Designing a Simple Electrochemical Genosensor for the Detection of Urinary PCA3, a Prostate Cancer Biomarker.

This study investigates the feasibility of a simple electrochemical detection of Prostate Cancer Antigen 3 (PCA3) fragments extracted from patients' urine, using a thiolated single-strand DNA probe immobilized on a gold surface without using a redox probe. To enhance the PCA3 recognition process, we conducted a comparative analysis of the hybridization location using two thiolated DNA probes: Probe 1 targets the first 40 bases, while Probe 2 targets the fragment from bases 47 to 86. Hybridization with PCA3 followed, using square wave voltammetry. The limit of detection of the designed genosenors were of the order of (2.2 ng/mL), and (1.6 ng/mL) for Probes 1 and 2, respectively, and the subsequent sensitivities were of the order of (0.09 ± 0.01) µA-1 · µg-1 · mL and (0.10 ± 0.01) µA-1 · µg-1 · mL. Specificity tests were then conducted with the sensor functionalized with Probe 2, as it presents better analytical performances. The electrochemical results indicate that the designed sensor can clearly discriminate a complementary target from a non-complementary one. A further modeling of the calibration curves with the Power Law/Hill model indicates that the dissociation constant increases by one order of magnitude, confirming the ability of the designed sensor to perfectly discriminate complementary targets from non-complementary ones.

Novel sensitive immunosensor for the selective detection of Engrailed 2 urinary prostate cancer biomarker.

Engrailed 2 (EN2) is a homeodomain-containing transcription factor expressed in prostate cancer (PCa) cell lines and is secreted into the urines. It is nowadays considered as a promising non-invasive biomarker for PCa early diagnosis. Herein, we report the design of an electrochemical immunosensor for EN2 detection. The biosensor fabrication involved a covalent immobilization of anti-EN2 antibodies onto a poly para amino benzoic acid (PABA) film electropolymerized on a gold electrode. Square wave voltammetry was investigated for EN2 detection in a phosphate buffer solution in a concentration range of 10-5 ng/mL to 1 µg/mL. The limit of detection of the designed sensor was equal to 10-5 ng/mL and the sensitivity was of order of (29 ± 2) µL/ng. The dissociation constant Kd of the "complex" EN2/anti-EN2, estimated from a Hill model, was of order of (0.9 ± 0.2) fM. Experimental results revealed that the immunosensor enabled selective detection of EN2 in a mixture of three proteins which can be found in men' urine: human serum albumin (HSA), prostate-specific antigen (PSA) and immunoglobulin G (IgG). Tests in artificial urine, with an ionic strength of 0.18 M, have been done and results were found comparable to those obtained in PBS (0.16 M). These encouraging results show a potentially promising future for the development of an electrochemical biosensor for robust and accurate urinary biomarkers detection.

Contribution to the Understanding of the Interaction between a Polydopamine Molecular Imprint and a Protein Model: Ionic Strength and pH Effect Investigation.

Several studies were devoted to the design of molecularly imprinted polymer (MIP)-based sensors for the detection of a given protein. Here, we bring elements that could contribute to the understanding of the interaction mechanism involved in the recognition of a protein by an imprint. For this purpose, a polydopamine (PDA)-MIP was designed for bovine serum albumin (BSA) recognition. Prior to BSA grafting, the gold surfaces were functionalized with mixed self-assembled monolayers of (MUDA)/(MHOH) (1/9, v/v). The MIP was then elaborated by dopamine electropolymerization and further extraction of BSA templates by incubating the electrode in proteinase K solution. Three complementary techniques, electrochemistry, zetametry, and Fourier-transform infrared spectrometry, were used to investigate pH and ionic strength effects on a MIP's design and the further recognition process of the analytes by the imprints. Several MIPs were thus designed in acidic, neutral, and basic media and at various ionic strength values. Results indicate that the most appropriate conditions, to achieve a successful MIPs, were an ionic strength of 167 mM and a pH of 7.4. Sensitivity and dissociation constant of the designed sensor were of order of (3.36 ± 0.13) µA·cm-2·mg-1·mL and (8.56 ± 6.09) × 10-11 mg/mL, respectively.

Legionella pneumophila sg1-sensing signal enhancement using a novel electrochemical immunosensor in dynamic detection mode.

