Exploring the Efficiency of Algerian Kaolinite Clay in the Adsorption of Cr(III) from Aqueous Solutions: Experimental and Computational Insights.

The current study comprehensively investigates the adsorption behavior of chromium (Cr(III)) in wastewater using Algerian kaolinite clay. The structural and textural properties of the kaolinite clay are extensively characterized through a range of analytical methods, including XRD, FTIR, SEM-EDS, XPS, laser granulometry, N2 adsorption isotherm, and TGA-DTA. The point of zero charge and zeta potential are also assessed. Chromium adsorption reached equilibrium within five minutes, achieving a maximum removal rate of 99% at pH 5. Adsorption equilibrium is modeled using the Langmuir, Freundlich, Temkin, Elovich, and Dubinin-Radushkevitch equations, with the Langmuir isotherm accurately describing the adsorption process and yielding a maximum adsorption capacity of 8.422 mg/g for Cr(III). Thermodynamic parameters suggest the spontaneous and endothermic nature of Cr(III) sorption, with an activation energy of 26.665 kJ/mol, indicating the importance of diffusion in the sorption process. Furthermore, advanced DFT computations, including COSMO-RS, molecular orbitals, IGM, RDG, and QTAIM analyses, are conducted to elucidate the nature of adsorption, revealing strong binding interactions between Cr(III) ions and the kaolinite surface. The integration of theoretical and experimental data not only enhances the understanding of Cr(III) removal using kaolinite but also demonstrates the effectiveness of this clay adsorbent for wastewater treatment. Furthermore, this study highlights the synergistic application of empirical research and computational modeling in elucidating complex adsorption processes.

Oil and Organic Liquids Incorporation into Fresh Geopolymer Pastes Using Suitable Quaternary Ammonium Surfactants.

The direct incorporation of low viscosity organic liquids (OL) such as dodecane and tributylphosphate (TBP) into fresh geopolymers (GP) is difficult and generally leads to variable amounts of un-incorporated OL remaining outside the hardened geopolymer. Experimentally, it is observed that a regular torque increase during OL incorporation corresponds to a suitable dispersion of the OL in the form of fine micrometric droplets. This can be obtained for TBP and dodecane by adding a small quantity of quaternary ammoniums salts (QAs) such as cetyltrimethylammonium bromide (CTAB). Shorter alkyl chains QAs, such as hexamethyltrimethylammonium (HMTA) can also be used but with a reduced efficiency. The positive impact of CTAB is then confirmed by the Washburn capillary rise method, showing that the interactions between TBP and CTAB-modified metakaolin are weaker compared to untreated powder. Finally, it is observed that the incorporation of TBP into geopolymer slurries is much easier than the incorporation of dodecane. The low interfacial tension measured between TBP and the activating solution (around 8 mN·m -1 ), contrasting with dodecane (29 mN·m -1 ), explains that the dispersion of TBP droplets in fresh metakaolin suspensions is more efficient.

Development of a TiO2/Sepiolite Photocatalyst for the Degradation of a Persistent Organic Pollutant in Aqueous Solution.

A clay-based TiO2 nanocomposite material was synthesized by a facile method, to investigate its structure and photocatalytic efficiency. The supported TiO2 nanoparticles were generated using a sol-gel method, and subsequently, mixed with a suspension of sepiolite. The material was recovered in powder form (Mc-80) and then calcined to properly arrange the crystal lattice of the TiO2 particles for use in heterogeneous photocatalysis (Mc-80-500). A powder X-ray diffractogram of Mc-80-500 revealed a dispersion of anatase and rutile phase TiO2 particles on the clay surface, exhibiting a size in the order of 4-8 nm. TEM images of Mc-80-500 confirmed the presence of isolated TiO2 beads on the surface of the fibrous sepiolite. The specific surface area of Mc-80-500 was larger than that of raw sepiolite and that of free TiO2 nanoparticles. Mc-80-500 was found to be more efficient in heterogeneous photocatalysis compared to other TiO2 materials based on sepiolite. Total depollution of a reactive dye (Orange G) was achieved after 1 h irradiation time, which is relatively quick compared to previous reports. The photocatalyst material can be washed with distilled water without chemical additives or calcination, and can be reused several times for photocatalysis, without loss of efficiency.

Simultaneous Determination of the Chemical (kr ) and the Physical (kq ) Quenching Rate Constants of Singlet Oxygen in Aqueous Solution by the Chemiluminescence-quenching Method.

