Highly Dispersed Mn-Doped Ceria Supported on N-Doped Carbon Nanotubes for Enhanced Oxygen Reduction Reaction.

The weak adsorption of oxygen on transition metal oxide catalysts limits the improvement of their electrocatalytic oxygen reduction reaction (ORR) performance. Herein, a dopamine-assisted method is developed to prepare Mn-doped ceria supported on nitrogen-doped carbon nanotubes (Mn-Ce-NCNTs). The morphology, dispersion of Mn-doped ceria, composition, and oxygen vacancies of the as-prepared catalysts were analyzed using various technologies. The results show that Mn-doped ceria was formed and highly dispersed on NCNTs, on which oxygen vacancies are abundant. The as-prepared Mn-Ce-NCNTs exhibit a high ORR performance, on which the average electron transfer number is 3.86 and the current density is 24.4% higher than that of commercial 20 wt % Pt/C. The peak power density of Mn-Ce-NCNTs is 68.1 mW cm-2 at the current density of 138.9 mA cm-2 for a Zn-air battery, which is close to that of 20 wt % Pt/C (69.4 mW cm-2 at 106.1 mA cm-2). Density functional theory (DFT) calculations show that the oxygen vacancy formation energies of Mn-doped CeO2(111) and pure CeO2(111) are -0.55 and 2.14 eV, respectively. Meanwhile, compared with undoped CeO2(111) (-0.02 eV), Mn-doped CeO2(111) easily adsorbs oxygen with the oxygen adsorption energy of only -0.68 eV. This work provides insights into the synergetic effect of Mn-doped ceria for facilitating oxygen adsorption and enhancing ORR performance.

Research progress of dual-atom site catalysts for photocatalysis.

Dual-atom site catalysts (DASCs) have sparked considerable interest in heterogeneous photocatalysis as they possess the advantages of excellent photoelectronic activity, photostability, and high carrier separation efficiency and mobility. The DASCs involved in these important photocatalytic processes, especially in the photocatalytic hydrogen evolution reaction (HER), CO2 reduction reaction (CO2RR), N2/nitrate reduction, etc., have been extensively investigated in the past few years. In this review, we highlight the recent progress in DASCs that provides fundamental insights into the photocatalytic conversion of small molecules. The controllable preparation and characterization methods of various DASCs are discussed. Subsequently, the reaction mechanisms of the formation of several important molecules (hydrogen, hydrocarbons and ammonia) on DASCs are introduced in detail, in order to probe the relationship between DASCs's structure and photocatalytic activity. Finally, some challenges and outlooks of DASCs in the photocatalytic conversion of small molecules are summarized and prospected. We hope that this review can provide guidance for in-depth understanding and aid in the design of efficient DASCs for photocatalysis.

Fe-Co heteronuclear atom pairs as catalytic sites for efficient oxygen electroreduction.

Single-site Fe-N-C catalysts are the most promising Pt-group catalyst alternatives for the oxygen reduction reaction, but their application is impeded by their relatively low activity and unsatisfactory stability as well as production costs. Here, cobalt atoms are introduced into an Fe-N-C catalyst to enhance its catalytic activity by utilizing the synergistic effect between Fe and Co atoms. Meanwhile, phenanthroline is employed as the ligand, which favours stable pyridinic N-coordinated Fe-Co sites. The obtained catalysts exhibit excellent ORR performance with a half-wave potential of 0.892 V and good stability under alkaline conditions. In addition, the excellent ORR activity and durability of FeCo-N-C enabled the constructed zinc-air battery to exhibit a high power density of 247.93 mW cm-2 and a high capacity of 768.59 mA h gZn-1. Moreover, the AEMFC based on FeCo-N-C also achieved a high open circuit voltage (0.95 V) and rated power density (444.7 mW cm-2), surpassing those of many currently reported transition metal-based cathodes. This work emphasizes the feasibility of this non-precious metal catalyst preparation strategy and its practical applicability in fuel cells and metal-air batteries.

Advances in Heterogeneous Catalysts for Lignin Hydrogenolysis.

