A Preclinical Trial Protocol Using an Ovine Model to Assess Scaffold Implant Biomaterials for Repair of Critical-Sized Mandibular Defects.

The present work describes a preclinical trial (in silico, in vivo and in vitro) protocol to assess the biomechanical performance and osteogenic capability of 3D-printed polymeric scaffolds implants used to repair partial defects in a sheep mandible. The protocol spans multiple steps of the medical device development pipeline, including initial concept design of the scaffold implant, digital twin in silico finite element modeling, manufacturing of the device prototype, in vivo device implantation, and in vitro laboratory mechanical testing. First, a patient-specific one-body scaffold implant used for reconstructing a critical-sized defect along the lower border of the sheep mandible ramus was designed using on computed-tomographic (CT) imagery and computer-aided design software. Next, the biomechanical performance of the implant was predicted numerically by simulating physiological load conditions in a digital twin in silico finite element model of the sheep mandible. This allowed for possible redesigning of the implant prior to commencing in vivo experimentation. Then, two types of polymeric biomaterials were used to manufacture the mandibular scaffold implants: poly ether ether ketone (PEEK) and poly ether ketone (PEK) printed with fused deposition modeling (FDM) and selective laser sintering (SLS), respectively. Then, after being implanted for 13 weeks in vivo, the implant and surrounding bone tissue was harvested and microCT scanned to visualize and quantify neo-tissue formation in the porous space of the scaffold. Finally, the implant and local bone tissue was assessed by in vitro laboratory mechanical testing to quantify the osteointegration. The protocol consists of six component procedures: (i) scaffold design and finite element analysis to predict its biomechanical response, (ii) scaffold fabrication with FDM and SLS 3D printing, (iii) surface treatment of the scaffold with plasma immersion ion implantation (PIII) techniques, (iv) ovine mandibular implantation, (v) postoperative sheep recovery, euthanasia, and harvesting of the scaffold and surrounding host bone, microCT scanning, and (vi) in vitro laboratory mechanical tests of the harvested scaffolds. The results of microCT imagery and 3-point mechanical bend testing demonstrate that PIII-SLS-PEK is a promising biomaterial for the manufacturing of scaffold implants to enhance the bone-scaffold contact and bone ingrowth in porous scaffold implants. MicroCT images of the harvested implant and surrounding bone tissue showed encouraging new bone growth at the scaffold-bone interface and inside the porous network of the lattice structure of the SLS-PEK scaffolds.

Protecting Orthopaedic Implants from Infection: Antimicrobial Peptide Mel4 Is Non-Toxic to Bone Cells and Reduces Bacterial Colonisation When Bound to Plasma Ion-Implanted 3D-Printed PAEK Polymers.

Even with the best infection control protocols in place, the risk of a hospital-acquired infection of the surface of an implanted device remains significant. A bacterial biofilm can form and has the potential to escape the host immune system and develop resistance to conventional antibiotics, ultimately causing the implant to fail, seriously impacting patient well-being. Here, we demonstrate a 4 log reduction in the infection rate by the common pathogen S. aureus of 3D-printed polyaryl ether ketone (PAEK) polymeric surfaces by covalently binding the antimicrobial peptide Mel4 to the surface using plasma immersion ion implantation (PIII) treatment. The surfaces with added texture created by 3D-printed processes such as fused deposition-modelled polyether ether ketone (PEEK) and selective laser-sintered polyether ketone (PEK) can be equally well protected as conventionally manufactured materials. Unbound Mel4 in solution at relevant concentrations is non-cytotoxic to osteoblastic cell line Saos-2. Mel4 in combination with PIII aids Saos-2 cells to attach to the surface, increasing the adhesion by 88% compared to untreated materials without Mel4. A reduction in mineralisation on the Mel4-containing surfaces relative to surfaces without peptide was found, attributed to the acellular portion of mineral deposition.

Novel Sheep Model to Assess Critical-Sized Bone Regeneration with Periosteum for In Vivo Bioreactors.

