A reversible water-based electrostatic adhesive.

Commercial adhesives typically fall into two categories: structural or pressure sensitive. Structural glues rely on covalent bonds formed during curing and provide high tensile strength whilst pressure-sensitive adhesives use physical bonding to provide weaker adhesion, but with considerable convenience for the user. Here, a new class of adhesive is presented that is also reversible, with a bond strength intermediate between those of pressure-sensitive and structural adhesives. Complementary water-based formulations incorporating oppositely charged polyelectrolytes form electrostatic bonds that may be reversed through immersion in a low or high pH aqueous environment. This electrostatic adhesive has the advantageous property that it exhibits good adhesion to low-energy surfaces such as polypropylene. Furthermore, it is produced by the emulsion copolymerization of commodity materials, styrene and butyl acrylate, which makes it inexpensive and opens the possibility of industrial production. Bio-based materials have been also integrated into the formulations to further increase sustainability. Moreover, unlike other water-based glues, adhesion does not significantly degrade in humid environments. Because such electrostatic adhesives do not require mechanical detachment, they are appropriate for the large-scale recycling of, e.g., bottle labels or food packaging. The adhesive is also suitable for dismantling components in areas as varied as automotive parts and electronics.

Vac-and-fill: A micromoulding technique for fabricating microneedle arrays with vacuum-activated, hands-free mould-filling.

We report a simple and reproducible micromoulding technique that dynamically fills microneedle moulds with a liquid formulation, using a plastic syringe, triggered by the application of vacuum ('vac-and-fill'). As pressure around the syringe drops, air inside the syringe pushes the plunger to uncover an opening in the syringe and fill the microneedle mould without manual intervention, therefore removing inter-operator variability. The technique was validated by monitoring the plunger movement and pressure at which the mould would be filled over 10 vacuum cycles for various liquid formulation of varying viscosity (water, glycerol, 20 % polyvinylpyrrolidone (PVP) solution or 40 % PVP solution). Additionally, the impact of re-using the disposable syringes on plunger movement, and thus the fill pressure, was investigated using a 20 % PVP solution. The fill pressure was consistent at 300-450 mbar. It produced well-formed and mechanically robust PVP, poly(methylvinylether/maleic anhydride) and hydroxyethylcellulose microneedles from liquid formulations. This simple and inexpensive technique of micromoulding eliminated the air entrapment and bubble formation, which prevent reproducible microneedle formation, in the resultant microneedle arrays. It provides a cost-effective alternative to the conventional micromoulding techniques, where the application of vacuum ('fill-and-vac') or centrifugation following mould-filling may be unsuitable, ineffective or have poor reproducibility.

Effective Endotoxin Removal from Chitosan That Preserves Chemical Structure and Improves Compatibility with Immune Cells.

Chitosan is one of the most researched biopolymers for healthcare applications, however, being a naturally derived polymer, it is susceptible to endotoxin contamination, which elicits pro-inflammatory responses, skewing chitosan's performance and leading to inaccurate conclusions. It is therefore critical that endotoxins are quantified and removed for in vivo use. Here, heat and mild NaOH treatment are investigated as facile endotoxin removal methods from chitosan. Both treatments effectively removed endotoxin to below the FDA limit for medical devices (<0.5 EU/mL). However, in co-culture with peripheral blood mononuclear cells (PBMCs), only NaOH-treated chitosan prevented TNF-α production. While endotoxin removal is the principal task, the preservation of chitosan's structure is vital for the synthesis and lysozyme degradation of chitosan-based hydrogels. The chemical properties of NaOH-treated chitosan (by FTIR-ATR) were significantly similar to its native composition, whereas the heat-treated chitosan evidenced macroscopic chemical and physical changes associated with the Maillard reaction, deeming this treatment unsuitable for further applications. Degradation studies conducted with lysozyme demonstrated that the degradation rates of native and NaOH-treated chitosan-genipin hydrogels were similar. In vitro co-culture studies showed that NaOH hydrogels did not negatively affect the cell viability of monocyte-derived dendritic cells (moDCs), nor induce phenotypical maturation or pro-inflammatory cytokine release.