Lignin is the main component of lignocellulose and the largest source of aromatic substances on the earth. Biofuel and bio-chemicals derived from lignin can reduce the use of petroleum products. Current advances in lignin catalysis conversion have facilitated many of progress, but understanding the principles of catalyst design is critical to moving the field forward. In this review, the factors affecting the catalysts (including the type of active metal, metal particle size, acidity, pore size, the nature of the oxide supports, and the synergistic effect of the metals) are systematically reviewed based on the three most commonly used supports (carbon, oxides, and zeolites) in lignin hydrogenolysis. The catalytic performance (selectivity and yield of products) is evaluated, and the emerging catalytic mechanisms are introduced to better understand the catalyst design guidelines. Finally, based on the progress of existing studies, future directions for catalyst design in the field of lignin depolymerization are proposed.

Avoiding Sabatier's Limitation on Spatially Correlated Pt-Mn Atomic Pair Sites for Oxygen Electroreduction.

The development of highly active and low-cost oxygen reduction reaction (ORR) catalysts is crucial for the practical application of hydrogen fuel cells. However, the linear scaling relation (LSR) imposes an inherent Sabatier's limitation for most catalysts including the benchmark Pt with an insurmountable overpotential ceiling, impeding the development of efficient electrocatalysts. To avoid such a limitation, using earth-abundant metal oxides with different crystal phases as model materials, we propose an effective and dynamic reaction pathway through constructing spatially correlated Pt-Mn pair sites, achieving an excellent balance between high activity and low Pt loading. Experimental and theoretical calculations demonstrate that manipulating the intermetallic distance and charge distribution of Pt-Mn pairs can effectively promote O-O bond cleavage at these sites through a bridge configuration, circumventing the formation of *OOH intermediates. Meanwhile, the dynamic adsorption configuration transition from the bridge configuration of O2 to the end-on configuration of *OH improves *OH desorption at the Mn site within such pairs, thereby avoiding Sabatier's limitation. The well-designed Pt-Mn/ß-MnO2 exhibits outstanding ORR activity and stability with a half-wave potential of 0.93 V and barely any activity degradation for 70 h. When applied to the cathode of a H2-O2 anion-exchange membrane fuel cell, this catalyst demonstrates a high peak power density of 287 mW cm-2 and 500 h of stability under a cell voltage of 0.6 V. This work reveals the adaptive bonding interactions of atomic pair sites with multiple reactant/intermediates, offering a new avenue for rational design of highly efficient atomic-level dispersed ORR catalysts beyond the Sabatier optimum.

Progress in Manipulating Dynamic Surface Reconstruction via Anion Modulation for Electrocatalytic Water Oxidation.

The development of efficient and economical electrocatalysts for oxygen evolution reaction (OER) is of paramount importance for the sustainable production of renewable fuels and energy storage systems; however, the sluggish OER kinetics involving multistep four proton-coupled electron transfer hampers progress in these systems. Fortunately, surface reconstruction offers promising potential to improve OER catalyst design. Anion modulation plays a crucial role in controlling the extent of surface reconstruction and positively persuading the reconstructed species' performances. This review starts by providing a general explanation of how various types of anions can trigger dynamic surface reconstruction and create different combinations with pre-catalysts. Next, the influences of anion modulation on manipulating the surface dynamic reconstruction process are discussed based on the in situ advanced characterization techniques. Furthermore, various effects of survived anionic groups in reconstructed species on water oxidation activity are further discussed. Finally, the challenges and prospects for the future development directions of anion modulation for redirecting dynamic surface reconstruction to construct highly efficient and practical catalysts for water oxidation are proposed.

Reconstructed Ir‒O‒Mo species with strong Brønsted acidity for acidic water oxidation.

Surface reconstruction generates real active species in electrochemical conditions; rational regulating reconstruction in a targeted manner is the key for constructing highly active catalyst. Herein, we use the high-valence Mo modulated orthorhombic Pr3Ir1-xMoxO7 as model to activate lattice oxygen and cations, achieving directional and accelerated surface reconstruction to produce self-terminated Ir‒Obri‒Mo (Obri represents the bridge oxygen) active species that is highly active for acidic water oxidation. The doped Mo not only contributes to accelerated surface reconstruction due to optimized Ir‒O covalency and more prone dissolution of Pr, but also affords the improved durability resulted from Mo-buffered charge compensation, thereby preventing fierce Ir dissolution and excessive lattice oxygen loss. As such, Ir‒Obri‒Mo species could be directionally generated, in which the strong Brønsted acidity of Obri induced by remaining Mo assists with the facilitated deprotonation of oxo intermediates, following bridging-oxygen-assisted deprotonation pathway. Consequently, the optimal catalyst exhibits the best activity with an overpotential of 259 mV to reach 10 mA cmgeo-2, 50 mV lower than undoped counterpart, and shows improved stability for over 200 h. This work provides a strategy of directional surface reconstruction to constructing strong Brønsted acid sites in IrOx species, demonstrating the perspective of targeted electrocatalyst fabrication under in situ realistic reaction conditions.

