Li Dynamics in Mixed Ionic-Electronic Conducting Interlayer of All-Solid-State Li-metal Batteries.

Lithium-metal (Li0) anodes potentially enable all-solid-state batteries with high energy density. However, it shows incompatibility with sulfide solid-state electrolytes (SEs). One strategy is introducing an interlayer, generally made of a mixed ionic-electronic conductor (MIEC). Yet, how Li behaves within MIEC remains unknown. Herein, we investigated the Li dynamics in a graphite interlayer, a typical MIEC, by using operando neutron imaging and Raman spectroscopy. This study revealed that intercalation-extrusion-dominated mechanochemical reactions during cell assembly transform the graphite into a Li-graphite interlayer consisting of SE, Li0, and graphite-intercalation compounds. During charging, Li+ preferentially deposited at the Li-graphite|SE interface. Upon further plating, Li0-dendrites formed, inducing short circuits and the reverse migration of Li0. Modeling indicates the interface has the lowest nucleation barrier, governing lithium transport paths. Our study elucidates intricate mechano-chemo-electrochemical processes in mixed conducting interlayers. The behavior of Li+ and Li0 in the interlayer is governed by multiple competing factors.

Review on Hybrid Reinforced Polymer Matrix Composites with Nanocellulose, Nanomaterials, and Other Fibers.

The use of composite materials has seen many new innovations for a large variety of applications. The area of reinforcement in composites is also rapidly evolving with many new discoveries, including the use of hybrid fibers, sustainable materials, and nanocellulose. In this review, studies on hybrid fiber reinforcement, the use of nanocellulose, the use of nanocellulose in hybrid forms, the use of nanocellulose with other nanomaterials, the applications of these materials, and finally, the challenges and opportunities (including safety issues) of their use are thoroughly discussed. This review will point out new prospects for the composite materials world, enabling the use of nano- and micron-sized materials together and creating value-added products at the industrial scale. Furthermore, the use of hybrid structures consisting of two different nano-materials creates many novel solutions for applications in electronics and sensors.

Amphipathic Binder Integrating Ultrathin and Highly Ion-Conductive Sulfide Membrane for Cell-Level High-Energy-Density All-Solid-State Batteries.

Current sulfide solid-state electrolyte (SE) membranes utilized in all-solid-state lithium batteries (ASLBs) have a high thickness (0.5-1.0 mm) and low ion conductance (<25 mS), which limit the cell-level energy and power densities. Based on ethyl cellulose's unique amphipathic molecular structure, superior thermal stability, and excellent binding capability, this work fabricates a freestanding SE membrane with an ultralow thickness of 47 µm. With ethyl cellulose as an effective disperser and a binder, the Li6 PS5 Cl is uniformly dispersed in toluene and possesses superior film formability. In addition, an ultralow areal resistance of 4.32 Ω cm-2 and a remarkable ion conductance of 291 mS (one order higher than the state-of-the-art sulfide SE membrane) are achieved. The ASLBs assembled with this SE membrane deliver cell-level high gravimetric and volumetric energy densities of 175 Wh kg-1 and 675 Wh L-1 , individually.

Review on Nonconventional Fibrillation Methods of Producing Cellulose Nanofibrils and Their Applications.

The production of cellulose nanofibrils (CNFs) continues to receive considerable attention because of their desirable material characteristics for a variety of consumer applications. There are, however, challenges that remain in transitioning CNFs from research to widespread adoption in the industrial sectors, including production cost and material performance. This Review covers CNFs produced from nonconventional fibrillation methods as a potential alternative solution. Pretreating biomass by biological, chemical, mechanical, or physical means can render plant feedstocks more facile for processing and thus lower energy requirements to produce CNFs. CNFs from nonconventional fibrillation methods have been investigated for various applications, including films, composites, aerogels, and Pickering emulsifiers. Continued research is needed to develop protocols to standardize the characterization (e.g., degree of fibrillation) of the lignocellulosic fibrillation processes and resulting CNF products to make them more attractive to the industry for specific product applications.

Terephthalic Acid Copolyesters Containing Tetramethylcyclobutanediol for High-Performance Plastics.