Interplay between biomaterials and the immune system: Challenges and opportunities in regenerative medicine.

The use of biomaterials for tissue engineering and regenerative medicine applications has increased dramatically over recent years. However, the clinical uptake of a wide variety of biomaterials remains limited due to adverse effects commonly exhibited by patients, which are caused by the host immune response. Despite this, current in vitro evaluation standards (ISO-10993) for assessing the host response to biomaterials have limitations in predicting the likelihood of in vivo biomaterial acceptance. Furthermore, endotoxin contamination of biomaterials is rarely considered, despite its ability to significantly affect the performance of biomaterials and engineered tissues. This review highlights the importance of the immune response to biomaterials and discusses existing challenges and opportunities in the development and standardised assessment of the immune response to biomaterials, including the importance of endotoxin levels. In addition, the properties of biomaterials that impact the host immune response and the exploitation of immunomodulatory biomaterials in regenerative medicine are explored. Finally, a standardised in vitro pathway of evaluating the immune response to biomaterials (hydrogels) and their regenerative potential is proposed, aiming to ensure safety and consistency, while reducing costs and the use of animals in the biomaterials research for tissue engineering and regenerative medicine. STATEMENT OF SIGNIFICANCE: This review presents a critical analysis of the role of the interactions between the immune system and biomaterials in determining the therapeutic success of biomaterial-based approaches. No such review addressing the lack of understanding of biomaterial-immune system interactions during the developmental and pre-clinical stages of biomaterials, including the impact of the endotoxin levels of biomaterials on the immune response, is published. As there is a lack of in vitro regulations to evaluate the immune response to biomaterials, a standardised in vitro pathway to evaluate the immune response to biomaterials (hydrogels) and their immunomodulatory and regenerative potential for use in tissue engineering/regenerative medicine applications is presented. The aim of the proposed pathway of biomaterial evaluation is to ensure safety and consistency in the biomaterials research community, while reducing costs and animal use (through the concept of the 3R's - reduction, refinement, and replacement of animals).

Adhesive Interfaces toward a Zero-Waste Industry.

This Feature Article evaluates ongoing efforts to adapt adhesives toward the goal of zero-waste living and suggests the most promising future directions. Adhesives are not always considered in zero-waste manufacturing because they represent only a small fraction of a product and offer no additional functionality. However, their presence restricts the reintegration of constituent parts into a circular economy, so a new generation of adhesives is required. Furthermore, their production often leads to harmful pollutants. Here, two main approaches toward addressing these problems are considered: first, the use of natural materials that replace petroleum-based polymers from which conventional adhesives are made and second, the production of dismantlable adhesives capable of debonding on demand with the application of an external stimulus. These approaches, either individually or combined, offer a new paradigm in zero-waste industrial production and consumer applications.

Self-crystallisation, an unexpected property of 45S5 Bioglass®.

Self-crystallisation of 45S5 Bioglass® powder and scaffolds was observed one year after their fabrication. Plate- and acicular-shape crystals, identified as calcium and sodium carbonates, grew at room temperature and atmospheric pressure, without any further treatment.

Immobilization of Molecularly Imprinted Polymer Nanoparticles onto Surfaces Using Different Strategies: Evaluating the Influence of the Functionalized Interface on the Performance of a Thermal Assay for the Detection of the Cardiac Biomarker Troponin I.