This work presents a comparison between static and dynamic modes of biosensing using a novel microfluidic assay for continuous and quantitative detection of Legionella pneumophila sg1 in artificial water samples. A self-assembled monolayer of 16-amino-1-hexadecanethiol (16-AHT) was covalently linked to a gold substrate, and the resulting modified surface was used to immobilize an anti-Legionella pneumophila monoclonal antibody (mAb). The modified surfaces formed during the biosensor functionalization steps were characterized using electrochemical measurements and microscopic imaging techniques. Under static conditions, the biosensor exhibited a wide linear response range from 10 to 108 CFU/mL and a detection limit of 10 CFU/mL. Using a microfluidic system, the biosensor responses exhibited a linear relationship for low bacterial concentrations ranging from 10 to 103 CFU/mL under dynamic conditions and an enhancement of sensing signals by a factor of 4.5 compared to the sensing signals obtained under static conditions with the same biosensor for the detection of Legionella cells in artificially contaminated samples.

Computational approach and electrochemical measurements for protein detection with MIP-based sensor.

Rapid and accurate detection of proteins in biological fluids is increasingly required in the biomedical environment. Actually, it is performed with conventional techniques, which are generally run by robotized platforms at centralized laboratories. In this work, molecular dynamics calculations and an experimental procedure were conducted to set up electrochemical sensors based on polypyrrol (PPy) molecular imprinted polymers (MIP) for proteins detection. Here, prostate-specific antigen (PSA) was selected as a template model. Computational calculations indicate that for any PPy conformation and any amino-acid location in the protein, PSA molecules remain strongly inserted in the PPy polymer without biological alterations. One from possible orientations, appeared to be most probable as it presents the lowest absorption energy (-363 kcal mol-1) and largest contact area (4034.1 Å2). The device was then elaborated by in situ electropolymerization of PPy films. MIP's thickness and extraction duration were optimized by chronoamperometry. Square wave voltammetry technique was investigated for PSA detection in standard solution in the concentration range of 3x10 -8 ng.ml-1- 300 ng ml-1. According to the Hill equation, the equilibrium dissociation constant Kdbetween PSA and its imprint was estimated at Kd = (1.02 ±â€¯0.54) × 10-14 M, confirming the strong binding between the designed MIP and the protein as predicted by the computational study. PSA concentration values directly measured in 35 human serum samples were found closely correlated to those measured by the ELISA technique. The promising fast and low-cost sensor might be used successfully for proteins detection at low concentrations with high selectivity and reproducibility.

Electrochemical and optical investigation of dental pulp stem cell adhesion on modified porous silicon scaffolds.

Extensive use of porous silicon (PSi) for tissue engineering is due to its convenient properties as it is both nontoxic and bioresorbable. Moreover, PSi surface modification is an important step to enhance cell adhesion and proliferation. In this work, a combination of optical and electrochemical studies is performed to elaborate a suitable PSi multilayer substrate for cell culture. For this study, we modified PSi surface by silanization and antibody grafting (APTES-anti STRO1), the 12-mer specific peptide to silicon p + type coating and the peptide modified with the antibody recognition sequence. Electrochemical characterization of PSi multilayers is performed to investigate its electrical behavior, determine the optimal measuring conditions and reveal the most stable PSi surfaces. Then, the behavior of dental pulp stem cells (DPSC) was investigated on various modified PSi surfaces. An electrochemical method was applied for the first time monitoring the electrical behavior of stem cell adhesion. The cells electrochemical behavior depends on the nature of the surface coating and the peptide-anti STRO1 improved adhesion and cell spreading onto the PSi surface compared to bare surface and the one coated with the peptide. Fluorescent microscopy revealed that all surface modification methods enhance cell adhesion compared to the bare PSi surface. An increased cell number is observed on APTES-anti STRO1, peptide and peptide-anti STRO1 coated PSi. The peptide-anti STRO1 provided the best cell proliferation results suggesting the improved accessibility of the recognition fragment of the antibody anti-STRO1.

Detection of plasma MMP-9 within minutes. Unveiling some of the clues to develop fast and simple electrochemical magneto-immunosensors.