There is a need for high-performance applications for terephthalic acid (TPA) polyesters with high heat resistance, impact toughness, and optical clarity. Bisphenol A (BPA) based polycarbonates and polyarylates have such properties, but BPA is an endocrine disruptor. Therefore, new TPA polyesters that are less hazardous to health and the environment are becoming popular. Tetramethylcyclobutanediol (TMCD) is a difunctional monomer that can be polymerized with TPA and other diols to yield copolyesters with superior properties to conventional TPA polyesters. It has a cyclobutyl ring that makes it more rigid than cyclohexanedimethanol (CHDM) and EG. Thus, TMCD containing TPA copolyesters can have high heat resistance and impact strength. TPA can be made from abundantly available upcycled polyethylene terephthalate (PET). Therefore, this review discusses the synthesis of monomers and copolyesters, the impact of diol composition on material properties, molecular weight, effects of photodegradation, health safety, and substitution of cyclobutane diols for future polyesters.

Alignment of Cellulose Nanofibers: Harnessing Nanoscale Properties to Macroscale Benefits.

In nature, cellulose nanofibers form hierarchical structures across multiple length scales to achieve high-performance properties and different functionalities. Cellulose nanofibers, which are separated from plants or synthesized biologically, are being extensively investigated and processed into different materials owing to their good properties. The alignment of cellulose nanofibers is reported to significantly influence the performance of cellulose nanofiber-based materials. The alignment of cellulose nanofibers can bridge the nanoscale and macroscale, bringing enhanced nanoscale properties to high-performance macroscale materials. However, compared with extensive reviews on the alignment of cellulose nanocrystals, reviews focusing on cellulose nanofibers are seldom reported, possibly because of the challenge of aligning cellulose nanofibers. In this review, the alignment of cellulose nanofibers, including cellulose nanofibrils and bacterial cellulose, is extensively discussed from different aspects of the driving force, evaluation, strategies, properties, and applications. Future perspectives on challenges and opportunities in cellulose nanofiber alignment are also briefly highlighted.

Recent Advances in Functional Materials through Cellulose Nanofiber Templating.

Advanced templating techniques have enabled delicate control of both nano- and microscale structures and have helped thrust functional materials into the forefront of society. Cellulose nanomaterials are derived from natural polymers and show promise as a templating source for advanced materials. Use of cellulose nanomaterials in templating combines nanoscale property control with sustainability, an attribute often lacking in other templating techniques. Use of cellulose nanofibers for templating has shown great promise in recent years, but previous reviews on cellulose nanomaterial templating techniques have not provided extensive analysis of cellulose nanofiber templating. Cellulose nanofibers display several unique properties, including mechanical strength, porosity, high water retention, high surface functionality, and an entangled fibrous network, all of which can dictate distinctive aspects in the final templated materials. Many applications exploit the unique aspects of templating with cellulose nanofibers that help control the final properties of the material, including, but not limited to, applications in catalysis, batteries, supercapacitors, electrodes, building materials, biomaterials, and membranes. A detailed analysis on the use of cellulose nanofibers templating is provided, addressing specifically how careful selection of templating mechanisms and methodologies, combined toward goal applications, can be used to directly benefit chosen applications in advanced functional materials.

Surface-modified and oven-dried microfibrillated cellulose reinforced biocomposites: Cellulose network enabled high performance.

Microfibrillated cellulose (MFC) is widely used as a reinforcement filler for biocomposites due to its unique properties. However, the challenge of drying MFC and the incompatibility between nanocellulose and polymer matrix still limits the mechanical performance of MFC-reinforced biocomposites. In this study, we used a water-based transesterification reaction to functionalize MFC and explored the capability of oven-dried MFC as a reinforcement filler for polylactic acid (PLA). Remarkably, this oven-dried, vinyl laurate-modified MFC improved the tensile strength by 38 % and Young's modulus by 71 % compared with neat PLA. Our results suggested improved compatibility and dispersion of the fibrils in PLA after modification. This study demonstrated that scalable water-based surface modification and subsequent straightforward oven drying could be a facile method for effectively drying cellulose nanomaterials. The method helps significantly disperse fibrils in polymers and enhances the mechanical properties of microfibrillar cellulose-reinforced biocomposites.

Material Extrusion Additive Manufacturing of Wood and Lignocellulosic Filled Composites.

Wood and lignocellulosic-based material components are explored in this review as functional additives and reinforcements in composites for extrusion-based additive manufacturing (AM) or 3D printing. The motivation for using these sustainable alternatives in 3D printing includes enhancing material properties of the resulting printed parts, while providing a green alternative to carbon or glass filled polymer matrices, all at reduced material costs. Previous review articles on this topic have focused only on introducing the use of natural fillers with material extrusion AM and discussion of their subsequent material properties. This review not only discusses the present state of materials extrusion AM using natural filler-based composites but will also fill in the knowledge gap regarding state-of-the-art applications of these materials. Emphasis will also be placed on addressing the challenges associated with 3D printing using these materials, including use with large-scale manufacturing, while providing insight to overcome these issues in the future.