Considerable research is being undertaken to develop novel biomaterials-based approaches for surgical reconstruction of bone defects. This extends to three-dimensional (3D) printed materials that provide stable, structural, and functional support in vivo. However, few preclinical models can simulate in vivo human biological conditions for clinically relevant testing. In this study we describe a novel ovine model that allows evaluation of in vivo osteogenesis via contact with bone and/or periosteum interfaced with printed polymer bioreactors loaded with biomaterial bone substitutes. The infraspinous scapular region of 14 Dorset cross sheep was exposed. Vascularized periosteum was elevated either attached to the infraspinatus muscle or separately. In both cases, the periosteum was supplied by the periosteal branch of the circumflex scapular vessels. In eight sheep, a 3D printed 4-chambered polyetheretherketone bioreactor was wrapped circumferentially in vascularized periosteum. In 6 sheep, 12 double-sided 3D printed 2-chambered polyetherketone bioreactors were secured to the underlying bone allowing direct contact with the bone on one side and periosteum on the other. Our model enabled simultaneous testing of up to 24 (12 double-sided) 10 × 10 × 5 mm bioreactors per scapula in the flat contact approach or a single 40 × 10 mm four-chambered bioreactor per scapula using the periosteal wrap. De novo bone growth was evaluated using histological and radiological analysis. Of importance, the experimental model was well tolerated by the animals and provides a versatile approach for comparing the osteogenic potential of cambium on the bone surface and elevated with periosteum. Furthermore, the periosteal flaps were sufficiently large for encasing bioreactors containing biomaterial bone substitutes for applications such as segmental mandibular reconstruction.

Extensively Microtwinned Diamond with Nanolaminates of Lonsdaleite Formed by Flash Laser Heating of Glassy Carbon.

Diamond's unique properties on the nanoscale make it one of the most important materials for use in biosensors and quantum computing and for components that can withstand the harsh environments of space. We synthesize oriented, faceted diamond particles by flash laser heating of glassy carbon at 16 GPa and 2300 K. Detailed transmission electron microscopy shows them to consist of a mosaic of diamond nanocrystals frequently joined at twin boundaries forming microtwins. Striking 3-fold translational periodicity was observed in both imaging and diffraction. This periodicity was shown to originate from nanodimensional wedge-shaped overlapping regions of twinned diamond and not from a possible 9R polytype, which has also been reported in other group IVa elements and water ice. Extended bilayers of hexagonal layer stacking were observed, forming lonsdaleite nanolaminates. The particles exhibited optical fluorescence with a rapid quench time (<1 ns) attributed to their unique twinned microstructure.

A Comparison of In Vivo Bone Tissue Generation Using Calcium Phosphate Bone Substitutes in a Novel 3D Printed Four-Chamber Periosteal Bioreactor.

Autologous bone replacement remains the preferred treatment for segmental defects of the mandible; however, it cannot replicate complex facial geometry and causes donor site morbidity. Bone tissue engineering has the potential to overcome these limitations. Various commercially available calcium phosphate-based bone substitutes (Novabone®, BioOss®, and Zengro®) are commonly used in dentistry for small bone defects around teeth and implants. However, their role in ectopic bone formation, which can later be applied as vascularized graft in a bone defect, is yet to be explored. Here, we compare the above-mentioned bone substitutes with autologous bone with the aim of selecting one for future studies of segmental mandibular repair. Six female sheep, aged 7-8 years, were implanted with 40 mm long four-chambered polyether ether ketone (PEEK) bioreactors prepared using additive manufacturing followed by plasma immersion ion implantation (PIII) to improve hydrophilicity and bioactivity. Each bioreactor was wrapped with vascularized scapular periosteum and the chambers were filled with autologous bone graft, Novabone®, BioOss®, and Zengro®, respectively. The bioreactors were implanted within a subscapular muscle pocket for either 8 weeks (two sheep), 10 weeks (two sheep), or 12 weeks (two sheep), after which they were removed and assessed by microCT and routine histology. Moderate bone formation was observed in autologous bone grafts, while low bone formation was observed in the BioOss® and Zengro® chambers. No bone formation was observed in the Novabone® chambers. Although the BioOss® and Zengro® chambers contained relatively small amounts of bone, endochondral ossification and retained hydroxyapatite suggest their potential in new bone formation in an ectopic site if a consistent supply of progenitor cells and/or growth factors can be ensured over a longer duration.

