RESUMEN
Air-coupled ultrasound (ACU) is increasingly used for nondestructive testing (NDT). With ACU, no contact or coupling agent (e.g., water and ultrasound gel) is needed between transducers and test sample, which provides high measurement reproducibility. However, for testing in production, a minimum separation is often necessary between the sample and the transducers to avoid contamination or transducer damage. Due to wave diffraction, the collimation of the ultrasound beam decreases for larger propagation distances, and ACU images become blurred and show lower defect lateral resolution with increasing sample-transducer separation. This is especially critical to thick composites, where large-size planar sources are used to bridge the large ACU transmission loss with good collimation. In this work, ACU reradiation in unbounded media is extended to NDT of multilayered composites. The extended method is named ACU time reversal (ACU-TR) and significantly improves the defect resolution of ACU imaging. With ACU-TR, the complete pressure distribution radiated by large ACU source is measured with point receivers (RXs) in one plane arbitrarily separated from the sample. By applying acoustic holography physics, it is then possible to quantitatively reconstruct the pressure field directly at arbitrary sample defect planes, which compensates for undesired diffraction phenomena and improves minimum detectable defect size, thereby achieving subwavelength lateral resolution. We tested the method on complex wood-based composite samples based on the ACU far-field measurements at a separation of 160 mm between the sample and the RX transducer. With the proposed method, it is possible to detect surface defects as well as inner defects within composite boards. In the future, by using point RX arrays instead of a scanned microphone, both data acquisition and evaluation can be potentially implemented in real time.
RESUMEN
Medical ultrasonic arrays are typically characterized in controlled water baths using measurements by a hydrophone, which can be translated with a positioning stage. Characterization of 3D acoustic fields conventionally requires measurements at each spatial location, which is tedious and time-consuming, and may be prohibitive given limitations of experimental setup (e.g., the bath and stage) and measurement equipment (i.e., the hydrophone). Moreover, with the development of new ultrasound sequences and modalities, multiple measurements are often required to characterize each imaging mode to ensure performance and clinical safety. Acoustic holography allows efficient characterization of source transducer fields based on single plane measurements. In this work, we explore the applicability of a re-radiation method based on the Rayleighâ»Sommerfeld integral to medical imaging array characterization. We show that source fields can be reconstructed at single crystal level at wavelength resolution, based on far-field measurements. This is herein presented for three practical application scenarios: for identifying faulty transducer elements; for characterizing acoustic safety parameters in focused ultrasound sequences from 2D planar measurements; and for estimating arbitrary focused fields based on calibration from an unfocused sound field and software beamforming. The results experimentally show that the acquired pressure fields closely match those estimated using our technique.
RESUMEN
Quantitative and reproducible air-coupled ultrasound (ACU) testing requires characterization of the volumetric pressure fields radiated by ACU probes. In this paper, a closed-form reradiation method combining the Rayleigh-Sommerfeld integral and time-reversal acoustics is proposed, which allows calculation of both near- field and far-field based on a single-plane measurement. The method was validated for both 3-D (circular, square) and 2-D (rectangular) planar transducers in the 50-230 kHz range. The pressure fields were scanned with a calibrated microphone. The measurement window was at least four times the size of the transducer area and the grid step size was one third of the wavelength. Best results were observed by acquiring the measurement plane at near-field distance. The method accurately reproduces pulsed ultrasound waveforms and pressure distributions (RMSE <2.5% in far field and <5.5% in near field), even at the transducer radiation surface. The effects of speed of sound drifts during the scan in the pressure were negligible (RMSE <0.3%). The reradiation method clearly outperforms conventional baffled piston models. Possible applications are transducer manufacture control (imperfections at radiation surface) and calibration (on-axis pressure, side lobes, and beamwidth) together with generation of accurate source functions for quantitative nondestructive evaluation inverse problems.