We demonstrate that a novel functionalized interface, where molecularly imprinted polymer nanoparticles (nanoMIPs) are attached to screen-printed graphite electrodes (SPEs), can be utilized for the thermal detection of the cardiac biomarker troponin I (cTnI). The ultrasensitive detection of the unique protein cTnI can be utilized for the early diagnosis of myocardial infraction (i.e., heart attacks), resulting in considerably lower patient mortality and morbidity. Our developed platform presents an innovative route to develop accurate, low-cost, and disposable sensors for the diagnosis of cardiovascular diseases, specifically myocardial infraction. A reproducible and advantageous solid-phase approach was utilized to synthesize high-affinity nanoMIPs (average size = 71 nm) for cTnI, which served as synthetic receptors in a thermal sensing platform. To assess the performance and commercial potential of the sensor platform, various approaches were used to immobilize nanoMIPs onto thermocouples or SPEs: dip coating, drop casting, and a covalent approach relying on electrografting with an organic coupling reaction. Characterization of the nanoMIP-functionalized surfaces was performed with electrochemical impedance spectroscopy, atomic force microscopy, and scanning electron microscopy. Measurements from an in-house designed thermal setup revealed that covalent functionalization of nanoMIPs onto SPEs led to the most reproducible sensing capabilities. The proof of application was provided by measuring buffered solutions spiked with cTnI, which demonstrated that through monitoring changes in heat transfer at the solid-liquid interface, we can measure concentrations as low as 10 pg L-1, resulting in the most sensitive test of this type. Furthermore, preliminary data are presented for a prototype platform, which can detect cTnI with shorter measurement times and smaller sample volumes. The excellent sensor performance, versatility of the nanoMIPs, and reproducible and low-cost nature of the SPEs demonstrate that this sensor platform technology has a clear commercial route with high potential to contribute to sustainable healthcare.

History, versatility and future prospects of oscillatory carbonylation reactions of alkynes.

The paper looks back at three decades of oscillatory carbonylation reactions, summarises core findings and shares perspectives, with particular emphasis on applications. Oscillatory carbonylation reactions of alkynes display remarkable versatility in terms of substrates, catalysts and solvents. Furthermore, in addition to oscillations in pH and redox potential, these organic chemical oscillators can yield oscillations in turbidity and release heat from the reaction in a pulsatile manner. Recent research developments shift attention from small molecule substrates (e.g. phenylacetylene) and small molecule catalysts (e.g. palladium(ii) iodide), to oscillatory carbonylation reactions using polymeric substrates (e.g. PEGylated alkynes) and polymeric catalysts (e.g. imine-functionalized chitosan-palladium) and use of these polymeric building blocks to develop oscillatory (pulsatile) materials fit for pulsatile drug release and other applications.

Chitosan based polymer/bioglass composites for tissue engineering applications.

Composite scaffolds formed from polymers and bioglasses have been widely explored for applications in regenerative medicine as they have suitable organic/inorganic structures and properties similar to human hard tissue. Yet, these materials have only been used for non-load-bearing or low load-bearing purposes as they have limited mechanical strength while research is focused on improving their properties. One method of improving mechanical strength is by covalently bonding the organic and inorganic phases. This has been successfully achieved in Class ll hybrids which have covalent bonding between polymers and bioglasses. As well as improving mechanical strength, the chemical connection of the two phases results in simultaneous degradation. The currently available composite scaffolds use collagen for the polymer phase which can cause allergic reactions and transmit pathogens. An alternative natural polymer is chitosan which has been used to create scaffolds with bioglass avoiding the issues arising from collagen. Additionally, using cross-linking agents has been shown to strengthen chitosan hydrogels improving their mechanical properties. A promising natural cross-linker is genipin which has lower toxicity than other cross-linking agents while producing hydrogels with improved mechanical properties compared to pure chitosan. In this paper we offer an overview of requirements, structures and currently available composite scaffolds for tissue engineering applications. We discuss the limitations of the currently available materials and consider the potential of covalently bonded hybrids particularly in relation to chitosan-based materials and the added benefits of genipin cross-linking.

Stoichiometric network analysis of a reaction system with conservation constraints.

