RESUMEN
Combinatorial spread libraries offer an approach to explore the evolution of material properties over broad concentration, temperature, and growth parameter spaces. However, the traditional limitation of this approach is the requirement for the read-out of functional properties across the library. Here we develop automated piezoresponse force microscopy (PFM) for the exploration of combinatorial spread libraries and demonstrate its application in the SmxBi1-xFeO3 system with the ferroelectric-antiferroelectric morphotropic phase boundary. This approach relies on the synergy of the quantitative nature of PFM and the implementation of automated experiments that allow PFM-based sampling of macroscopic samples. The concentration dependence of pertinent ferroelectric parameters was determined and used to develop the mathematical framework based on the Ginzburg-Landau theory describing the evolution of these properties across the concentration space. We pose that a combination of automated scanning probe microscope and combinatorial spread library approach will emerge as an efficient research paradigm to close the characterization gap in high-throughput materials discovery. We make the data sets open to the community, and we hope that this will stimulate other efforts to interpret and understand the physics of these systems.
RESUMEN
Humidity monitoring has become extremely vital in various technological fields such as environment control, biomedical engineering, and so on. Therefore, a substantial interest lies in the development of fast and highly sensitive devices with high figures of merit. Self-powered and ultrasensitive humidity sensors based on SnS2 nanofilms of different film thicknesses have been demonstrated in this work. The sensing behavior has been investigated in the relative humidity (RH) range of 2-99%. The observed results reveal a remarkable response and ultrafast detection even with zero applied bias (self-powered mode), with response and recovery times of ~ 10 and ~ 0.7 s, respectively. The self-powered behavior has been attributed to the inhomogeneities and the asymmetry in the contact electrodes. The highest sensitivity of ~ 5.64 × 106% can be achieved at an applied bias of 5 V. This approach of fabricating such highly responsive, self-powered and ultrafast sensors with simple device architectures will be useful for designing futuristic sensing devices.
RESUMEN
A self-powered, broad band and ultrafast photodetector based on n+-InGaN/AlN/n-Si(111) heterostructure is demonstrated. Si-doped (n+ type) InGaN epilayer was grown by plasma-assisted molecular beam epitaxy on a 100 nm thick AlN template on an n-type Si(111) substrate. The n+-InGaN/AlN/n-Si(111) devices exhibit excellent self-powered photoresponse under UV-visible (300-800 nm) light illumination. The maximum response of this self-powered photodetector is observed at 580 nm for low-intensity irradiance (0.1 mW/cm2), owing to the deep donor states present near the InGaN/AlN interface. It shows a responsivity of 9.64 A/W with rise and fall times of 19.9 and 21.4 µs, respectively. A relation between the open circuit voltage and the responsivity has been realized.
RESUMEN
Nonpolar a-plane GaN epitaxial films were grown on an r-plane sapphire using the plasma-assisted molecular beam epitaxy system, with various nitrogen plasma power conditions. The crystallinity of the films was characterized by high-resolution X-ray diffraction and reciprocal space mapping. Using the X-ray "rocking curve-phi scan", [0002], [1-100], and [1-102] azimuth angles were identified, and interdigitated electrodes along these directions were fabricated to evaluate the direction-dependent UV photoresponses. UV responsivity ( R) and internal gain ( G) were found to be dependent on the azimuth angle and in the order of [0002] > [1-102] > [1-100], which has been attributed to the enhanced crystallinity and lowest defect density along [0002] azimuth. The temporal response was very stable irrespective of growth conditions and azimuth angles. Importantly, response time, responsivity, and internal gain were 210 ms, 1.88 A W-1, and 648.9%, respectively, even at a bias as low as 1 V. The results were validated using the Silvaco Atlas device simulator, and experimental observations were consistent with simulated results. Overall, the photoresponse is dependent on azimuth angles and requires further optimization, especially for materials with in-plane crystal anisotropy.
RESUMEN
Clay-based nanostructured multilayers, such as clay-polymer multilayers and clay-oxide multilayers, have attracted growing attention owing to their remarkable mechanical properties and promising application in various fields. In this paper, synthesis of a new kind of nanostructured clay-oxide multilayers by layer-by-layer self-assembly was explored. Nano-mechanical characterization of 18 clay-based multilayer samples, prepared under as-deposited (i.e., air-dried) and annealing conditions at 400 °C/600 °C with different precursor cations and multilayer structure, were carried out using nanoindentation testing, atomic force microscopy (AFM), and X-ray diffraction (XRD). The influencing factors, including as-deposited and annealing conditions and clay concentrations on the mechanical properties were analyzed. Results show that all of the multilayers exhibit high bonding strength between interlayers. Higher modulus and hardness of clay-based multilayers were obtained with lower clay concentrations than that with higher clay concentrations. Different relationships between the modulus and hardness and the annealing temperature exist for a specific type of clay-oxide multilayer. This work offers the basic and essential knowledge on design of clay-based nanostructured multilayers by layer-by-layer self-assembly.
RESUMEN
Ternary clay-based composite material (TCC), composed of lime, clay and sand, and usually modified with sticky rice and other organic compounds as additives, was widely used historically in Chinese construction and buildings due to its high mechanical performance. In this study, to gain an insight into the micromechanical mechanism of this cementitious material, the nanomechanical properties and volume fraction of mechanically different phases of the binder matrix are derived from the analysis of grid nanoindentation tests. Results show that there are five distinct mechanical phases, where the calcium silicate hydrate (C-S-H) and geopolymer present in the binder matrix are almost identical to those produced in ordinary Portland cement (OPC) and alkali-activated fly-ash geopolymer materials in nano-mechanical performance. The nano-mechanical behavior of calcite produced by the carbonation of lime in this binder is close to the calcite porous outer part of some sea urchin shells. Compared to OPC, the C-S-H contained in the TCC has a relatively lower ratio of indentation modulus to indentation hardness, implying a relatively lower resistance to material fracture. However, the geopolymer and calcite, at nearly the same volume content as the C-S-H, help to enhance the strength and durability of the TCC by their higher energy resistance capacity or higher strength compared to the C-S-H. Rediscovering of TCC offers a potential way to improve modern concrete's strength and durability through synergy of multi-binders and the addition of organic materials if TCC can be advanced in terms of its workability and hardening rate.
