RESUMEN
We present a thulium-doped silica fiber, featuring a depressed cladding, for applications at wavelengths below 1800 nm. The depressed cladding is used as a distributed filter suppressing amplified spontaneous emission at longer wavelengths, which helps promote emission at shorter wavelengths. We describe the fiber design process that was carried out by using a combination of numerical methods. The fiber was prepared in-house by a combination of the standard modified chemical vapor deposition method and nanoparticle doping. We demonstrate the effectiveness and tunability of ASE filtering, which is influenced by fiber bend radius and its variation.
RESUMEN
We present the development of a pair of silica-based thulium-doped fiber amplifiers working together in a broad spectral range from 1.65 µm to 2.02 µm. For the one optimized for shorter wavelengths, we designed and prepared optical fiber with a depressed cladding. We show the performance of the amplifiers achieving small-signal gain of at least 10 dB over 350 nm range from 1670 nm to 2020 nm, maximum gain of 40.7 dB with a noise figure as low as 6.45 dB and an optical signal-to-noise ratio of up to 50 dB. To the best of our knowledge, it is the first time that thulium fiber amplifiers of straightforward design without using redundant spectral filters operating efficiently in such a wide spectral region are demonstrated.
RESUMEN
An investigation on the temperature dependence of spectroscopic parameters of trivalent thulium ions is important for the design of high-power, thulium-doped fiber lasers and amplifiers. In this Letter, the thulium absorption/emission cross sections are determined in the spectral range 700-2200 nm and in the temperature range from -196°C to 300°C. The spectra are obtained from the absorption and emission measurements of a thulium-doped fiber and from measured thulium concentration profiles. Attempts were made to estimate the temperature dependence of the spectra where the measurements are not accessible. Firstly, the spectra are fitted to a multi-Gaussian model with temperature dependent parameters. Secondly, a physically motivated model of the cross section spectra is proposed and analyzed.
RESUMEN
We report on the enhancement of high harmonic generation (HHG) yield in a metasurface consisting of amorphous silicon disks in a periodic array on an insulator substrate. The structure was designed and optimized using the finite-difference time-domain method for the maximum enhancement, which reaches the factor of 20-times compared to the unstructred surface. The local field is enhanced by a broadband magnetic resonance mode allowing to use ultrashort laser pulses with Fourier transform limit down to 40 fs. Due to the anisotropic structure of the metasurface, both the local-field enhancement and the HHG yield show strong polarization anisotropy.
RESUMEN
We present the pedestal-free thulium doped silica fiber with a large nanostructured core optimized for fiber lasers. The fiber is composed of over 6 thousand thulium doped silica nanorods with a diameter of 71â nm each which form a nanostructured step-index core. We study the influence of non-continuous distribution in nanoscale active areas on gain, beam quality, and fiber laser performance. The proof-of-concept fiber is effectively single mode for wavelength above 1.8 µm. We demonstrate the performance of the fiber in a laser setup pumped at 792â nm. Single mode laser emission with a slope efficiency of 29% at quasi-continuous output power of 4 W with M2 = 1.3 at the emission spectrum 1880-1925 nm is achieved.
RESUMEN
We investigate the influence of various optical fiber fabrication processes on the fluorescence decay of RE ions commonly used in fiber lasers and amplifiers, i.e. Yb3+, Tm3+ and Ho3+. Optical fiber preforms were prepared using the MCVD method combined with Al2O3 nanoparticle doping and subjected to subsequent heat treatment processes such as preform elongation and fiber drawing. The fluorescence decay of RE ions was measured in multiple stages of optical fiber preparation: in an original preform, in an elongated preform (cane), in a standard fiber, and in an overcladded fiber. It was found that heat treatment processing of the preforms generally leads to a faster fluorescence decay, which can be explained by the diffusion of dopants and clustering of RE ions. The fiber drawing exhibited a greater effect compared to preform elongation, which was ascribed to a faster cooling rate of the process. In general, the heat treatment of RE-doped silica glass preforms leads to the decline of fluorescence decay.
RESUMEN
Laser sources emitting in the infrared range at around 2 µm are attracting great interest for a variety of applications like processing of transparent thermoplastic polymers in industry as well as plenty of applications in medicine, spectroscopy, gas sensing, nonlinear frequency conversion to the mid-infrared, to mention a few. Of late, fiber lasers compared to other kinds of lasers benefit from their all-fiber design, leading to a compact, robust, and well thermally manageable device. Particularly, thulium- and holmium-doped fiber lasers are the first choice in fiber lasers emitting light around 2 µm. In this paper, we give an overview of our recent results in the research on thulium- and holmium-doped optical fibers, fiber lasers, and related research topics in the 2-µm spectral range. In particular, we present, to our knowledge, the first results of improvement of pump absorption in double-clad fibers thanks to the fiber twist frozen during drawing. Finally, a brief demonstration of material processing by thulium all-fiber laser operating at 2 µm is presented.