Spin selection in atomic-level chiral metal oxide for photocatalysis.

The spin degree of freedom is an important and intrinsic parameter in boosting carrier dynamics and surface reaction kinetics of photocatalysis. Here we show that chiral structure in ZnO can induce spin selectivity effect to promote photocatalytic performance. The ZnO crystals synthesized using chiral methionine molecules as symmetry-breaking agents show hierarchical chirality. Magnetic circular dichroism spectroscopic and magnetic conductive-probe atomic force microscopic measurements demonstrate that chiral structure acts as spin filters and induces spin polarization in photoinduced carriers. The polarized carriers not only possess the prolonged carrier lifetime, but also increase the triplet species instead of singlet byproducts during reaction. Accordingly, the left- and right-hand chiral ZnO exhibit 2.0- and 1.9-times higher activity in photocatalytic O2 production and 2.5- and 2.0-times higher activities in contaminant photodegradation, respectively, compared with achiral ZnO. This work provides a feasible strategy to manipulate the spin properties in metal oxides for electron spin-related redox catalysis.

Applied Forces Changed Myopia Lens Optical Performance but Not Retinal Image Quality Tested Using a Newly Designed Digital Colmascope.

Background: The aim of this study was to investigate the effects of applied forces generated by a rim screw on the optical performance of mounted myopia lenses. The residual refractive error and retinal image quality of the corrected eyes were also investigated. Methods: For 120 lenses, internal lens stress was measured using a newly designed digital strain viewer (colmascope). Sixty myopic adults (120 eyes) were recruited. The effects of internal lens stress on residual refraction and retinal image quality were evaluated using OPD Scan III. The results were compared between loose and tight mounting and between the right and left eyes. Results: Significant differences were observed among nine lens zones in both the right and left lenses, regardless of the mounting state (P < 0.001). The differences were mainly derived from the five vertically arranged zones (P < 0.05). Significant differences in internal lens stress were observed between the right and left lenses (P < 0.05). No significant differences in central residual refractive error and retinal image quality of the corrected eyes were found between the loose- and tight-mounted lenses. Conclusion: The applied forces generated by the rim screw changed the peripheral optical performance of the mounted myopia lenses but exerted only negligible impacts on the central residual refractive error and visual image quality.

Synergetic effect of Au nanoparticles and transition metal phosphides for enhanced hydrogen evolution from ammonia-borane.

The hydrogen evolution from ammonia borane is intriguing but challenging due to its sluggish kinetics. In this regard, the gold nanoparticles amalgamation with metal phosphides is speculated to be more efficient catalysts. Here, the catalysts Au/Ni2P and Au/CoP with the high synergetic effect of Au nanoparticles and metal phosphides were synthesized for ammonia borane hydrolysis. The activity of Au/Ni2P increases 4.8-fold (i.e., 0.08 to 0.40 L∙h-1) compared to pristine Ni2P, and the activity of Au/CoP increases 1.7-fold (i.e., 0.74 to 1.27 L∙h-1) compared to pristine CoP. This reveals that the synergetic effect of Auδ+ and (Ni2P) δ- is stronger than Auδ+ and (CoP) δ- which is manifested by XPS analysis. The kinetics exposes that the activation energy of Au/Ni2P (45.28 kJ∙mole-1) is greater than Au/CoP (31.45 kJ∙mole-1) and the TOF of Au/Ni2P is less than Au/CoP. This research work presents an effective approach for producing active sites of Auδ+ and (Ni2P & CoP) δ- for ammonia borane hydrolysis to enhance the H2 evolution rate.