Magnetic beads (MB) have been extensively used to produce sensitive and efficient electrochemical magneto-immunosensors. However, MB effective handling requires training, and MB washing after each incubation step is time consuming and contributes to raise result variability. Consequently, most of the electrochemical magneto-immunosensors reported to date, which entailed relatively long and complex multi-step procedures, would be difficult to carry out at point-of-care (POC) settings or by laypersons. For this reason, here we targeted the development of a simplified detection path, which is fast and simple enough to be operated at a POC setting, sufficiently efficient to provide analyte quantitation comparable to classical diagnostic methods, and dependent on minimal technical requirements to facilitate method global exploitation. As a proof-of-concept, we optimized an extremely simple, fast and efficient electrochemical magneto-immunosensor for detection of matrix metalloproteinase 9 (MMP-9). To accomplish this, we optimized MB immunomodification, produced an immunomodified Poly-HRP signal amplifier, developed a single-step magneto-immunoassay, and optimized electrochemical detection using a multiplexed magnetic holder and a ready-to-use commercial substrate solution. The sensor was finally calibrated by detecting MMP-9 in clinical samples. This electrochemical magneto-immunosensor detected MMP-9 in just 12-15 min, displaying linear response between 0.03 and 2 ng mL-1 of MMP-9, limits of detection (LOD) and quantification (LOQ) of 13 pg mL-1 and 70 pg mL-1, respectively, %CV< 6%, and accurate quantification of MMP-9 in patient plasma samples. These results were comparable to those afforded by a 5-h reference ELISA that used the same antibodies, confirming the applicability of our simplified method.

Using magnetic beads and signal amplifiers to produce short and simple immunoassays: Application to MMP-9 detection in plasma samples.

Magnetic beads (MB) and signal amplifiers, such as horseradish peroxidase polymers (poly-HRP), have been used before for the production of highly sensitive immunoassays. However, most of the examples reported previously entailed long and tedious multi-step procedures, which were not necessarily shorter or simpler than classical paths such as Enzyme-Linked Immunosorbent Assay (ELISA). Here, instead of exploiting the combination of MB and poly-HRP to ameliorate sensitivity, we show that they conform a powerful tool that can be used to shorten the incubation times, which allows optimizing extremely simple, fast and efficient immunoassays with minimal technical requirements. In order to do so, here we used the highly sensitive and specific pair of antibodies of a commercial ELISA kit to optimize a magneto-ELISA for the detection of matrix metallopeptidase 9 (MMP-9). Three signal amplifiers were then tested and the best performing one was implemented in the magneto-assay to shorten the incubation times and improve assay performance. As we show, the shortened magneto-assay could be carried out in about 35 min, which included two 5-min incubations, washing, and incubation with enzyme substrate for 20 min before colorimetric detection. Moreover, the quantification of MMP-9 provided by the shortened assay in 12 plasma samples collected from patients was comparable to that generated by the 5-h ELISA, which was 8.5 times longer.

Highly Selective Polypyrrole MIP-Based Gravimetric and Electrochemical Sensors for Picomolar Detection of Glyphosate.

There is a global debate and concern about the use of glyphosate (Gly) as an herbicide. New toxicological studies will determine its use in the future under new strict conditions or its replacement by alternative synthetic or natural herbicides. In this context, we designed biomimetic polymer sensing layers for the selective molecular recognition of Gly. Towards this end, complementary surface acoustic wave (SAW) and electrochemical sensors were functionalized with polypyrrole (PPy)-imprinted polymer for the selective detection of Gly. Their corresponding limits of detection were on the order of 1 pM, which are among the lowest values ever reported in literature. The relevant dissociation constants between PPy and Gly were estimated at [Kd1 = (0.7 ± 0.3) pM and Kd2 = (1.6 ± 1.4) µM] and [Kd1 = (2.4 ± 0.9) pM and Kd2 = (0.3 ± 0.1) µM] for electrochemical and gravimetric measurements, respectively. Quantum chemical calculations permitted to estimate the interaction energy between Gly and PPy film: ΔE = -145 kJ/mol. Selectivity and competitivity tests were investigated with the most common pesticides. This work conclusively shows that gravimetric and electrochemical results indicate that both MIP-based sensors are perfectly able to detect and distinguish glyphosate without any ambiguity.

Ultrasensitive Electrochemical Sensors for PSA Detection: Related Surface Functionalization Strategies.

