RESUMEN
Water pollution is nowadays a global problem and the effective detection of pollutants is of fundamental importance. Herein, a facile, efficient, robust, and rapid (response time < 2 min) method for the determination of important quinone-based industrial pollutants such as hydroquinone and benzoquinone is reported. The recognition method is based on the use of screen-printed electrodes as sensing platforms, enhanced with carbon-based nanomaterials. The enhancement is achieved by modifying the working electrode of such platforms through highly sensitive membranes made of Single- or Multi-Walled Carbon Nanotubes (SWNTs and MWNTs) or by graphene nanoplatelets. The modified sensing platforms are first carefully morphologically and electrochemically characterized, whereupon they are tested in the detection of different pollutants (i.e., hydroquinone and benzoquinone) in water solution, by using both cyclic and square-wave voltammetry. In particular, the sensors based on film-deposited nanomaterials show good sensitivity with a limit of detection in the nanomolar range (0.04 and 0.07 µM for SWNT- and MWNT-modified SPEs, respectively) and a linear working range of 10 to 1000 ppb under optimal conditions. The results highlight the improved performance of these novel sensing platforms and the large-scale applicability of this method for other analytes (i.e., toxins, pollutants).
RESUMEN
We propose an original technique for the fabrication of terahertz (THz) metasurfaces comprising a 3D printed regular array of polymer hemispheres covered with a thin conductive layer. We demonstrate that the deposition of a thin metal layer onto polymer hemispheres suppresses the THz reflectivity to almost zero, while the frequency range of such a suppression can be considerably broadened by enhancing the structure with graphene. Scaling up of the proposed technique makes it possible to tailor the electromagnetic responses of metasurfaces and allows for the fabrication of various components of THz photonics.
RESUMEN
Composite materials with 83 wt.% of the 0.7Pb(Mg1/3Nb2/3)O3-0.3PbTiO3 distributed in phosphate-bonded ceramics were prepared at three different pressures. A phosphate matrix comprises a mixture of an aluminum phosphate binder and melted periclase, MgO. All samples demonstrate a homogeneous distribution of the ferroelectric perovskite phase and are thermally stable up to 900 K. At higher temperatures, the pyrochlore cubic phase forms. It has been found that the density of the composites non-monotonously depends on the pressure. The dielectric permittivity and losses substantially increase with the density of the samples. The fabricated composites demonstrate diffused ferroelectric-paraelectric transition and prominent piezoelectric properties.
RESUMEN
The patterning of arrays of aligned multi-walled carbon nanotubes (MWCNTs) allows creating metastructures for terahertz (THz) applications. Here, the strips and columns from MWCNTs vertically grown on silicon substrates are prepared using CO2 laser treatment. The tops of the patterned arrays are flat when the laser power is between 15 and 22 W, and craters appear there with increasing power. Laser treatment does not destroy the alignment of MWCNTs while removing their poorly ordered external layers. The products of oxidative destruction of these layers deposit on the surfaces of newly produced arrays. The oxygen groups resulting from the CO2 laser treatment improve the wettability of nanotube arrays with an epoxy resin. We show that the patterned MWCNT arrays absorb the THz radiation more strongly than the as-synthesized arrays. Moreover, the pattern influences the frequency behavior of the absorbance.
RESUMEN
The composites and thin films comprising individual single-walled carbon nanotubes with a polymer coating (p-CNTs) have been prepared and their electromagnetic responses have been studied in a wide range from low-frequency (25-107 Hz) up to the infrared region. In spite of the high volume fraction of the nanotubes (up to 3.3%), the polymer coating prevents direct p-CNT contacts and the formation of the percolation network in those composites, so that p-CNTs interact only via the electromagnetic coupling. Thereby it is an ideal model system to verify experimentally the fundamental issues related to carbon nanotube electromagnetics, such as the influence of inter-tube electron tunneling on the localized plasmon resonance in the terahertz range, or the infrared absorption enhancement of polymer molecules attached to the nanotube surface. Along with addressing the fundamentals, applied carbon nanotube electromagnetics got insights important for the applications of p-CNT based composites as dielectric media in the terahertz regime. In particular, we found that the real part of the permittivity of the p-CNT film in the terahertz range is rather competitive, i.e. 8-13, however the loss tangent is not so small (0.4-0.6) as has been predicted. The way to increase p-CNT terahertz performance is also discussed.