IrO2 Nanoparticle-Decorated Ir-Doped W18O49 Nanowires with High Mass Specific OER Activity for Proton Exchange Membrane Electrolysis.

The oxygen evolution reaction (OER) severely limits the efficiency of proton exchange membrane (PEM) electrolyzers due to slow reaction kinetics. IrO2 is currently a commonly used anode catalyst, but its large-scale application is limited due to its high price and scarce reserves. Herein, we reported a practical strategy to construct an acid OER catalyst where Iridium oxide loading and iridium element bulk doping are realized on the surface and inside of W18O49 nanowires by immersion adsorption, respectively. Specifically, W0.7Ir0.3Oy has an overpotential of 278 mV at 10 mA·cm-2 in 0.1 M HClO4. The mass activity of 714.10 A·gIr-1 at 1.53 V vs. the reversible hydrogen electrode (RHE) is 80 times that of IrO2, and it can run stably for 55 h. In the PEM water electrolyzer device, its mass activity reaches 3563.63 A·gIr-1 at the cell voltage of 2.0 V. This improved catalytic performance is attributed to the following aspects: (1) The electron transport between iridium and tungsten effectively improves the electronic structure of the catalyst; (2) the introduction of iridium into W18O49 by means of elemental bulk doping and nanoparticles supporting for the enhanced conductivity and electrochemically active surface area of the catalyst, resulting in extensive exposure of active sites and increased intrinsic activity; and (3) during the OER process, partial iridium elements in the bulk phase are precipitated, and iridium oxide is formed on the surface to maintain stable activity. This work provides a new idea for designing oxygen evolution catalysts with low iridium content for practical application in PEM electrolyzers.

Tracking the Role of Defect Types in Co3O4 Structural Evolution and Active Motifs during Oxygen Evolution Reaction.

Dynamic reconstruction of catalyst active sites is particularly important for metal oxide-catalyzed oxygen evolution reaction (OER). However, the mechanism of how vacancy-induced reconstruction aids OER remains ambiguous. Here, we use Co3O4 with Co or O vacancies to uncover the effects of different defects in the reconstruction process and the active motifs relevant to alkaline OER. Combining in situ characterization and theoretical calculations, we found that cobalt oxides are converted to an amorphous [Co(OH)6] intermediate state, and then the mismatched rates of *OH adsorption and deprotonation lead to irreversible catalyst reconstruction. The stronger *OH adsorption but weaker deprotonation induced by O defects provides the driving force for reconstruction, while Co defects favor dehydrogenation and reduce the reconstruction rate. Importantly, both O and Co defects trigger highly OER-active bridge Co sites in reconstructed catalysts, of which Co defects induce a short Co-Co distance (3.38 Å) under compressive lattice stress and show the best OER activity (η10 of 262 mV), superior to reconstructed oxygen-defected Co3O4-VO (η10 of 300 mV) and defect-free Co3O4 (η10 of 320 mV). This work highlights that engineering defect-dependent reconstruction may provide a rational route for electrocatalyst design in energy-related applications.

Advances in Selective Electrochemical Oxidation of 5-Hydroxymethylfurfural to Produce High-Value Chemicals.

The conversion of biomass is a favorable alternative to the fossil energy route to solve the energy crisis and environmental pollution. As one of the most versatile platform compounds, 5-hydroxymethylfural (HMF) can be transformed to various value-added chemicals via electrolysis combining with renewable energy. Here, the recent advances in electrochemical oxidation of HMF, from reaction mechanism to reactor design are reviewed. First, the reaction mechanism and pathway are summarized systematically. Second, the parameters easy to be ignored are emphasized and discussed. Then, the electrocatalysts are reviewed comprehensively for different products and the reactors are introduced. Finally, future efforts on exploring reaction mechanism, electrocatalysts, and reactor are prospected. This review provides a deeper understanding of mechanism for electrochemical oxidation of HMF, the design of electrocatalyst and reactor, which is expected to promote the economical and efficient electrochemical conversion of biomass for industrial applications.

Engineering interfacial band bending over bismuth vanadate/carbon nitride by work function regulation for efficient solar-driven water splitting.

