy (TEM), photoluminescence (PL), atomic force microscopy (AFM), optical absorption and Hall effect measurements. Special attention was given to the study of the stability of the polymer under laser illumination, as well as the analysis of the SnO to SnO2 oxidation assisted by laser irradiation, for which different laser sources and neutral filters were employed. Synergetic effects were observed in the hybrid composite, as the addition of SnO nanoparticles improves the stability and electrical conductivity of the polymer, while the polymeric matrix in which the nanoparticles are embedded hinders formation of SnO2. Finally, the Si passivation behavior of the hybrid composites was studied.

Understanding the effects of Cr doping in rutile TiO2 by DFT calculations and X-ray spectroscopy.

The effects of Cr on local environment and electronic structure of rutile TiO2 are studied combining theoretical and experimental approaches. Neutral and negatively charged substitutional Cr impurities CrTi0 and CrTi1- as well as Cr-oxygen vacancy complex 2CrTi + VO are studied by the density functional theory (DFT) within the generalized gradient approximation (GGA) of Perdew-Burke-Ernzerhof (PBE) functional. Experimental results based on X-Ray absorption spectroscopy (XAS) and X-Ray photoelectron spectroscopy (XPS) performed on Cr doped TiO2 at the Synchrotron facility were compared to the theoretical results. It is shown that the electrons of the oxygen vacancy tend to be localized at the t2g states of the Cr ions in order to reach the stable oxidation state of Cr3+. Effects of Cr on crystal field (CF) and structural distortions in the rutile TiO2 cell were analyzed by the DFT calculations and XAS spectra revealing that the CF and tetragonal distortions in TiO2 are very sensitive to the concentration of Cr.