Prostate cancer is the most common male cancer in the world. The diagnosis, staging, prognosis and monitoring are usually done with Prostate Specific Antigen (PSA). Biosensors are emerging as a novel analytical technology for PSA detection. They provide several advantages for clinical applications and will benefit clinicians, patients and forensic workers in the future. Among them, electrochemical immunosensors have gained growing interests. Hence, their sensitivity is often improved by modifying them with nanoparticles especially iron oxide (IONP). Functionalized IONP attracted much attention in the fabrication of biosensing systems, due to their multiple properties, such as biocompatibility and signal amplification, and their ability to bind covalently to antibodies via their functional groups. In the present study, two electrochemical immunosensors were investigated for PSA detection. The first one was functionalized with 3- glycidoxypropyltrimethoxysilane self-assembled monolayer, while the second one was based on iron oxide nanoparticles functionalized with 3-aminopropyltriethoxysilane. Square wave voltammetry (SWV) has been investigated to follow-up the PSA detection in a phosphate buffer solution, in an artificial serum and in a human serum. The limit of detection (LOD) of both immunosensors was found of order of 10 fg/ml. When estimated in human serum this value increases up to 50 pg/ml.

Impact of chlorhexidine digluconate and temperature on curli production in Escherichia coli-consequence on its adhesion ability.

Chlorhexidine-Digluconate (CHX-Dg) is a biocide widely used as disinfectant or antiseptic in clinical and domestic fields. It is often found in the formulation of solutions to treat superficial wounds. Nevertheless, few studies have focused on its effects on Escherichia coli while this bacterium is commonly involved in mixed infections. Therefore, the impact of CHX-Dg and temperature on E. coli was investigated; particularly the curli production. In accordance with bibliographic data, the curli production decreased when the temperature of the culture was shift from 30 °C to 37 °C. The bacterial adhesion to abiotic surfaces was also reduced. Surprisingly, the curli production at 37 °C was maintained in presence of antiseptic and the bacterial adhesion was improved at a very low concentration (1 µg ml-1) of CHX-Dg. Complementary investigations with a cpxR mutant demonstrated that the CpxA/R-TCS (Two-Component System) is involved in the temperature-dependent control of the curli expression. Indeed, the curli production was not altered by the growth temperature in the mutant. Otherwise, no relationship between CHX-Dg and the Cpx-TCS was shown. A subsequent proteomic investigation revealed the alteration of the production of 44 periplasmic and outer membrane proteins in presence of CHX-Dg. These proteins are involved in the transport of small molecules, the envelope integrity, the stress response as well as the protein folding.

Application of APTES-Anti-E-cadherin film for early cancer monitoring.

Cancer staging is a way to classify cancer according to the extent of the disease in the body. The stage is usually determined by several factors such as the location of the primary tumor, the tumor size, the degree of spread in the surrounding tissues, etc. The study of E-cadherin (EC) expression on cancerous cells of patients has revealed variations in the molecular expression patterns of primary tumors and metastatic tumors. The detection of these cells requires a long procedure involving conventional techniques, thus, the requirement for development of new rapid devices that permit direct and highly sensitive detection stimulates the sensing field progress. Here, we explore if E-cadherin could be used as a biomarker to bind and detect epithelial cancer cells. Hence, the sensitive and specific detection of E-cadherin expressed on epithelial cells is approached by immobilizing anti-E-cadherin antibody (AEC) onto aminosilanized indium-tin oxide (ITO) surface. The immunosensing surfaces have been characterized by electrochemical measurements, wettability and confocal microscopy and their performance has been assessed in the presence of cancer cell lines. Under optimal conditions, the resulting immunosensor displayed a selective detection of E-cadherin expressing cells, which could be detected either by fluorescence or electrochemical techniques. The developed immunosensing surface could provide a simple tool that can be applied to cancer staging.

AFM, CLSM and EIS characterization of the immobilization of antibodies on indium-tin oxide electrode and their capture of Legionella pneumophila.