Nature-inspired artificial Z-scheme photocatalyst offers great promise in solar overall water splitting, but its rational design, construction and interfacial charge transfer mechanism remain ambiguous. Here, we design an approach of engineering interfacial band bending via work function regulation, which realizes directional charge transfer at interface and affords direct Z-scheme pathway. Taking BiVO4 as prototype, its oxygen vacancy concentration is reduced by slowing down the crystallization rate, thereby changing the work function from smaller to larger than that of polymeric carbon nitride (PCN). Consequently, the photoinduced charge transfer pathway of BiVO4/PCN is switched from type-II to Z-scheme as evidenced by synchronous illuminated X-ray photoelectron spectroscopy (XPS) and femtosecond transient absorption spectroscopy. Specifically, the direct Z-scheme BiVO4/PCN shows superior photocatalytic performance in water splitting. This work provides deep insights and guidelines to constructing heterojunction photocatalysts for solar utilization.

The Reliability and Acceptability of RDx-Based Tele-Controlled Subjective Refraction Compared with Traditional Subjective Refraction.

Purpose: The purpose of this study was to compare the reliability and acceptability of tele-controlled subjective refraction supported by RDx, a new technique that involves optical software designed for controlling phoropters remotely, to traditional subjective refraction. Methods: Sixty-five participants underwent tele-controlled subjective refraction and traditional subjective refraction randomly and nine of them underwent the second tele-controlled subjective refraction measurement on the same day. After their examinations, we distributed a validated satisfaction questionnaire to each participant. The elapsed time taken for refraction, sphere (S), cylinder (C), spherical equivalent (SE), vertical and oblique cylindrical vectors (J0 and J45), and best corrected visual acuity (BCVA) were compared. Age and refractive error type were included as covariates. Bland-Altman analysis was used to assess the agreement between both methods of refraction. Results: The mean age was 20.5 ± 5.9 years for all participants (aged 9 to 40 years); 57% were female participants. The repeatability analysis of tele-controlled method showed no significant differences for all parameters (P > 0.05). We found no statistical differences (P > 0.05) between tele-controlled subjective refraction and traditional subjective refraction for all parameters in either group. The mean difference and 95% limits of agreement for SE, J0, and J45 were -0.03 ± 0.36 diopters (D), -0.00 ± 0.57 D, and -0.01 ± 0.79 D, respectively. The tele-controlled method took more time to perform than the traditional one (P < 0.05). Completed questionnaires were returned by 55 participants (85%), and they showed high satisfaction and acceptance of the tele-controlled method (98%). Conclusions: Tele-controlled subjective refraction results agreed with traditional subjective refraction for all refraction components except for cylinder vectors. In addition, the broad acceptability of tele-controlled subjective refraction means practicability in clinical practice. Translation Relevance: The RDx-based tele-controlled method can provide an alternative to subjective refraction, especially in areas that lack experienced optometrists.

Interface Engineering of Conjugated Polymer-Based Composites for Photocatalysis.

Photocatalysis can create a green way to produce clean energy resources, degrade pollutants and achieve carbon neutrality, making the construction of efficient photocatalysts significant in solving environmental issues. Conjugated polymers (CPs) with adjustable band structures have superior light-absorption capacity and flexible morphology that facilitate contact with other components to form advanced heterojunctions. Interface engineering can strengthen the interfacial contact between the components and further enlarge the interfacial contact area, enhance light absorption, accelerate charge transfer and improve the reusability of the composites. In order to throw some new light on heterojunction interface regulation at a molecular level, herein we summarize CP-based composites with improved photocatalytic performance according to the types of interactions (covalent bonding, hydrogen bonding, electrostatic interactions, π-π stacking, and other polar interactions) between the components and introduce the corresponding interface building methods, identifying techniques. Then the roles of interfaces in different photocatalytic applications are discussed. Finally, we sum up the existing problems in interface engineering of CP-based composites and look forward to the possible solutions.

Rational Design of Better Hydrogen Evolution Electrocatalysts for Water Splitting: A Review.

