From Material to Cameras: Low-Dimensional Photodetector Arrays on CMOS.

The last two decades have witnessed a dramatic increase in research on low-dimensional material with exceptional optoelectronic properties. While low-dimensional materials offer exciting new opportunities for imaging, their integration in practical applications has been slow. In fact, most existing reports are based on single-pixel devices that cannot rival the quantity and quality of information provided by massively parallelized mega-pixel imagers based on complementary metal-oxide semiconductor (CMOS) readout electronics. The first goal of this review is to present new opportunities in producing high-resolution cameras using these new materials. New photodetection methods and materials in the field are presented, and the challenges involved in their integration on CMOS chips for making high-resolution cameras are discussed. Practical approaches are then presented to address these challenges and methods to integrate low-dimensional material on CMOS. It is also shown that such integrations could be used for ultra-low noise and massively parallel testing of new material and devices. The second goal of this review is to present the colossal untapped potential of low-dimensional material in enabling the next-generation of low-cost and high-performance cameras. It is proposed that low-dimensional materials have the natural ability to create excellent bio-inspired artificial imaging systems with unique features such as in-pixel computing, multi-band imaging, and curved retinas.

A New Approach to Designing High-Sensitivity Low-Dimensional Photodetectors.

Photodetectors fabricated from low-dimensional materials such as quantum dots, nanowires, and two-dimensional materials show tremendous promise based on reports of very high responsivities. However, it is not generally appreciated that maximizing the internal gain may compromise the detector performance at low light levels, reducing its sensitivity. Here, we show that for most low-dimensional photodetectors with internal gain the sensitivity is determined by the junction capacitance. Thanks to their extremely small junction capacitances and reduced charge screening, low-dimensional materials and devices provide clear advantages over bulk semiconductors in the pursuit of high-sensitivity photodetectors. This mini-review describes and validates a method to estimate the capacitance from external photoresponse measurements, providing a straightforward approach to extract the device sensitivity and benchmark against physical limits. This improved physical understanding can guide the design of low-dimensional photodetectors to effectively leverage their unique advantage and achieve sensitivities that can exceed that of the best existing photodetectors.

A 3 pJ/bit free space optical interlink platform for self-powered tetherless sensing and opto-spintronic RF-to-optical transduction.

Tetherless sensors have long been positioned to enable next generation applications in biomedical, environmental, and industrial sectors. The main challenge in enabling these advancements is the realization of a device that is compact, robust over time, and highly efficient. This paper presents a tetherless optical tag which utilizes optical energy harvesting to realize scalable self-powered devices. Unlike previous demonstrations of optically coupled sensor nodes, the device presented here amplifies signals and encodes data on the same optical beam that provides its power. This optical interrogation modality results in a highly efficient data link. These optical tags support data rates up to 10 Mb/s with an energy consumption of ~ 3 pJ/bit. As a proof-of-concept application, the optical tag is combined with a spintronic microwave detector based on a magnetic tunnel junction (MTJ). We used this hybrid opto-spintronic system to perform self-powered transduction of RF waves at 1 GHz to optical frequencies at ~ 200 THz, while carrying an audio signal across (see Supplementary Data for audio files).

When shot-noise-limited photodetectors disobey Poisson statistics.

Photodetectors with internal gain are of great interest for imaging applications, since internal gain reduces the effective noise of readout electronics. High-gain photodetectors have been demonstrated, but only individually rather than as a full array in a camera. Consequently, there has been little investigation of the interaction between camera complementary metal oxide semiconductor (CMOS) electronics and the slow response time that high-gain photodetectors often exhibit. Here we show that this interaction filters shot noise and causes noise statistics to differ from the common Poisson distribution. As an example, we investigate a 320×256 array of InGaAs/InP high-gain phototransistors bonded to a CMOS readout chip. We demonstrate the filtering effects and discuss their consequences, including new (to the best of our knowledge) methods for extracting gain and increasing dynamic range.

Dynamically Reconfigurable Data Readout of Pixel Detectors for Automatic Synchronization with Data Acquisition Systems.

Reconfigurable detectors with dynamically selectable sensing and readout modes are highly desirable for implementing edge computing as well as enabling advanced imaging techniques such as foveation. The concept of a camera system capable of simultaneous passive imaging and dynamic ranging in different regions of the detector is presented. Such an adaptive-autonomous detector with both spatial and temporal control requires programmable window of exposure (time frames), ability to switch between readout modes such as full-frame imaging and zero-suppressed data, modification of the number of pixel data bits and independent programmability for distinct detector regions. In this work, a method is presented for seamlessly changing time frames and readout modes without data corruption while still ensuring that the data acquisition system (DAQ) does not need to stop and resynchronize at each change of setting, thus avoiding significant dead time. Data throughput is maximized by using a minimum unique data format, rather than lengthy frame headers, to differentiate between consecutive frames. A data control and transmitter (DCT) synchronizes data transfer from the pixel to the periphery, reconfigures the data to transmit it serially off-chip, while providing optimized decision support based on a DAQ definable mode. Measurements on a test structure demonstrate that the DCT can operate at 1 GHz in a 65 nm LP CMOS process.