RESUMEN
This paper investigates the electrical properties in the microwave range of a contact made by graphene nanoplatelets. The final goal is that of estimating the range of values for the equivalent electrical complex permittivity of a contact obtained by integrating low-cost graphene in the form of nanoplatelets (GNPs) into a high-frequency electrical circuit. To this end, a microstrip-like circuit is designed and realized, where the graphene nanoplatelets are self-assembled into a gap between two copper electrodes. An experimental characterization is carried out, both to study the structural properties of the nanomaterials and of the realized devices, and to measure the electromagnetic scattering parameters in the microwave range by means of a microstrip technique. A full-wave electromagnetic model is also derived and used to investigate the relationship between the measured quantities and the physical and geometrical parameters. The combined use of the experimental and simulation results allows for retrieving the values of the equivalent complex permittivity. The equivalent electrical conductivity values are found to be well below the values expected for isolated graphene nanoplatelets. The real part of the electrical relative permittivity attains values comparable to those obtained with GNP nanocomposites.
RESUMEN
Strong vibrational coherent anti-Stokes Raman scattering (CARS) signal was observed in single-wall carbon nanotubes (SWCNTs) having three different average diameters (about 0.8 nm, 1.1 nm and 1.3 nm) under optical excitation close to electronic resonance energies of nanotubes. By varying the excitation power from 1 up to 200 µW an optimal regime for non-destructive investigation of nonlinear properties of SWCNTs was determined. The possibility to detect a strong coherent nonlinear signal from small SWCNT-bundles together with CARS advantages over Raman scattering, such as high imaging rate, open new opportunities for fast three-dimensional visualisation of SWCNTs in a polymer matrix.
RESUMEN
The dielectric properties of Polymethylmetacrylate (PMMA) composites filled with CVD made multiwalled carbon nanotubes (MWCNT) of different mean outer diameters (d - 9 nm and 12-14 nm) were investigated at temperatures from 300 K to 390 K and in a wide frequency range (20 Hz-1 MHz). The percolation threshold is lower in composites with thick nanotubes. Below percolation threshold the dielectric permittivity was found also to be higher for composites with thicker carbon nanotubes. The temperature dependence of the complex dielectric permittivity of the investigated composites below percolation is mainly caused by beta relaxation in pure PMMA polymer matrix. The potential barrier for PMMA molecules rotation is higher in composites with thicker MWCNT and demonstrates non-monotonous concentration dependence.
RESUMEN
We analyzed the electromagnetic (EM) shielding effectiveness in the Ka band (26 to 37 GHz) of highly amorphous nanometrically thin pyrolytic carbon (PyC) films with lateral dimensions of 7.2 × 3.4 mm2, which consists of randomly oriented and intertwined graphene flakes with a typical size of a few nanometers. We discovered that the manufactured PyC films, whose thickness is thousand times less than the skin depth of conventional metals, provide a reasonably high EM attenuation. The latter is caused by absorption losses that can be as high as 38% to 20% in the microwave frequency range. Being semi-transparent in visible and infrared spectral ranges and highly conductive at room temperature, PyC films emerge as a promising material for manufacturing ultrathin microwave (e.g., Ka band) filters and shields.
RESUMEN
Electromagnetic absorption and subsequent heating of nanoparticle solutions and simple NaCl ionic solutions is examined for biomedical applications in the radiofrequency range at 13.56 MHz. It is shown via both theory and experiment that for in vitro measurements the shape of the solution container plays a major role in absorption and heating.