The excessive dependence on fossil fuels contributes to the majority of CO2 emissions, influencing on the climate change. One promising alternative to fossil fuels is green hydrogen, which can be produced through water electrolysis from renewable electricity. However, the variety and complexity of hydrogen evolution electrocatalysts currently studied increases the difficulty in the integration of catalytic theory, catalyst design and preparation, and characterization methods. Herein, this review first highlights design principles for hydrogen evolution reaction (HER) electrocatalysts, presenting the thermodynamics, kinetics, and related electronic and structural descriptors for HER. Second, the reasonable design, preparation, mechanistic understanding, and performance enhancement of electrocatalysts are deeply discussed based on intrinsic and extrinsic effects. Third, recent advancements in the electrocatalytic water splitting technology are further discussed briefly. Finally, the challenges and perspectives of the development of highly efficient hydrogen evolution electrocatalysts for water splitting are proposed.

Pd/Fe2O3 with Electronic Coupling Single-Site Pd-Fe Pair Sites for Low-Temperature Semihydrogenation of Alkynes.

Dispersing single palladium atoms on a support is promising to minimize the usage of palladium and improve the selectivity for alkyne semihydrogenation, but its activity is often very low as a result of unfavorable H2 activation. Here, we load palladium onto α-Fe2O3(012) to construct highly active and stable single-site Pd-Fe pairs with luxuriant d-electron domination near the Fermi level driven by strong electronic coupling and prove that Pd-Fe pairs cooperatively adsorb H2 and dissociate an H─H bond, whereas solo Pd sites enable preferential desorption of C═C intermediate, thus achieving both high activity and high selectivity for alkyne hydrogenation. This catalyst exhibits state-of-the-art performance in purifying acetylene of ethylene stream, with 99.6% and 100% conversion and 96.7% and 94.7% selectivity at 353 and 393 K, respectively, and excellent stability with negligible activity decay after a 200 h test. This single-site pair inherits the advantage but overcomes the weakness of both Pd ensemble and single Pd atoms, enabling ultralow-Pd-loading catalysts for selective hydrogenation.

Methane Dry Reforming by Ni-Cu Nanoalloys Anchored on Periclase-Phase MgAlOx Nanosheets for Enhanced Syngas Production.

Stable and efficient syngas production via methane dry reforming is highly desirable as it utilizes two greenhouse gases simultaneously. In this work, active Ni-Cu nanoalloys stably anchored on periclase-phase MgAlOx nanosheets were successfully synthesized by a hydrothermal method. These highly dispersed small Ni-Cu alloys strongly interacted with the periclase-phase MgAlOx nanosheets, on which abundant base sites were accessible. On the optimal catalyst (6Ni6CuMgAl-S), methane and carbon dioxide conversion always reached 85 and 90% at 700 °C under a gas hour speed velocity of 40,000 mL/gcat h for more than 70 h. The hydrogen production rate was maintained at 1.8 mmol/min, and the ratio of H2/CO was kept at approximately 0.96 under a CH4 and CO2 flow rate of 25 mL/min. Coke deposition and Ni sintering were effectively suppressed by the formation of a Ni-Cu alloy, the laminar structure, and the periclase phase of the MgAlOx support. Moreover, the alloy nanoparticles were reconstructed into a segregated Ni-Cu alloy structure in response to the reaction environment, and this structure was more stable and still active. Density functional theory calculations showed that carbon adsorption was inhibited on the segregated Ni-Cu alloy. Furthermore, the experimental thermogravimetric and O2-TPO results confirmed the significant decrease in carbon deposition on the Ni-Cu alloy catalysts.

Synergy of Iron Doping and Cyano Groups for Enhanced Photocatalytic Hydrogen Production over C3 N4.

Improving the insufficient carrier separation dynamics is still of significance in carbon nitride (C3 N4 ) research. Extensive research has been devoted to improving the carrier separation efficiency through a single strategy, while ignoring the synergistic enhancement effect produced by coupling two or more conventional strategies. Herein, we reported the fabrication of cyano group-containing Fe-doped C3 N4 porous materials via direct co-calcination of iron acetylacetonate and melamine for synergistically improving the photocatalytic performance. Iron acetylacetonate can promote the generation of cyano groups and form Fe-doping in C3 N4 , thereby increasing the visible-light absorption and reactive sites. Further, the internal donor-acceptor system formed by cyano groups and Fe-doped sites promoted charge carrier separation and inhibited the radiation recombination of e- -h+ pairs. The optimized photocatalytic activity of Fe-CN-2 sample was 4.5 times of bulk C3 N4 (BCN).