Recent advances in infrared imagers: toward thermodynamic and quantum limits of photon sensitivity.

Infrared detection and imaging are key enabling technologies for a vast number of applications, ranging from communication, to medicine and astronomy, and have recently attracted interest for their potential application in optical interconnects and quantum computing. Nonetheless, infrared detection still constitutes the performance bottleneck for several of these applications, due to a number of unsolved challenges, such as limited quantum efficiency, yield and scalability of the devices, as well as limited sensitivity and low operating temperatures. The current commercially dominating technologies are based on planar semiconducting PIN or avalanche detectors. However, recent developments in semiconductor technology and nano-scale materials have enabled significant technological advancement, demonstrating the potential for groundbreaking achievements in the field. We review the recent progress in the most prominent novel detection technologies, and evaluate their advantages, limitations, and prospects. We further offer a perspective on the main fundamental limits on the detectors sensitivity, and we discuss the technological challenges that need to be addressed for significative advancement of the field. Finally, we present a set of potential system-wide strategies, including nanoscale and low-dimensional detectors, light coupling enhancement strategies, advanced read-out circuitry, neuromorphic and curved image sensors, aimed at improving the overall imagers performance.

Evaluation of the Returned Electromagnetic Signal from Retro-reflectors in Turbid Media.

We provide first-principle theoretical and numerical simulations using the coherent Transfer Matrix Approach (TMA) to describe the behavior of the three main class of the optical beacons namely phase conjugators, reflectors, and retroreflectors within a turbid medium. Our theory describes the extraordinary enhancement (about 5 dB) offered by retroreflectors compared to reflectors in our detailed experiments and shows that they effectively act as local optical phase conjugators. Moreover, the performance of retroreflectors shows little degradation for increased light incident angles in turbid media, while the performance of reflectors degrades drastically. These results may find applications for detection of the echoes of electromagnetic radiation in turbid media.

Engineering the gain-bandwidth product of phototransistor diodes.

In recent years, phototransistors have considerably expanded their field of application, including for instance heterodyne detection and optical interconnects. Unlike in low-light imaging, some of these applications require fast photodetectors that can operate in relatively high light levels. Since the gain and bandwidth of phototransistors are not constant across different optical powers, the devices that have been optimized for operation in low light level cannot effectively be employed in different technological applications. We present an extensive study of the gain and bandwidth of short-wavelength infrared phototransistors as a function of optical power level for three device architectures that we designed and fabricated. The gain of the photodetectors is found to increase with increasing carrier injection. Based on a Shockley-Read-Hall recombination model, we show that this is due to the saturation of recombination centers in the phototransistor base layer. Eventually, at a higher light level, the gain drops, due to the Kirk effect. As a result of these opposing mechanisms, the gain-bandwidth product is peaked at a given power level, which depends on the device design and material parameters, such as doping and defect density. Guided by this physical understanding, we design and demonstrate a phototransistor which is capable of reaching a high gain-bandwidth product for high-speed applications. The proposed design criteria can be employed in conjunction with the engineering of the device size to achieve a wide tunability of the gain and bandwidth, hence paving the way toward fast photodetectors for applications with different light levels.

Characterization of the Optical Properties of Turbid Media by Supervised Learning of Scattering Patterns.

Fabricated tissue phantoms are instrumental in optical in-vitro investigations concerning cancer diagnosis, therapeutic applications, and drug efficacy tests. We present a simple non-invasive computational technique that, when coupled with experiments, has the potential for characterization of a wide range of biological tissues. The fundamental idea of our approach is to find a supervised learner that links the scattering pattern of a turbid sample to its thickness and scattering parameters. Once found, this supervised learner is employed in an inverse optimization problem for estimating the scattering parameters of a sample given its thickness and scattering pattern. Multi-response Gaussian processes are used for the supervised learning task and a simple setup is introduced to obtain the scattering pattern of a tissue sample. To increase the predictive power of the supervised learner, the scattering patterns are filtered, enriched by a regressor, and finally characterized with two parameters, namely, transmitted power and scaled Gaussian width. We computationally illustrate that our approach achieves errors of roughly 5% in predicting the scattering properties of many biological tissues. Our method has the potential to facilitate the characterization of tissues and fabrication of phantoms used for diagnostic and therapeutic purposes over a wide range of optical spectrum.