This work reports a novel and visual method for the simultaneous determination of the chemical (kr ) and the physical (kq ) quenching rate constants of singlet oxygen (1 O2 ,1 ∆g ) in aqueous media. It is based on the disruption, by a water-soluble substrate S, of the 1 O2 chemiluminescence (CL) generated by the H2 O2 /Na2 MoO4 catalytic system. A mathematical analysis of the CL signal at 1270 nm vs time provides separately the overall (kr + kq ) and the chemical (kr ) quenching rate constants. In ordinary water (H2 O), 1 O2 lifetime is short and the CL intensity is weak allowing solely the investigation of very reactive substrates for which (kr + kq ) > 3 × 106 m-1 s-1 while, in D2 O, 1 O2 lifetime is significantly longer lifetime and the CL signal is much stronger allowing the study of poorly reactive substrates for which (kr + kq ) > 4 × 105 m-1 s-1 . The method has been successfully tested on a series of anionic and nonionic water-soluble naphthalene derivatives commonly used as bio-compatible 1 O2 carriers. The obtained kr and kq values are in good agreement with the values determined by conventional techniques, namely, flash photolysis and competitive kinetics with a reference quencher.

Catastrophic Emulsion Inversion Process of Highly Viscous Isosorbide Biobased Polyester Monitoredin situ by Torque and Light Backscattering.

Highly viscous hydrophobic isosorbide biobased polyester O/W emulsions are prepared through catastrophic phase inversion. The process is followed in situ with two different methods: torque and light backscattering (LBS). Considering high viscosity of the system, only discontinuous conductivity monitoring is performed for comparison. Torque and LBS allow to highlight the emulsion inversion point (EIP) with relatively close water weight fraction values (fw≈0.20). The torque and LBS signals are rather noisy before inversion (evolution of different structures) and more smooth after phase inversion (continuous aqueous phase). Torque gives a more macroscopic information, representative of the global state of the dispersion. Consistent conductivity and torque measurements suggest indeed an inversion pathway through multiple o/W/O emulsions leading to multiple complex structures before getting continuous aqueous final emulsion. This hypothesis is confirmed with continuous LBS monitoring and microscopic observations. LBS signal seems more complete because it combines the information of conductivity and torque and allows to clearly follow in situ the inversion from the beginning to the end of the process.

Synthesis and characterization of polyampholytic aryl-sulfonated chitosans and their in vitro anticoagulant activity.

This work firstly aimed to synthesize mono- and di- sulfonic derivatives of chitosan by reductive amination reaction using respectively 2-formyl benzene sulfonic acid and 2,4 formyl benzene sulfonic acid sodium salts. The influence of the reactants molar ratio (R), aryl - substituted amino groups versus chitosan free amino groups, on the degree of substitution (DS) of both sulfonated chitosans was assessed by 1H NMR, elemental analysis, coupled conductometry-potentiometry analysis and UV spectrometry and FTIR. The influence of pH on sulfonated chitosans' properties in solution were investigated by solubility and zeta potential (ZP) studies, size exclusion chromatography equipped with MALLS detection (SEC-MALLS) and Taylor dispersion analysis (TDA). The polyampholytic character of both series was evidenced and strongly modified the solutions properties compared to chitosan. Then, the anticoagulant properties of mono- and di- sulfonic polymers were investigated by the measurement of the activated partial thromboplastin time (aPTT), Prothrombin-time (PT) and anti-(factor Xa).

Structure-interfacial properties relationship and quantification of the amphiphilicity of well-defined ionic and non-ionic surfactants using the PIT-slope method.

The Phase Inversion Temperature of a reference C10E4/n-Octane/Water system exhibits a quasi-linear variation versus the mole fraction of a second surfactant S2 added in the mixture. This variation was recently proposed as a classification tool to quantify the Hydrophilic-Lipophilic Balance (HLB) of commercial surfactants. The feasibility of the so-called PIT-slope method for a wide range of well-defined non-ionic and ionic surfactants is investigated. The comparison of various surfactants having the same dodecyl chain tail allows to rank the polar head hydrophilicity as: SO3Na⩾SO4Na⩾NMe3Br>E2SO3Na≈CO2Na⩾E1SO3Na⩾PhSO3Na>Isosorbide(exo)SO4Na≫IsosorbideendoSO4Na≫E8⩾NMe2O>E7>E6⩾Glucosyl>E5⩾Diglyceryl⩾E4>E3>E2≈Isosorbide(exo)>Glyceryl>Isosorbide(endo). The influence on the surfactant HLB of other structural parameters, i.e. hydrophobic chain length, unsaturation, replacement of Na(+) by K(+) counterion, and isomerism is also investigated. Finally, the method is successfully used to predict the optimal formulation of a new bio-based surfactant, 1-O-dodecyldiglycerol, when performing an oil scan at 25 °C.

Classification of ester oils according to their Equivalent Alkane Carbon Number (EACN) and asymmetry of fish diagrams of C10E4/ester oil/water systems.