Neuromorphic sensing of biomolecules covalently immobilised on polydimethyl glutarimide.

Polydimethyl glutarimide (PMGI) layers with sub-micron thicknesses have been modified in a 2.5 kV Ar plasma immersion ion implantation (PIII) process to introduce free radical covalent binding sites. The surface roughness of the PMGI increased after the PIII treatment but no through-layer defects were observed. When applied to the treated PMGI, horseradish peroxidase (HRP) enzyme remained bound to the surface after extended immersion in sodium dodecyl sulfate solution (SDS). Hence, covalent binding between the activated surface and enzyme was confirmed. This covalent binding was achieved up to 24-h after the PIII process. The treated PMGI was then incorporated as a gate dielectric layer within a lateral three-terminal electrolyte-gated device. The device output characteristics resembled those of post-synaptic outputs; as successive (pre-synaptic) voltage pulses were applied to the gate, paired pulse depression and spike rate dependent plasticity were observed in the source-drain (post-synaptic) current. These characteristics were altered by the presence of HRP immobilised on the plasma-modified PMGI gate dielectric layer thus providing readout detection. These results and preliminary device characteristics show the potential for the plasma functionalized PMGI as a sensitive and reproducible biosensing technology.

An omics approach to delineating the molecular mechanisms that underlie the biological effects of physical plasma.

The use of physical plasma to treat cancer is an emerging field, and interest in its applications in oncology is increasing rapidly. Physical plasma can be used directly by aiming the plasma jet onto cells or tissue, or indirectly, where a plasma-treated solution is applied. A key scientific question is the mechanism by which physical plasma achieves selective killing of cancer over normal cells. Many studies have focused on specific pathways and mechanisms, such as apoptosis and oxidative stress, and the role of redox biology. However, over the past two decades, there has been a rise in omics, the systematic analysis of entire collections of molecules in a biological entity, enabling the discovery of the so-called "unknown unknowns." For example, transcriptomics, epigenomics, proteomics, and metabolomics have helped to uncover molecular mechanisms behind the action of physical plasma, revealing critical pathways beyond those traditionally associated with cancer treatments. This review showcases a selection of omics and then summarizes the insights gained from these studies toward understanding the biological pathways and molecular mechanisms implicated in physical plasma treatment. Omics studies have revealed how reactive species generated by plasma treatment preferentially affect several critical cellular pathways in cancer cells, resulting in epigenetic, transcriptional, and post-translational changes that promote cell death. Finally, this review considers the outlook for omics in uncovering both synergies and antagonisms with other common cancer therapies, as well as in overcoming challenges in the clinical translation of physical plasma.

Monte Carlo calculations of radiotherapy dose distributions within and around orthopaedic implants.

Background and purpose: Cancer patients often require a titanium orthopaedic implant to support or replace lost bone. In radiation treatment, the dose distribution is perturbed causing regions of high and low dose at material interfaces. Since the survival of integrating bone tissue is critical to implant success, the aim of this study was to determine the dose distribution in and around the scaffold, when constructed from titanium or Poly-ether-ether-ketone (PEEK). Materials and methods: The dose distributions in the pores and along boundaries for three implant scaffold designs were calculated using Monte-Carlo methods in Geant4/GATE, with the material taken as titanium or PEEK. The 3D dose distributions were analysed in MATLAB and segmented using image masks, yielding the dose distributions in key regions of interest. To evaluate the effect of the predicted dose perturbations, the cell survival was calculated using the linear-quadratic model for SAOS-2 cells (bone) using experimentally determined radiation response data. Results: High dose gradients were found along the boundaries of the titanium implants, but not for the corresponding PEEK implants. The dose to the internal cavities of the titanium implants was enhanced by 10-15% near the proximal interface whereas for PEEK, there was no significant dose perturbation. The predicted perturbation caused by the titanium implant was shown to decrease the survival for SAOS-2 cells by 7% which was not found for the PEEK implants. Conclusion: PEEK was shown to be a more favourable orthopaedic implant material over titanium for cancer patients considering radiation therapy.