Open architecture time of flight 3D SWIR camera operating at 150 MHz modulation frequency.

In the past two decades 3-D cameras have proven to be one of the next revolutions in machine vision. However, these devices are still an emerging technology with a particularly narrow set of commercially available devices. In this paper, the concept and execution of the first short wavelength infrared (SWIR) time-of-flight (ToF) 3-D camera system operating at a wavelength of 1550 nm is presented. By decoupling the optical and electrical components of the system in an open architecture we not only surpass many of the limitations of an on-chip integrated solution, but also can easily change the imaging device based on the requirements of the application. We achieve modulation frequencies up to 150 MHz, which exceeds the conventional values currently published for other large format modulators by about five times. This increase in the modulation frequency allows for a TOF camera with significantly higher depth resolution, while the open architecture design allows for a highly reconfigurable device that can be modified for specific working conditions.

Cascaded spintronic logic with low-dimensional carbon.

Remarkable breakthroughs have established the functionality of graphene and carbon nanotube transistors as replacements to silicon in conventional computing structures, and numerous spintronic logic gates have been presented. However, an efficient cascaded logic structure that exploits electron spin has not yet been demonstrated. In this work, we introduce and analyse a cascaded spintronic computing system composed solely of low-dimensional carbon materials. We propose a spintronic switch based on the recent discovery of negative magnetoresistance in graphene nanoribbons, and demonstrate its feasibility through tight-binding calculations of the band structure. Covalently connected carbon nanotubes create magnetic fields through graphene nanoribbons, cascading logic gates through incoherent spintronic switching. The exceptional material properties of carbon materials permit Terahertz operation and two orders of magnitude decrease in power-delay product compared to cutting-edge microprocessors. We hope to inspire the fabrication of these cascaded logic circuits to stimulate a transformative generation of energy-efficient computing.

An Optical-Fiber-Based Smart Textile (Smart Socks) to Manage Biomechanical Risk Factors Associated With Diabetic Foot Amputation.

OBJECTIVE: This study aimed to validate a smart-textile based on fiber-optics for simultaneous measurement of plantar temperature, pressure, and joint angles in patients with diabetic peripheral neuropathy (DPN). METHODS: After in-vitro validation in the laboratory, 33 eligible subjects with DPN were recruited (age: 58 ± 8 years, BMI: 31.5 ± 8 kg/m2) for assessing plantar pressure and temperature during habitual gait-speed in a clinical-setting. All participants were asked to walk at their habitual speed while wearing a pair of sensorized socks made from highly flexible fiber optics (SmartSox). An algorithm was designed to estimate temperature, pressure, and toe range of motion from optical wavelength generated from SmartSox. To validate the device, results from thermal stress response (TSR) using thermography and peak pressure measured by computerized pressure insoles (F-Scan) were used as gold standards. RESULTS: In laboratory and under controlled conditions, the agreements for parameters of interest were excellent ( r > .98, P = .000), and no noticeable cross-talks between measurements of temperature, angle, and pressure were observed. During clinical data acquisition, a significant correlation was found for pressure profile under different anatomical regions of interest between SmartSox and F-Scan ( r = .67, P < .050) as well as between thermography and SmartSox ( r = .55, P < .050). CONCLUSION: This study demonstrates the validity of an innovative smart textile for assessing simultaneously the key parameters associated with risk of foot ulcers in patients with DPN. It may empower clinicians to objectively stratify foot risk and provide timely care. Another study is warranted to validate its clinical application in preventing limb threating problems in patients with DPN.

Demonstration of Shot-noise-limited Swept Source OCT Without Balanced Detection.

Optical coherence tomography (OCT) has been utilized in a rapidly growing number of clinical and scientific applications. In particular, swept source OCT (SS-OCT) has attracted many attentions due to its excellent performance. So far however, the limitations of existing photon detectors have prevented achieving shot-noise-limited sensitivity without using balanced-detection scheme in SS-OCT, even when superconducting single-photon detectors were used. Unfortunately, balanced-detection increases OCT system size and cost, as it requires many additional components to boost the laser power and maintain near ideal balanced performance across the whole optical bandwidth. Here we show for the first time that a photon detector is capable of achieving shot noise limited performance without using the balanced-detection technique in SS-OCT. We built a system using a so-called electron-injection photodetector, with a cutoff-wavelength of 1700 nm. Our system achieves a shot-noise-limited sensitivity of about -105 dB at a reference laser power of ~350 nW, which is more than 30 times lower laser power compared with the best-reported results. The high sensitivity of the electron-injection detector allows utilization of micron-scale tunable laser sources (e.g. VCSEL) and eliminates the need for fiber amplifiers and highly precise couplers, which are an essential part of the conventional SS-OCT systems.