The phase behavior of well-defined C10E4/ester oil/water systems versus temperature was investigated. Fifteen ester oils were studied and their Equivalent Alkane Carbon Numbers (EACNs) were determined from the so-called fish-tail temperature T* of the fish diagrams obtained with an equal weight amount of oil and water (f(w)=0.5). The influence of the chemical structure of linear monoester on EACN was quantitatively rationalized in terms of ester bonds position and total carbon number, and explained by the influence of these polar oils on the "effective" packing parameter of the interfacial surfactant, which takes into account its entire physicochemical environment. In order to compare the behaviors of typical mono-, di-, and triester oils, three fish diagrams were entirely plotted with isopropyl myristate, bis (2-ethylhexyl) adipate, and glycerol trioctanoate. When the number of ester bonds increases, a more pronounced asymmetry of the three-phase body of the fish diagram with respect to T* is observed. In this case, T* is much closer to the upper limit temperature Tu than to the lower limit temperature Tl of the three-phase zone. This asymmetry is suggested to be linked to an increased solubility of the surfactant in the oil phase, which decreases the surfactant availability for the interfacial pseudo-phase. As a consequence, the asymmetry depends on the water-oil ratio, and a method is proposed to determine the fw value at which T* is located at the mean value of Tu and Tl.

Optimisation of the chemical generation of singlet oxygen (1O2, 1Deltag) from the hydrogen peroxide-lanthanum(III) catalytic system using an improved NIR spectrometer.

A near-IR chemiluminescence spectrometer designed to study chemical sources of singlet oxygen ((1)O(2), (1)Delta(g)), was built by coupling a reactor compartment to a nitrogen-cooled Ge diode through a bundle of optical fibres. This device was used to optimise the generation of (1)O(2) from the hydrogen peroxide-lanthanum(iii) catalytic system. The reaction kinetics were studied with a 2(3)3(3)//12 screening experimental design comprising twelve experiments. The influence of six factors was examined: the nature of the lanthanum salt (hydroxide, oxide or nitrate) and its concentration (0.05 or 0.1 mol L(-1)), the pH value (5, 7 or 9), the concentration of H(2)O(2) (0.5, 1 or 2 mol L(-1)), the temperature (20 or 30 degrees C) and the concentration of EDTA (0 or 5 mmol L(-1)). Two responses were measured: the rate of H(2)O(2) disproportionation and the intensity of the luminescence of (1)O(2) at 1270 nm. The essential factor is the nature of the lanthanum salt since La(NO(3))(3) induces the disproportionation of H(2)O(2) about 60 x faster than La(2)O(3) or La(OH)(3). Other influencing factors are the pH value, the concentration of H(2)O(2), the temperature and the concentration of the lanthanum salt whereas the concentration of EDTA has no effect on the reaction. The catalytic activity of La(NO(3))(3) was then investigated in further detail by studying the influence of two factors (pH and [H(2)O(2)]) thanks to a Doehlert design.

Solid state and solution 43Ca NMR of calcium peroxides involved in the disproportionation of hydrogen peroxide by calcium hydroxide.

In order to get some insight into the mechanism of the disproportionation of hydrogen peroxide catalyzed by calcium hydroxide, 43Ca NMR spectra of enriched samples of calcium peroxides and of their precursors have been studied in both solution and solid state. This study demonstrates that no well-defined peroxidized calcium species are formed in solution, showing that the catalytic role of calcium is likely restricted to the solid state. Most of the calcium compounds that could be involved in the catalytic process have been investigated with solid state NMR. The shift and quadrupolar parameters of Ca(OH)2, CaO2.8H2O and CaO2.2H2O2 are reported for the first time. These parameters are different enough to allow the quantitative analysis of a complex mixture of these compounds by NMR.

Reversible binding of oxygen to aromatic compounds.

Many polycyclic aromatic hydrocarbons are able to trap singlet oxygen (1)O(2). Some of the endoperoxides, thus obtained, exhibit the exceptional feature of releasing oxygen, frequently in the excited singlet state, under heating or UV irradiation. In this Account, we provide a short summary of the present knowledge on these endoperoxides: preparation and thermal and photolytic decomposition, with a special emphasis on the structural requirements to favor cycloreversion. The profitable use of this property in the development of highly reversible photochromic systems and of specific sources or traps of (1)O(2) in aqueous media is also described.

Calcium peroxide diperoxohydrate as a storable chemical generator of singlet oxygen for organic synthesis.

Calcium peroxide diperoxohydrate (CaO(2).2H(2)O(2)) is an environmentally friendly generator of singlet oxygen ((1)O(2), (1)Delta(g)) that can be used in organic synthesis as an alternative to the regular photochemical method. This compound produces (1)O(2) in various solvents and can be easily recovered by filtration for further regeneration. Both monitoring of (1)O(2) luminescence at 1270 nm and specific trapping have shown that CaO(2).2H(2)O(2) can be stored for several days at -80 degrees C and that the yield of (1)O(2) is equal to 25%. Oxidation of typical organic substrates in methanol or THF through [4 + 2] or [2 + 2] cycloaddition and ene reaction have been carried out on a preparative scale with total conversion and selectivity.