Pathologist-performed ultrasound-guided fine-needle aspirations of the thyroid: A single institution observational study.

BACKGROUND: Ultrasound-guided fine-needle aspiration biopsies (USFNAs) are increasingly performed by pathologists. This study was designed to assess the diagnostic yield and characterization of thyroid nodules biopsied at a teaching hospital setting in which both attending physicians and trainees are involved in the performance of USFNAs. METHODS: A retrospective study of pathologist-performed USFNAs of thyroid cases was performed over a period of 9 years at a tertiary medical center. Data collected included patient characteristics and The Bethesda System diagnostic categories. RESULTS: Over the study period, 1531 USFNAs of thyroid nodules were performed in the pathology-based clinic, with 1209 lesions in females and 322 in males. Ninety-three percent of samples were sufficient for diagnosis (n = 1420). The majority of nodules biopsied were benign (65.4%, n = 1002). Overall, 3.1% of nodules biopsied were diagnostic of malignancy (n = 47). The number of USFNAs over the years showed a rapid increase initially, with a coronavirus disease 2019-related decrease in 2020. CONCLUSIONS: The authors report their experience with thyroid USFNA over nearly a decade. The most common diagnosis was benign and the second most common was Bethesda category III. Lesions that were diagnostic of malignancy were relatively uncommon. Over the study period, the results showed that at a large tertiary care center in which USFNAs were performed by trainees as well as attending physicians, the diagnostic yield was good with a majority of thyroid nodules biopsied associated with a definitive diagnosis.

Quantifying Moisture Penetration in Encapsulated Devices by Heavy Water Mass Spectrometry: A Standard Moisture Leak Using Poly(ether-ether-ketone).

Moisture penetration into active biomedical implants such as the bionic ear and eye is a major problem in healthcare since surgery is required to replace devices affected by corrosion. Existing methods for measuring moisture leak rates such as the commercially available dynamic relative humidity method are not sufficiently sensitive to guarantee security against moisture penetration. Helium leak detection is highly sensitive but is challenged by the unknown relation to the moisture leak rate because of mixed flow modes involving liquid water. A standard moisture leak traceable to fundamental units is not currently available, preventing direct comparison of moisture and helium leak rates in the same device. Here, we demonstrate a practical calibrated moisture leak based on the stable polymer poly(ether-ether-ketone), for calibrating heavy water mass spectrometry. Using biomedical test structures from manufactured encapsulations, we show that in the majority of cases, calibrated measurements of molar moisture leak rates exceed the helium leak rate, especially for very small and large leaks. Comparison with theory shows that LaPlace pressure is the driving force for the enhanced moisture flows. We recommend that the compliance limit for helium testing in biomedical devices be reduced by one order of magnitude.

Investigation of Room Temperature Formation of the Ultra-Hard Nanocarbons Diamond and Lonsdaleite.

Diamond is an attractive material due to its extreme hardness, high thermal conductivity, quantum optical, and biomedical applications. There is still much that is not understood about how diamonds form, particularly at room temperature and without catalysts. In this work, a new route for the formation of nanocrystalline diamond and the diamond-like phase lonsdaleite is presented. Both diamond phases are found to form together within bands with a core-shell structure following the high pressure treatment of a glassy carbon precursor at room temperature. The crystallographic arrangements of the diamond phases revealed that shear is the driving force for their formation and growth. This study gives new understanding of how shear can lead to crystallization in materials and helps elucidate how diamonds can form on Earth, in meteorite impacts and on other planets. Finally, the new shear induced formation mechanism works at room temperature, a key finding that may enable diamond and other technically important nanomaterials to be synthesized more readily.

Covalent Immobilization of N-Acetylcysteine on a Polyvinyl Chloride Substrate Prevents Bacterial Adhesion and Biofilm Formation.