Stoichiometric Network Analysis (SNA) is a powerful method that can be used to examine instabilities in modelling a broad range of reaction systems without knowing the explicit values of reaction rate constants. Due to a lack of understanding, SNA is rarely used and its full potential is not yet fulfilled. Using the oscillatory carbonylation of a polymeric substrate [poly(ethylene glycol)methyl ether acetylene] as a case study, in this work, we consider two mathematical methods for the application of SNA to the reaction models when conservation constraints between species have an important role. The first method takes conservation constraints into account and uses only independent intermediate species, while the second method applies to the full set of intermediate species, without the separation of independent and dependent variables. Both methods are used for examination of steady state stability by means of a characteristic polynomial and related Jacobian matrix. It was shown that both methods give the same results. Therefore, as the second method is simpler, we suggest it as a more straightforward method for the applications.

From small molecules to polymeric catalysts in the oscillatory carbonylation reaction: multiple effects of adding HI.

The oscillatory palladium-catalysed carbonylation reaction opens new horizons for applications in smart materials due to the versatility of its conditions and substrates, as well as the adjustability of amplitude and period of pH oscillations. A variety of viable substrates have been demonstrated, including polymeric alkyne-terminated substrates. However, so far, there have not been any reports of polymer-based palladium catalysts in oscillatory mode. In this paper, we demonstrate pH oscillations in various systems, using commercially available palladium acetate, a triphenylphosphine palladium acetate complex and a polymer-bound palladium catalyst. While palladium acetate was able to generate oscillations under the conditions already established in our previous research on PdI2-catalysed oscillators, the other two catalysts needed the addition of HI to induce oscillations. HI forced an initial pH drop, bringing pH into the range where oscillations generally occur. Addition of HI had a significant effect on all catalysts, modifying the amplitude and period of oscillations, oscillation mode, as well as starting material conversion and product distribution.

Stability and Synergistic Effect of Polyaniline/TiO2 Photocatalysts in Degradation of Azo Dye in Wastewater.

The polyaniline/TiO2 (PANI/TiO2) composite photocatalysts were prepared by the in situ chemical oxidation of aniline (An) in the presence of TiO2 particles. For this purpose, photocatalysts with different amounts of PANI polymer were prepared and analysed. Fourier-transform infrared (FT-IR) spectroscopy and thermogravimetric (TG) analysis indicated successful synthesis of the PANI polymer and its conductivity was also determined. The micrographs of field emission scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM) were used to explain the impact of the aniline amount on the aggregation process during the synthesis of the composites. The smallest size of aggregates was obtained for the photocatalysts with 15% of PANI (15PANI/TiO2) due to the formation of homogenous PANI. The photocatalytic activity of studied PANI/TiO2 photocatalysts was validated by monitoring the discoloration and mineralization of Reactive Red azo dye (RR45) in wastewater. The 15PANI/TiO2 sample presented the highest photocatalytic efficiency under ultraviolet A (UVA) irradiation, in comparison to pure TiO2. This was explained by the formation of uniformly dispersed PANI on the TiO2 particles, which was responsible for the synergistic PANI-TiO2 effect.

The Effect of Temperature on Selectivity in the Oscillatory Mode of the Phenylacetylene Oxidative Carbonylation Reaction.

Reaction temperature plays a major role in product selectivity in the oscillatory mode of the palladium-catalyzed phenylacetylene oxidative carbonylation reaction. At 40 °C, dimethyl (2Z)-2-phenyl-2-butenedioate is the major product whereas at 0 °C the major product is 5,5-dimethoxy-3-phenyl-2(5H)-furanone. The occurrence of oscillations in pH coincides with an increase in the rate of phenylacetylene consumption and associated product formation. Experiments were performed isothermally in a reaction calorimeter to correlate reactant consumption and product formation with the occurrence of pH oscillations and the heat released by the reaction. An increase in the size of the pH drop in a single oscillation correlates with an increase in energy, indicating that this section of a single oscillation relates to reactant consumption. Based on these observations, a reaction pathway responsible for product formation is provided.

