RESUMEN
Microalgae have emerged as a promising source of biomass to produce renewable biofuels due to their ability to synthesize high-energy density compounds of commercial interest. This study proposes an approach for pilot-scale oil extraction, purification by fractional distillation, hydrocarbon characterization by gas chromatography coupled to mass spectrometry (GC-MS), evaluation of physicochemical parameters of the produced hydrocarbons, preliminary cost analysis, and challenges and future opportunities for green diesel on a commercial scale. Here, the microalgae Tetradesmus obliquus was cultivated in 12 m³ photobioreactors using biodigested swine waste as a culture medium. The resulting biomass was subjected to drying and harvesting, followed by oil extraction using a hot solvent extraction method, followed by distillation to purify the compounds. Three different extraction and distillation experiments were conducted, each using different solvent combinations. The results obtained revealed that extraction with a solvent blend, composed of hexane and ethanol, provided more significant yields compared to extraction with pure hexane. GC-MS analysis showed the presence of alkanes and alkenes in the oil samples, and the proportion of solvent used in the extraction directly influenced the production of alkanes. Additionally, specific hydrocarbons such as 4-methyl-1-decene, 8-heptadecene, 1-pentadecene, 9-heneicosene, and 2-dodecene were identified. The evaluation of the physicochemical parameters demonstrated that the calorific value of the distilled oil samples is within the range of typical values for petroleum diesel. However, it was observed that the distilled oil samples had higher sulfur content compared to conventional diesel. Regarding the cost analysis, it was found that it varies depending on the experimental conditions. In particular, the process using a solvent mixture of 70% hexane and 30% ethanol proved to be more economical than the others, since it extracted a greater quantity of oil with a lower initial biomass requirement. In summary, this microalgae-derived hydrocarbon production process is promising and offers insights for compound purification and future biofuel applications.
RESUMEN
Thermoelectric devices are both solid-state heat pumps and energy generators. Having a reversible process without moving parts is of high importance for applications in remote locations or under extreme conditions. Yet, most thermoelectric devices have a rather limited energy conversion efficiency due to the natural competition between high electrical conductivity and low thermal conductivity, both being essential conditions for achieving a high energy conversion efficiency. Heavy-fermion compounds YbT2Zn20 (T = Co, Rh, Ir) have been reported to be potential candidate materials for thermoelectric applications at low temperatures. Motivated by this result, we applied chemical substitution studies on the transition metal site in order to optimize the charge carrier concentration as well as promote more efficient phonon scatterings. Here, we present the latest investigation on the Ni-doped specimens YbCo2-xNixZn20, where enhanced thermoelectric figure of merit values have been obtained.
RESUMEN
Mound structures that soil termites build have diverse morphologies. Previous observational studies documented that mounds are built to provide regulated environments for the termites that live within them and their structures are formed in ways to support this purpose under the influence of the mounds' immediate environment. The objective of this study is to provide a methodology and a predictive computational model to investigate the reason behind the different but systematic shapes of termite mounds, considering all the relevant forces imposed on them and their thermoregulatory and gas-exchange functions. The gas-exchange function accounts for the capacity of the mound to diffuse metabolic gases generated in the mound's underground nest, while the thermoregulatory function satisfies the connection between the underground nest and deep ground temperatures. The proposed predictive model is based on the principles of heat transfer and thermodynamics and allows optimized mechanically stable structures to freely emerge. The results indicate that, while the model is free to generate any mechanically stable structure, under the relevant environmental and metabolic conditions, it produces structures with forms and geometrical characteristics similar to those of natural mounds. Investigation of the connection between the local environment and the mound shapes indicated that the Sun and wind play an important role in the mound structural form. Mounds exposed to stronger solar irradiance exhibit cone-shaped structures that are pointed towards the Sun, while shaded mounds are observed to be vertical domes. The local wind is observed to affect the external shape of the mound by preventing them to grow tall while controlling the features of the internal structure. By investigating the similarities between structures in different regions (i.e., India, Namibia, and Brazil), it is revealed that, unlike mounds with a strong need for gas-exchange, mounds with a significant demand for thermoregulation exhibit deeper nests, thicker external walls, and well-defined cone- (as opposed to the dome-) shaped structures. Overall, the form of termite mounds is strongly correlated to both regulatory functions and local environments, and the resulting mound shape arises as a combination of these factors.