Biofilm formation and antimicrobial resistance at surgical implant sites result in high morbidity and mortality. Identifying novel molecules that inhibit biofilm formation to coat surgical biomaterials is essential. One such compound is N-acetylcysteine (NAC), a potent antioxidant precursor for glutathione, necessary in mammalian cells and known to disrupt/prevent biofilms. In this study, NAC was covalently immobilized onto functionalized polyvinyl chloride surfaces using plasma immersion ion implantation (PIII) treatment that achieves covalent binding without the need for linker groups. NAC immobilization was characterized using water contact angles, Fourier-transform infrared, and X-ray photoelectron spectroscopy techniques. Bacterial viability and biofilm formation on NAC surfaces were assessed using resazurin assays, phase contrast microscopy, and colony counting experiments. Effect of NAC on bacterial polysaccharide production and DNA cleaving was investigated using the phenol-sulfuric acid method and the Qubit fluorometer. Surface thermodynamics between the NAC coating and bacterial cells were measured using the Lewis acid-base method. Surface characterization techniques demonstrated superficial changes after PIII treatment and subsequent covalent NAC immobilization. NAC-coated surfaces significantly reduced biofilm viability and the presence of Gram-negative and Gram-positive bacteria. NAC also decreased polysaccharide production and degraded DNA. This led to unfavorable conditions for biofilm formation on NAC-coated surfaces, as demonstrated by surface thermodynamic analysis. NAC-coated surfaces showed no cytotoxicity to human fibroblast cells. This study has successfully utilized NAC as an antibiofilm coating, which may pave the way for improved prophylactic coatings on medical implant devices in the future.

Cancer treatment with gas plasma and with gas plasma-activated liquid: positives, potentials and problems of clinical translation.

Gas plasmas, created in atmospheric pressure conditions, both thermal (hot) and non-thermal (cold) are emerging as useful tools in medicine. During surgery, hot gas plasmas are useful to reduce thermal damage and seal blood vessels. Gas plasma pens use cold gas plasma to produce reactive chemical species with selective action against cancers, which can be readily exposed in surgery or treated from outside of the body. Solutions activated by cold gas plasma have potential as a novel treatment modality for treatment of less readily accessible tumours, or those with high metastatic potential. This review summarises the preclinical and clinical trial evidence currently available, as well as the challenges for translation of direct gas plasma and gas plasma-activated solution treatment into regular practice.

Atmospheric Pressure Plasma Jet Treatment of Polymers Enables Reagent-Free Covalent Attachment of Biomolecules for Bioprinting.

Three-dimensional (3D) bioprinting, where cells, hydrogels, and structural polymers can be printed layer by layer into complex designs, holds great promise for advances in medicine and the biomedical sciences. In principle, this technique enables the creation of highly patient-specific disease models and biomedical implants. However, an ability to tailor surface biocompatibility and interfacial bonding between printed components, such as polymers and hydrogels, is currently lacking. Here we demonstrate that an atmospheric pressure plasma jet (APPJ) can locally activate polymeric surfaces for the reagent-free covalent attachment of proteins and hydrogel in a single-step process at desired locations. Polyethylene and poly-ε-caprolactone were used as example polymers. Covalent attachment of the proteins and hydrogel was demonstrated by resistance to removal by rigorous sodium dodecyl sulfate washing. The immobilized protein and hydrogel layers were analyzed using Fourier transform infrared and X-ray photoelectron spectroscopy. Importantly, the APPJ surface activation also rendered the polymer surfaces mildly hydrophilic as required for optimum biocompatibility. Water contact angles were observed to be stable within a range where the conformation of biomolecules is preserved. Single and double electrode designs of APPJs were compared in their characteristics relevant to localized surface functionalization, plume length, and shape. As a proof of efficacy in a biological context, APPJ-treated polyethylene functionalized with fibronectin was used to demonstrate improvements in cell adhesion and proliferation. These results have important implications for the development of a new generation of 3D bioprinters capable of spatially patterned and tailored surface functionalization performed during the 3D printing process in situ.