Life Cycle Assessment of Compostable Coffee Pods: A US University Based Case Study.

Single-serve machines have proven to be a rapid and convenient mechanism for preparing coffee for consumption. However, disposing the single-use coffee pods accompanying each use creates insurmountable waste in landfills. With the introduction of biobased products being certified as industrially compostable, there is scope for an effective waste stream for nearly all biobased products that avoids adding to landfills. The case presented in this paper demonstrates the success of composting compostable coffee pods within a local industrial-scale composting facility. Utilizing the existing local composting facility at the University of Tennessee-Knoxville, a life cycle assessment was performed to calculate the overall embodied energy and related environmental impact(s) to determine the feasibility of using compostable coffee pods over conventional plastic ones. Testing showed complete degradation within 46 days, proving composting to be a feasible waste stream option and a sustainable marketing edge while treading the path toward a circular economy. Cost savings of 21% were realized in terms of waste disposal, in addition to creating a value-added product at the end of the coffee pods life cycle, with nutrient-rich compost being recirculated to campus gardens and farms.

Biogas Reforming to Syngas: A Review.

Interest in novel uses of biogas has increased recently due to concerns about climate change and greater emphasis on renewable energy sources. Although biogas is frequently used in low-value applications such as heating and fuel in engines or even just flared, reforming is an emerging strategy for converting biogas to syngas, which could then be used to obtain high-value-added liquid fuels and chemicals. Interest also exists due to the role of dry, bi-, and tri-reforming in the capture and utilization of CO2. New research efforts have explored efficient and effective reforming catalysts, as specifically applied to biogas. In this paper, we review recent developments in dry, bi-, and tri-reforming, where the CO2 in biogas is used as an oxidant/partial oxidant. The synthesis, characterization, lifetime, deactivation, and regeneration of candidate reforming catalysts are discussed in detail. The thermodynamic limitation and techno-economics of biogas conversion are also discussed.

Synthesis, Characterization, and Utilization of a Lignin-Based Adsorbent for Effective Removal of Azo Dye from Aqueous Solution.

How to effectively remove toxic dyes from the industrial wastewater using a green low-cost lignocellulose-based adsorbent, such as lignin, has become a topic of great interest but remains quite challenging. In this study, cosolvent-enhanced lignocellulosic fractionation (CELF) pretreatment and Mannich reaction were combined to generate an aminated CELF lignin which is subsequently applied for removal of methylene blue and direct blue (DB) 1 dye from aqueous solution. 31P NMR was used to track the degree of amination, and an orthogonal design was applied to determine the relationship between the extent of amination and reaction parameters. The physicochemical, morphological, and thermal properties of the aminated CELF lignin were characterized to confirm the successful grafting of diethylenetriamine onto the lignin. The aminated CELF lignin proved to be an effective azo dye-adsorbent, demonstrating considerably enhanced dye decolorization, especially toward DB 1 dye (>90%). It had a maximum adsorption capacity of DB 1 dye of 502.7 mg/g, and the kinetic study suggested the adsorption process conformed to a pseudo-second-order kinetic model. The isotherm results also showed that the modified lignin-based adsorbent exhibited monolayer adsorption. The adsorbent properties were mainly attributed to the incorporated amine functionalities as well as the increased specific surface area of the aminated CELF lignin.

Liquid crystalline networks based on photo-initiated thiol-ene click chemistry.

Photo-initiated thiol-ene click chemistry is used to develop shape memory liquid crystalline networks (LCNs). A biphenyl-based di-vinyl monomer is synthesized and cured with a di-thiol chain extender and a tetra-thiol crosslinker using UV light. The effects of photo-initiator concentration and UV light intensity on the curing behavior and liquid crystalline (LC) properties of the LCNs are investigated. The chemical composition is found to significantly influence the microstructure and the related thermomechanical properties of the LCNs. The structure-property relationship is further explored using molecular dynamics simulations, revealing that the introduction of the chain extender promotes the formation of an ordered smectic LC phase instead of agglomerated structures. The concentration of the chain extender affects the liquid crystallinity of the LCNs, resulting in distinct thermomechanical and shape memory properties. This class of LCNs exhibits fast curing rates, high conversion levels, and tailorable liquid crystallinity, making it a promising material system for advanced manufacturing, where complex and highly ordered structures can be produced with fast reaction kinetics and low energy consumption.

Poplar as Biofiber Reinforcement in Composites for Large-Scale 3D Printing.