The microscopic surface molecular structures and properties of monoclonal anti-Legionella pneumophila antibodies on an indium-tin oxide (ITO) electrode surface were studied to elaborate an electrochemical immunosensor for Legionella pneumophila detection. A monoclonal anti-Legionella pneumophila antibody (MAb) has been immobilized onto an ITO electrode via covalent chemical bonds between antibodies amino-group and the ring of (3-Glycidoxypropyl) trimethoxysilane (GPTMS). The functionalization of the immunosensor was characterized by atomic force microscopy (AFM), water contact angle measurement, cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) in the presence of [Fe(CN)6](3-/4-) as a redox probe. Specific binding of Legionella pneumophila sgp 1 cells onto the antibody-modified ITO electrode was shown by confocal laser scanning microscopy (CLSM) imaging and EIS. AFM images evidenced the dense and relatively homogeneous morphology on the ITO surface. The formation of the complex epoxysilane-antibodies acting as barriers for the electron transfer between the electrode surface and the redox species in the solution induced a significant increase in the charge transfer resistance (Rct) compared to all the electric elements. A linear relationship between the change in charge transfer resistance (ΔRct=Rct after immunoreactions - Rct control) and the logarithmic concentration value of L. pneumophila was observed in the range of 5 × 10(1)-5 × 10(4) CFU mL(-1) with a limit of detection 5 × 10(1)CFU mL(-1). The present study has demonstrated the successful deposition of an anti-L. pneumophila antibodies on an indium-tin oxide surface, opening its subsequent use as immuno-captor for the specific detection of L. pneumophila in environmental samples.

Discriminating DNA mismatches by electrochemical and gravimetric techniques.

A silicon nitride functionalized electrode and a 104 MHz lithium tantalate (LiTaO3) surface acoustic wave (SAW) sensor have been used to investigate target-probe recognition processes. Electrochemical and gravimetric measurements have been considered to monitor hybridization of single base mismatch (SBM) in synthetic oligonucleotides and single-nucleotide polymorphisms ApoE in real clinical genotypes. Obvious discrimination of SBM in nucleotides has been shown by both gravimetric and electrochemical techniques, without labeling nor amplification. Investigations on mismatches nature and position have also been considered. For guanine-adenine (GA), guanine-thymine (GT) and guanine-guanine (GG) mismatches, the sensors responses present a dependence upon positions. Considering the capacitance variations and hybridization rates, results showed that gravimetric transduction is more sensitive than electrochemical one. Moreover, the highest value of GT hybridization rate (in the middle position) was found in accordance with the nearest-neighbor model, where the considered configuration appears as the most thermodynamically stable. For the real samples, where the electrochemical transduction, by combining capacitance and flat-band potential measurements, were found more sensitive, the results show that the realized sensor permits an unambiguous discrimination of recognition between fully complementary, non-complementary and single base mismatched targets, and even between the combination of differently matched strands.

Highly hydrophilic surfaces from polyglycidol grafts with dual antifouling and specific protein recognition properties.

Homopolymer grafts from α-tert-butoxy-ω-vinylbenzyl-polyglycidol (PGL) were prepared on gold and stainless steel (SS) substrates modified by 4-benzoyl-phenyl (BP) moieties derived from the electroreduction of the parent salt 4-benzoyl benzene diazonium tetrafluoroborate. The grafted BP aryl groups efficiently served to surface-initiate photopolymerization (SIPP) of PGL. In similar conditions, SIPP of hydroxyethyl methacrylate (HEMA) permitted the production of PHEMA grafts as model surfaces. Water contact angles were found to be 66°, 15°, and 0° for SS-BP, SS-PHEMA, and SS-PPGL, respectively. The spontaneous spreading of water drops on SS-PPGL was invariably observed with 1.5 µL water drops. PPGL thus appears as a superhydrophilic polymer. Resistance to nonspecific adsorption of proteins of PPGL and PHEMA grafts on gold was evaluated by surface plasmon resonance (SPR) using antibovine serum albumin (anti-BSA). The results conclusively show that PPGL-grafts exhibit enhanced resistance to anti-BSA adsorption compared to the well-known hydrophilic PHEMA. PPGL grafts were further modified with BSA through the carbonyldiimidazole activation of the OH groups providing immunosensing surfaces. The so-prepared PPGL-grafted BSA hybrids specifically interacted with anti-BSA in PBS as compared to antimyoglobin. It is clear that the superhydrophilic character of PPGL grafts opens new avenues for biomedical applications where surfaces with dual functionality, namely, specific protein grafting together with resistance to biofouling, are required.

Assessing bacterial adhesion using DLVO and XDLVO theories and the jet impingement technique.