Covalent Biofunctionalization of the Inner Surfaces of a Hollow-Fiber Capillary Bundle Using Packed-Bed Plasma Ion Implantation.

Hollow-fiber capillary bundles are widely used in the production of medical devices for blood oxygenation and purification purposes such as in cardiopulmonary bypass, hemodialysis, and hemofiltration, but the blood interfacing inner surfaces of these capillaries provide poor hemocompatibility. Here, we present a novel method of packed-bed plasma ion implantation (PBPII) for the modification of the inner surfaces of polymeric hollow-fiber bundles enclosed in a cassette. The method is simple and can be performed on an intact hollow-fiber bundle cassette by the placement of a hollow cylindrical electrode, connected to a negative high-voltage pulse generator, around the cassette. The method does not require the insertion of electrodes inside the capillaries or the cassette. Nitrogen gas is fed into the capillaries inside the cassette by connecting the inlet of the cassette to a gas source. Upon the application of negative high-voltage bias pulses to the electrode, plasma is ignited inside the cassette, achieving the surface modification of both the internal and external surfaces of the capillaries. Fourier transform infrared-attenuated total reflectance spectroscopy of the PBPII-treated capillaries revealed the formation of aromatic C═C bonds, indicating the progressive carbonization of the capillary surfaces. The PBPII treatment was found to be uniform along the capillaries and independent of the radial position in the cassette. Atomic force microscopy of cross sections through the capillaries revealed that the increased stiffness associated with the carbonized layer on the inner surface of the PBPII-treated capillary has a depth (∼40 nm) consistent with that expected for ions accelerated by the applied bias voltage. The modified internal surfaces of the capillary bundle showed a greatly increased wettability and could be biofunctionalized by covalently immobilizing protein directly from the buffer solution. The direct, reagent-free protein immobilization was demonstrated using tropoelastin as an example protein. Covalent binding of the protein was confirmed by its resistance to removal by hot sodium dodecyl sulfate detergent washing, which is known to disrupt physical binding.

Gas chromatography-mass spectrometry analyses of encapsulated stable perovskite solar cells.

Although perovskite solar cells have produced remarkable energy conversion efficiencies, they cannot become commercially viable without improvements in durability. We used gas chromatography-mass spectrometry (GC-MS) to reveal signature volatile products of the decomposition of organic hybrid perovskites under thermal stress. In addition, we were able to use GC-MS to confirm that a low-cost polymer/glass stack encapsulation is effective in suppressing such outgassing. Using such an encapsulation scheme, we produced multi-cation, multi-halide perovskite solar cells containing methylammonium that exceed the requirements of the International Electrotechnical Commission 61215:2016 standard by surviving more than 1800 hours of the Damp Heat test and 75 cycles of the Humidity Freeze test.

Atomic-Scale Patterning of Arsenic in Silicon by Scanning Tunneling Microscopy.

Over the past two decades, prototype devices for future classical and quantum computing technologies have been fabricated by using scanning tunneling microscopy and hydrogen resist lithography to position phosphorus atoms in silicon with atomic-scale precision. Despite these successes, phosphine remains the only donor precursor molecule to have been demonstrated as compatible with the hydrogen resist lithography technique. The potential benefits of atomic-scale placement of alternative dopant species have, until now, remained unexplored. In this work, we demonstrate the successful fabrication of atomic-scale structures of arsenic-in-silicon. Using a scanning tunneling microscope tip, we pattern a monolayer hydrogen mask to selectively place arsenic atoms on the Si(001) surface using arsine as the precursor molecule. We fully elucidate the surface chemistry and reaction pathways of arsine on Si(001), revealing significant differences to phosphine. We explain how these differences result in enhanced surface immobilization and in-plane confinement of arsenic compared to phosphorus, and a dose-rate independent arsenic saturation density of 0.24 ± 0.04 monolayers. We demonstrate the successful encapsulation of arsenic delta-layers using silicon molecular beam epitaxy, and find electrical characteristics that are competitive with equivalent structures fabricated with phosphorus. Arsenic delta-layers are also found to offer confinement as good as similarly prepared phosphorus layers, while still retaining >80% carrier activation and sheet resistances of <2 kΩ/square. These excellent characteristics of arsenic represent opportunities to enhance existing capabilities of atomic-scale fabrication of dopant structures in silicon, and may be important for three-dimensional devices, where vertical control of the position of device components is critical.