The economic viability of the biofuel industry could be improved by adding a high-value revenue stream for biomass supply chains: bioderived composites for the rapidly expanding large-scale additive manufacturing industry (i.e., 3D printing). Using fibrillated fibers derived from biomass (e.g., Populus) to reinforce polymers for 3D printing applications would be less expensive compared to using conventional carbon fibers. Poplar fibers of different mesh sizes (<180, 180-425, 425-850, and 850-2360 µm) were used to prepare poplar-polylactic acid (PLA) composites. The poplar/PLA composites were successfully printed using a large-scale 3D printer to create a podium support. The tensile strength of the composites increased from 34 to 54 MPa as the poplar fiber size decreased. The fracture surfaces of composites derived from smaller poplar fibers (<180 µm) were more compact with fewer voids compared with the composites made with larger poplar fibers. Because of the porous and hollow microstructures, smaller poplar fibers contained more pores on their outer surfaces, which were available for the access and penetration of PLA. Poplar has potential for use as a thermoplastic reinforcement for large-scale 3D printing.

Nanoporous Boron Nitride as Exceptionally Thermally Stable Adsorbent: Role in Efficient Separation of Light Hydrocarbons.

In this work, nanoporous boron nitride sample was synthesized with a Brunauer-Emmett-Teller (BET) surface area of 1360 m2/g and particle size 5-7 µm. The boron nitride was characterized with X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and electron microscopy (TEM and SEM). Thermogravimetric analysis (TGA) under nitrogen and air and subsequent analysis with XPS and XRD suggested that its structure is stable in air up to 800 °C and in nitrogen up to 1050 °C, which is higher than most of the common adsorbents reported so far. Nitrogen and hydrocarbon adsorption at 298 K and pressure up to 1 bar suggested that all hydrocarbon adsorption amounts were higher than that of nitrogen and the adsorbed amount of hydrocarbon increases with an increase in its molecular weight. The kinetics of adsorption data suggested that adsorption becomes slower with the increase in molecular weight of hydrocarbons. The equilibrium data suggested that that boron nitride is selective to paraffins in a paraffin-olefin mixture and hence may act as an "olefin generator". The ideal adsorbed solution theory (IAST)-based selectivity for CH4/N2, C2H6/CH4, and C3H8/C3H6 was very high and probably higher than the majority of adsorbents reported in the literature. IAST-based calculations were also employed to simulate the binary mixture adsorption data for the gas pairs of CH4/N2, C2H6/CH4, C2H6/C2H4, and C3H8/C3H6. Finally, a simple mathematical model was employed to simulate the breakthrough behavior of the above-mentioned four gas pairs in a dynamic column experiment. The overall results suggest that nanoporous boron nitride can be used as a potential adsorbent for light hydrocarbon separation.

Improved mechanical properties of polylactide nanocomposites-reinforced with cellulose nanofibrils through interfacial engineering via amine-functionalization.

One of the main factors responsible for the mechanical and physical properties of nanocomposites is the effectiveness of the interfacial region to transfer loads and mechanical vibrations between the nano-reinforcements and the matrix. Surface functionalization has been the preferred approach to engineer the interfaces in polymer nanocomposites in order to maximize their potential in structural and functional applications. In this study, amine-functionalized cellulose nanofibrils (mCNF-G1) were synthesized via silylation of the hydroxyl groups on the CNF surface using 3-aminopropyltrimethoxysilane (APTMS). To further increase the amine density (mCNF-G2), dendritic polyamidoamine (PAMAM) was grafted onto mCNF-G1 by the Michael addition of methacrylate onto mCNF-G1, followed by the transamidation of the ester groups of methacrylate using ethylenediamine. Compared to native CNF-reinforced, poly(l-lactide) (PLLA) nanocomposites, amine-functionalized CNF exhibited significantly improved dispersion and interfacial properties within the PLLA matrix due to the grafting of PLLA chains via aminolysis. It is also a more effective nucleating agent, with 15% mCNF-G1 leading to a crystallinity of 32.5%, compared to 0.1 and 8.7% for neat PLLA and native CNF-reinforced composites. We have demonstrated that APTMS-functionalized CNF (mCNF-G1) significantly improved the tensile strength compared to native CNF, with 10% mCNF-G1 being the most effective (i.e., >100% increase in tensile strength). However, we also found that excessive amines on the CNF surface (i.e., mCNF-G2) resulted in decreased tensile strength and modulus due to PLLA degradation via aminolysis. These results demonstrate the potential of optimized amine-functionalized CNF for future renewable material applications.