In this study, the adhesion of two bacterial strains (Pseudomonas stutzeri PS, and Staphylococcus epidermidis, SE) to the glass and the indium tin oxide (ITO)-coated glass surfaces was examined qualitatively and quantitatively using the theoretical approaches and the jet impingement technique. A comparison between the DLVO and the extended DLVO (XDLVO) theories showed that the XDLVO predictions of bacterial adhesion and its reversibility are more accurate than DLVO predictions. The adhesion tests revealed that PS bacteria has much better adhesion rate than SE bacteria to both material surfaces, as predicted by XDLVO approach. Also both bacterial strains adhered better to the hydrophobic ITO-coated glass than to the hydrophilic glass surface, as predicted theoretically. Moreover, the microjet impingement technique was used not only to assess the bacterial adhesion strength on both materials, but also to verify the adhesion reversibility. The detachment stress values demonstrated that PS bacterial cells adhered strongly and irreversibly in the primary energy minimum, while SE bacterial cells adhered weakly and reversibly in the secondary energy minimum on both substrata surfaces. Also, the adhesion of both bacterial strains was found better and stronger on the hydrophobic ITO-coated glass surface than on the hydrophilic glass surface.

Surface assembly on biofunctional magnetic nanobeads for the study of protein-ligand interactions.

One of the major challenges of proteomics today is to increase the power potential for the identification of as many proteins as possible and to characterize their interactions with specific free ligands (interactomics) or present on cell walls (cell marker), in order to obtain a global, integrated view of disease processes, cellular processes and networks at the protein level. The work presented here proposes the development of biofunctionalized magnetic nanobeads that might be used for interactomic investigations. The strategy consisted in immobilizing proteins via a non covalent technique that provides greater possibilities for the advent of faster, cheaper and highly miniaturizable protein analysis systems, in particular in situations where the amount of isolated protein is scarce (trace proteins). The advantage of the immobilization technique proposed here over more conventional covalent binding techniques is that it is versatile and universal (not protein specific) thus applicable to a wide range of proteins, in "mild" conditions that are non deleterious to the native structure and bioactivity of the immobilized protein. The feasibility of the technique was investigated using a model protein (streptavidin). The nanobeads were analyzed in size by light diffusion and transmission electronic spectroscopy, and in quantity of immobilized protein using a bioassay developed in the laboratory. Results are promising in that nanobeads exhibited good colloidal stability and surface concentrations in the monolayer range.

Evaluation of endothelial cell adhesion onto different protein/gold electrodes by EIS.

To study cell attachment to biomaterials, several proteins such as fibronectin, collagen IV, heparin, immunoglobulin G, and albumin have been deposited onto polystyrene adsorbed on a self-assembled monolayer (silane or thiol) on glass or gold, respectively. The different steps of this multilayer assembly have been characterized by electrochemical impedance spectroscopy (EIS). These data are compared to those of adhesion rate, viability percentage, and cytoskeleton labeling for a better understanding of the cell adhesion process to each protein. All the proteins are endothelial cell adhering biomolecules but not with the same features. A linear relationship has been established between adhesion rate and resistance of the endothelial cell/protein interface for all negatively charged proteins.

Electrical probing of endothelial cell behaviour on a fibronectin/polystyrene/thiol/gold electrode by Faradaic electrochemical impedance spectroscopy (EIS).

The electrochemical impedance spectroscopy (EIS) technique has been shown to be an effective tool for monitoring endothelial cell behaviour on a multilayer functionalised gold electrode. Polystyrene, a reproducible model substrate, is deposited as a thin layer on a thiol functionalised gold electrode. Fibronectin, a protein promoting endothelial cell adhesion, is then adsorbed on the polystyrene surface. The different steps of this multilayer assembly are characterized by Faradaic impedance. The charge transfer resistance and the capacitance for the total layer are modified at each step according to the electrical properties of each layer. This gives the endothelial cells' electrical state in terms of its resistive and capacitive properties. In this study, the endothelial cell layer presents a specific charge transfer resistance equal to 1.55 kOmega cm(2) with no large defects in the cell layer, and a specific capacitance equal to few microF cm(-2) explained by the existence of pseudopods. These electrical properties are correlated to the endothelial cell viability, adhesion and cytoskeleton organization.