Fluorescence Imaging in Genipin Crosslinked Chitosan⁻Poly(vinyl pyrrolidone) Hydrogels.

Recent research has identified genipin as a promising natural crosslinking agent for biocompatible hydrogels as genipin is significantly less cytotoxic than current synthetic crosslinking agents, such as glutaraldehyde. Conveniently, fluorophores can be produced when genipin crosslinks. In this study, fluorescence intensity measurements of genipin crosslinked chitosan-poly(vinyl pyrrolidone) hydrogels have been explored as a dynamic, in situ method for tracing sol-gel transition. These pH-responsive smart materials have a future in medical applications, in particular in tissue engineering and drug delivery, where methods to follow the process in situ and in real-time are crucial for future advancement. Samples were prepared using deionised water, pH 4, and pH 10 solutions, and studied at 24 and 37 °C over a 24 h period. Both temperature and pH have been found to affect sol-gel transition in the hydrogels studied. The transition from acidic (pH 4) to basic (pH 10) solution resulted in reduced fluorescence intensity suggesting that, under more basic conditions, genipin molecules self-polymerise, reducing the number of molecules available for reaction with the amino groups of chitosan. Three-dimensional representations of the fluorescence present in a hydrogel sample have also been produced from the data, enabling the visualisation of variation in fluorescence with time at the surface of the hydrogel.

Oscillatory carbonylation using alkyne-functionalised poly(ethylene glycol).

In this study palladium-catalysed oscillatory carbonylation has been achieved using mono alkyne-terminated poly(ethylene glycol) methyl ether substrates. Reproducible, synchronised oscillations in pH and solution turbidity have been recorded over several days. A reaction network accounting for the observed phenomena has been proposed.

The influence of reaction temperature on the oscillatory behaviour in the palladium-catalysed phenylacetylene oxidative carbonylation reaction.

This paper reports the influence of reaction temperature on the occurrence and characteristics of pH oscillations that are observed during the palladium-catalysed phenylacetylene oxidative carbonylation reaction in a catalytic system (PdI2, KI, air, NaOAc) in methanol. Isothermal experiments were performed over the temperature range 10-50 degrees C. The experiments demonstrate that oscillations occur in the range 10-40 degrees C and that a decrease in reaction temperature results in an increase in the period and amplitude of the pH oscillations. Furthermore, it is observed that during oscillations at any specific temperature, the time taken for pH to increase from a minimum to a maximum value varies with respect to reaction time. However, the time required for the pH to fall from maximum to new minimum is approximately constant with respect to the reaction time and is a function of the reaction temperature.

The influence of oscillations on product selectivity during the palladium-catalysed phenylacetylene oxidative carbonylation reaction.

This paper reports on the influence of oscillations on product selectivity as well as the dynamics of product formation during the palladium-catalysed phenylacetylene oxidative carbonylation reaction in a catalytic system (PdI2, KI, Air, NaOAc in methanol). The occurrence of the pH oscillations is related to PdI2 granularity and the initial pH drop after phenylacetylene addition. To achieve pH and reaction exotherm oscillations regulation of the amount of PdI2 is required, ensuring that the initial pH does not fall significantly below 1 after phenylacetylene addition. Experiments in both oscillatory and non-oscillatory pH regimes were performed in an HEL SIMULAR reaction calorimeter with the concentration-time profiles measured using a GC-MS. It is demonstrated that when operating in an oscillatory pH regime product formation may be suppressed until oscillations occur after which there is a steep increase in the formation of Z-2-phenyl-but-2-enedioic acid dimethyl ester. When operating in non-oscillatory pH mode the products are formed steadily over time with the main products being Z-2-phenyl-but-2-enedioic acid dimethyl ester, 2-phenyl-acrylic acid methyl ester and E-3-phenyl-acrylic acid methyl ester.