RESUMEN
We experimentally compared for the first time, two techniques of optical fiber preform shaping based on the mechanical grinding and thermal CO2 laser processing from the point of the inner-cladding losses. The shaped preforms were fabricated of coreless pure silica technical rods as well as high purity silica Heraeus F300 rods and drawn them into coreless multimode fibers with various inner-cladding geometries coated with a low index fluorinated polymers. The background losses of the fibers were measured via the cut-back method and compared to the losses of the unshaped fibers with a circular cross-section. Results show that both preform-shaping techniques would induce additional losses in the inner-cladding. High surface scattering losses were observed in the mechanically-grinded fibers. On the other hand, the mechanical grinding retains the advantage of a significant reduction of attenuation peaks attributed to OH-groups that penetrated into the preform surface during the preform collapse. On the contrary, CO2 laser thermal-shaping provides the advantage of quick, fully automated shaping with smooth surface finish and induces much lower scattering losses, but it is not so effective in removing water penetrated surface layer of the preform so that OH-groups diffuse deeper towards the preform center. Additionally, laser thermal-shaping allows processing the preform to complex shapes which are more effective in scrambling cladding modes. Some of the absorption peaks of OH-groups and fluorinated polymers may be rather close to common pumping wavelengths and this should be considered in the design of the double-clad fibers and selection of proper shaping technology.
RESUMEN
Optical fibers have recently attracted a noticeable interest for biomedical applications because they provide a minimally invasive method for in vivo sensing, imaging techniques, deep-tissue photodynamic therapy or optogenetics. The silica optical fibers are the most commonly used because they offer excellent optical properties, and they are readily available at a reasonable price. The fused silica is a biocompatible material, but it is not bioresorbable so it does not decompose in the body and the fibers must be ex-planted after in vivo use and their fragments can present a considerable risk to the patient when the fiber breaks. In contrast, optical fibers made of phosphate glasses can bring many benefits because such glasses exhibit good transparency in ultraviolet-visible and near-infrared regions, and their solubility in water can be tailored by changing the chemical composition. The bioresorbability and toxicity of phosphate glass-based optical fibers were tested in vivo on male laboratory rats for the first time. The fiber was spliced together with a standard graded-index multi-mode fiber pigtail and an optical probe for in vitro pH measurement was prepared by the immobilization of a fluorescent dye on the fiber tip by a sol-gel method to demonstrate applicability and compatibility of the fiber with common fiber optics.
Asunto(s)
Fibras Ópticas , Fosfatos/química , Fosfatos/metabolismo , Animales , Concentración de Iones de Hidrógeno , Masculino , Ratas , Ratas Wistar , Dióxido de Silicio/químicaRESUMEN
Self-sweeping of laser wavelength corresponding to holmium emission near 2100 nm is reported. The sweeping occurred in ~4 nm interval with rate ~0.7 nm/s from longer towards shorter wavelengths. Origins of the selection of the sweeping direction are discussed. The laser wavelength drift with time was registered by Fourier transform infrared spectrometer. To our knowledge it is the first observation of self-swept fiber laser beyond 2000 nm.
RESUMEN
In this Letter, we demonstrate a graphene mode-locked, all-fiber Ho-doped fiber laser generating 1.3 nJ energy pulses directly from the oscillator. The graphene used as a saturable absorber was obtained via chemical vapor deposition on copper substrate and immersed in a poly(methyl methacrylate) support. The laser generated ultrashort soliton pulses at 2080 nm with bandwidth up to 6.1 nm. The influence of the output coupling ratio and the SA modulation depth on the mode-locking performance was also investigated.
RESUMEN
Results of the first experimental demonstration of the recently proposed technique for improvement of the pump absorption in double-clad fibers by their simultaneous coiling and twisting are reported. The peak absorption (14 dB) of 3-m long hexagonal thulium-doped fiber was increased by 8 dB by its simultaneous coiling and twisting. Explanation of the effect is given by numerical modelling of the pump absorption in hexagonal and panda-type double-clad fibers. Improvement of fiber laser performance was also proved. The slope efficiency increased from 19.6% of the straight fiber to 23.9% of the coiled only fiber and 29.4% of the simultaneously coiled and twisted fiber.
RESUMEN
We report on a novel mode-field adapter that is proposed to be incorporated inside tapered fused-fiber-bundle pump and signal combiners for high-power double-clad fiber lasers. Such an adapter allows optimization of signal-mode-field matching on the input and output fibers. Correspondingly, losses of the combiner signal branch are significantly reduced. The mode-field adapter optimization procedure is demonstrated on a combiner based on commercially available fibers. Signal wavelengths of 1.55 and 2 µm are considered. The losses can be further improved by using specially designed intermediate fiber and by dopant diffusion during splicing as confirmed by preliminary experimental results.
RESUMEN
A compact upconversion fiber laser operating around 810 nm is proposed using thulium-doped silica-based fiber with locally modified thulium environment by high alumina codoping. Using a comprehensive numerical model of thulium doped fiber we investigate performance of the proposed laser. Comparison with two other thulium hosts, fluoride glass and standard silica, is presented. Efficient lasing can be expected even for silica based fiber for specific ranges of the fiber and laser cavity parameters, especially when 3H4 lifetime is enhanced. With moderate pump power of 5 W at wavelength of 1064 nm, the predicted output power of the upconversion laser is about 2 W at 810 nm.
Asunto(s)
Diseño Asistido por Computadora , Tecnología de Fibra Óptica/instrumentación , Rayos Láser , Modelos Teóricos , Tulio/química , Diseño de Equipo , Análisis de Falla de EquipoRESUMEN
We present experimental demonstration of an end-pumping scheme based on splicing the multimode pump and single-mode signal fibers directly to a double-clad fiber with a tailored cross section. The method is used to pump a double-clad, erbium- and ytterbium-doped, fiber ring laser. The efficiency of the end-pumping method is tested by determining the slope efficiencies of the fiber ring laser and the fiber laser in a Fabry-Perot configuration. Comparable slope efficiencies are found when both laser configurations have similar output coupler ratios. The developed pumping scheme and double-clad fiber can find applications in cost-effective power fiber amplifiers and lasers.