Imaging prior to radiotherapy impacts in-vitro survival.

BACKGROUND AND PURPOSE: Cone Beam Computed Tomography (CBCT) is routinely used in radiotherapy to identify the position of the target volume. The aim of this study was to determine whether the CBCT dose, when followed by the treatment, influences the therapeutic outcomes as determined by in-vitro clonogenic cell survival in a radiobiological experiment. MATERIALS AND METHODS: Human cell lines, four cancer and one normal, were exposed to a 6 MV photon beam, produced by a linear accelerator. For half of each sample, a prior imaging dose was delivered using the on-board CBCT. A sample size of n = 103 was used to achieve statistical power. RESULTS: The experimental group of cell lines exposed to CBCT imaging prior to treatment exhibited a reduction in mean cancer cell survival of ~17 times (p = 0.02) greater than predicted from the average dose response and equivalent to more than 5% of the therapeutic dose, compared to 11 times greater than predicted for normal cells (n.s.). CONCLUSION: The greater than predicted reduction in survival resulting from the additional CBCT dose is consistent with radiation-induced bystander effects.

Linker-protein G mediated functionalization of polystyrene-encapsulated upconversion nanoparticles for rapid gene assay using convective PCR.

The authors report on a simplified approach to encapsulate upconversion nanoparticles (UCNPs) in polystyrene spheres by mini-emulsion polymerisation. The resulting particles (PS-UCNP) are hydrophilic, stable and suitable for biomolecular recognition and biosensing applications. Also, a strategy was developed for bioconjugation of antibodies onto the surface of the PS-UCNPs by using the bifunctional fusion protein linker-protein G (LPG). LPG mediates the functionalisation of PS-UCNPs with antibodies against digoxigenin allowing for specific labelling of convective PCR (cPCR) amplicons. Lambda DNA was amplified using cPCR on a heat block for 30 min using the digoxigenin labelled forward and biotin labelled reverse primers. The antibody functionalised PS-UCNPs bind to the digoxigenin end of the cPCR amplicons. Finally, the streptavidin labelled magnetic beads were used to selectively capture the PS-UCNP-labelled cPCR amplicons and the upconversion signal was detected at 537 nm under 980 nm excitation. This sandwich approach enables direct recognition of the target lambda DNA with a detection limit of 103 copies µL-1. The upconversion signal decreased proportionally to the concentration of the lambda DNA with a linear response between 107 and 103 copies of DNA. Graphical abstract Schematic representation of polystyrene-encapsulated upconversion nanoparticles (PS-UCNPs) prepared by mini-emulsion polymerisation. The PS-UCNPs were functionalised with anti-digoxigenin antibody using the fusion protein linker-protein G (LPG). Detection of digoxigenin-labelled amplicons is achieved (a) by using the antibody-functionalised LPG@PS-UCNP labels; (b) magnetic separation, and (c) 980 nm laser light for detection of the green upconversion luminescence peaking at 537 nm.

Tin oxide artificial synapses for low power temporal information processing.

Lateral memristors configured with inert Pt contacts and mixed phase tin oxide layers have exhibited immediate, forming-free, low-power bidirectional resistance switching. Activity dependent conductance and relaxation in the low resistance state resembled short term potentiation in biological synapses. After scanning probe microscopy, x-ray photoelectron spectroscopy and electrical measurements, the device characteristics were attributed to Joule heating induced decomposition of the minority SnO phase and formation of a SnO2 conducting filament with higher effective n-type doping. Finally, the devices recognized input voltage pulse sequences and spectral data by returning unique conductance states, suggesting suitability for bio-inspired pattern recognition systems.