3D-printed custom tray for maxillofacial implant assisted partial denture.

This technique presents a new fabrication workflow for a three-dimensional (3D) printed custom tray, which duplicates the morphology of the treatment denture for maxillofacial prostheses using an intraoral scanner, computer-aided design (CAD) software, and a 3D printer. A 70-year-old man underwent reconstruction of segmental mandibulectomy for mandibular osteoblastoma, followed by implant placement and secondary surgery. During the surgical treatment, a treatment denture was fabricated to restore oral function and determine the morphology of the definitive denture. To create the definitive denture with the same morphology as the treatment denture a custom tray was fabricated with the denture morphology after chairside adjustments. The oral cavity was scanned using an intraoral scanner, and the data acquired were imported into general-purpose CAD software, adjusted, and imported into a 3D printer to produce the custom tray. This was fitted into the patient's mouth without any issues, and closed tray impressions were made with impression caps for the locator attachments on the implant body. The morphology of the treatment denture was replicated in the definitive denture by making a silicon impression of the cameo surface at the fabrication of the cast after impression making. In this technique, the morphology of the treatment denture was transferred accurately to the definitive implant partial denture by leveraging existing digital technology. This method represents a practical approach for partial denture fabrication, including maxillofacial defects with complex denture configurations.

Quantitative analysis of change in bone volume 5 years after sinus floor elevation using plate-shaped bone substitutes: a prospective observational study.

PURPOSE: Tricalcium phosphate (TCP) has osteoconductive ability and reportedly offers similar clinical results as autogenous bone grafts in dental implant treatment. However, few reports quantify temporal changes in augmented bone volume after sinus augmentation. We aimed to establish a three-dimensional (3D) quantification method to assess bone volume after sinus augmentation and to evaluate biocompatibility of the TCP plate. METHODS: Maxillary sinus floor augmentation was performed employing the lateral window technique, and plate-shaped ß-TCP (TCP plate) was used instead of granular bone grafting materials. After lifting the sinus membrane, the TCP plate was inserted and supported by dental implants or micro-screws. The changes in bone volumes in the maxillary sinus before and after surgery were recorded using cone-beam computed tomography, saved as Digital Imaging and Communications in Medicine-formatted files, and transformed to Standard Triangle Language (STL)-formatted files. Pre- and post-operative STL data of bone volume were superimposed, and the augmented bone volume was calculated. Moreover, changes in bone volumes, TCP plate resorption rates, and bone heights surrounding the implants were three dimensionally quantified. RESULTS: Fifteen implants in nine subjects were included in this study. TCP plates secured long-term space making, with results similar to those of granular bone substitutes. Newly formed bone was identified around the implant without bone graft material. TCP plate was absorbed and gradually disappeared. CONCLUSIONS: A novel 3D quantification method was established to evaluate changes in bone volume. Clinical application of TCP plate in sinus augmentation could be a better procedure in terms of prognosis and safety.

Accuracy of optical interocclusal registration using an intraoral scanner.

PURPOSE: This study aimed to clarify the effect of occlusal force on appropriate optical interocclusal registration in clinical practice, considering periodontal ligament and jawbone deformation. METHODS: Forty participants with natural, healthy dentition were enrolled (19 men and 21 women; mean age, 27.7 ± 2.0 years). A TRIOS3 intraoral scanner was used to scan the right lateral first premolar to the second molar areas of the upper and lower jaws. During scanning for interocclusal registration, participants were instructed to "bite normally," "bite lightly," and "bite strongly" to obtain data for the three occlusal patterns. The standard triangulated language (STL) data for each occlusion condition were superimposed using the appropriate software, following which the tooth displacement was calculated. The conventional method was also used to record the occlusal contact area for a silicone model using a dental contact analyzer. RESULTS: Tooth displacement was significantly lower for the strong-bite condition than for the weak-bite condition (0.018 mm vs. 0.028 mm, P<0.05). As the occlusal force increased, the occlusal contact area also increased, and significant differences were observed among the different occlusal conditions (P<0.05). CONCLUSIONS: Occlusal contact area changed depending on the bite force when using the silicone impression or optical intraoral scanning methods. Moreover, using optical impression methods in "strong bite force" may reduce the deviation and allow for stable interocclusal registration.

A review of the recent literature on maxillary overdenture with dental implants.

The recent literature on maxillary implant overdenture (IOD) was reviewed in order to clarify its predictability and establish treatment guidelines. Electronic searches were performed using PubMed, and articles about maxillary IOD written after 1990 were reviewed, focusing on the following items: I. implant survival rate, II. maxillary IOD survival rate, III. number of implants, IV. attachment type, V. follow-up period, VI. implant system, and VII. opposing dentition. The review revealed an implant survival rate of 61-100% and an overdenture survival rate of 72.4-100%. The attachments used included bars, balls, locators, and telescope crowns. The minimum and maximum observation periods were 12 months and 120 months, respectively, and the number of implants used for supporting IOD ranged from 2 to 8. At present, there is no strong evidence to indicate that maxillary IOD is clearly superior for all the items examined. However, the existing data indicate that maxillary IOD has almost the same therapeutic effect as fixed implant superstructures, and is a treatment option that can be actively adopted for patients in whom fixed superstructures cannot be applied for various reasons.

Surface attrition of zirconia and hybrid composite resin superstructure during implant therapy.

PURPOSE: The purpose of this study was to examine morphological changes in the superstructure of implants in relation to the degree of attrition of the implant superstructure and its antagonists. METHODS: Thirty-three patients participated. The implant superstructures of the first molar and its antagonists were scanned with an intraoral scanner every 3 months. The amount of attrition was calculated in relation to the various materials used for the superstructure, and differences were analyzed statistically (P < 0.05). RESULTS: Attrition of the implant superstructure was 110 ± 30 µm for monolithic zirconia and 105 ± 27 µm for resin-veneered metal after 12 months. No statistically significant difference was found between the two groups. In contrast, attrition of the antagonists was 75 ± 25 µm for zirconia and 105 ± 20 µm for resin-veneered metal after 12 months. A statistically significant difference in the attrition levels between the two groups was observed after 9 and 12 months. CONCLUSION: During the 12-month observation period, there was no difference in superstructure attrition between zirconia and resin-veneered metal. Attrition of the antagonists was higher for hybrid composite resin-veneered metal than for zirconia, suggesting that surface roughness affected the degree of attrition.

Simple Duplication Technique of Complete Denture Using an Intraoral Scanner.

Various techniques have been applied to the fabrication of duplicate dentures. In this new method, after scanning the cameo and intaglio surfaces of the complete denture using an intraoral scanner, the two images were superimposed on the interocclusal image. The linear gap between cameo and intaglio surfaces was filled using free downloadable CAD software. The superimposed image was subsequently used as data for fabricating the duplicate complete denture with a 3D printer. Using the intraoral scanner, duplication of complete dentures could be performed without needing any complicated processes, laboratory scanners, or advanced CAD software.