Simple telecentric submillimeter lens with near-diffraction-limited performance across an 80 degree field of view.

A simple and compact telecentric lens based on two hemispheric optical elements arranged in a formation resembling an "hourglass" is proposed and evaluated. Our modeling and experimental results show the ability of this lens in achieving high resolution over a large field of view. A prototype with 500 µm total thickness is built using silicon micromachining methods for a center wavelength of 1500 nm. Experimental measurement shows near-diffraction-limited performance and good telecentricity over an 80° field of view at a numerical aperture of 0.2. All elements of the hourglass lens are in direct contact, and hence the alignment is extremely simple. We believe the proposed lens is a good candidate for compact and low-cost multi-aperture imagers.

High-throughput realization of an infrared selective absorber/emitter by DUV microsphere projection lithography.

In this paper, we present a low-cost and high-throughput nanofabrication method to realize metasurfaces that have selective absorption/emission in the mid-infrared region of the electromagnetic spectrum. We have developed DUV projection lithography to produce arbitrary patterns with sub-80 nm feature sizes. As examples of practical applications, we experimentally demonstrate structures with single and double spectral absorption/emission features, and in close agreement with numerical simulation. The fundamental mechanism of perfect absorption is discussed as well. Selective infrared absorbers/emitters are critical elements in realizing efficient thermophotovoltaic cells and high-performance biosensors.

Deep-UV microsphere projection lithography.

In this Letter, we present a single-exposure deep-UV projection lithography at 254-nm wavelength that produces nanopatterns in a scalable area with a feature size of 80 nm. In this method, a macroscopic lens projects a pixelated optical mask on a monolayer of hexagonally arranged microspheres that reside on the Fourier plane and image the mask's pattern into a photoresist film. Our macroscopic lens shrinks the size of the mask by providing an imaging magnification of ∼1.86×10(4), while enhancing the exposure power. On the other hand, microsphere lens produces a sub-diffraction limit focal point-a so-called photonic nanojet-based on the near-surface focusing effect, which ensures an excellent patterning accuracy against the presence of surface roughness. Ray-optics simulation is utilized to design the bulk optics part of the lithography system, while a wave-optics simulation is implemented to simulate the optical properties of the exposed regions beneath the microspheres. We characterize the lithography performance in terms of the proximity effect, lens aberration, and interference effect due to refractive index mismatch between photoresist and substrate.

Impact of optical antennas on active optoelectronic devices.

Remarkable progress has been made in the fabrication and characterization of optical antennas that are integrated with optoelectronic devices. Herein, we describe the fundamental reasons for and experimental evidence of the dramatic improvements that can be achieved by enhancing the light-matter interaction via an optical antenna in both photon-emitting and -detecting devices. In addition, integration of optical antennas with optoelectronic devices can lead to the realization of highly compact multifunctional platforms for future integrated photonics, such as low-cost lab-on-chip systems. In this review paper, we further focus on the effect of optical antennas on the detectivity of infrared photodetectors. One particular finding is that the antenna can have a dual effect on the specific detectivity, while it can elevate light absorption efficiency of sub-wavelength detectors, it can potentially increase the noise of the detectors due to the enhanced spontaneous emission rate. In particular, we predict that the detectivity of interband photon detectors can be negatively affected by the presence of optical antennas across a wide wavelength region covering visible to long wavelength infrared bands. In contrast, the detectivity of intersubband detectors could be generally improved with a properly designed optical antenna.

Hybrid optical antenna with high directivity gain.

Coupling of a far-field optical mode to electronic states of a quantum absorber or emitter is a crucial process in many applications, including infrared sensors, single molecule spectroscopy, and quantum metrology. In particular, achieving high quantum efficiency for a system with a deep subwavelength quantum absorber/emitter has remained desirable. In this Letter, a hybrid optical antenna based on coupling of a photonic nanojet to a metallo-dielectric antenna is proposed, which allows such efficient coupling. A quantum efficiency of about 50% is predicted for a semiconductor with volume of ~λ³/170. Despite the weak optical absorption coefficient of 2000 cm(-1) in the long infrared wavelength of ~8 µm, very strong far-field coupling has been achieved, as evidenced by an axial directivity gain of 16 dB, which is only 3 dB below of theoretical limit. Unlike the common phased array antenna, this structure does not require coherent sources to achieve a high directivity. The quantum efficiency and directivity gain are more than an order of magnitude higher than existing metallic, dielectric, or metallo-dielectric optical antenna.