Focused electron beam induced deposition as a tool to create electron vortices.

Focused electron beam induced deposition (FEBID) is a microscopic technique that allows geometrically controlled material deposition with very high spatial resolution. This technique was used to create a spiral aperture capable of generating electron vortex beams in a transmission electron microscope (TEM). The vortex was then fully characterized using different TEM techniques, estimating the average orbital angular momentum to be ∼0.8ℏ per electron with almost 60% of the beam ending up in the ℓ=1 state.

Direct writing of CoFe alloy nanostructures by focused electron beam induced deposition from a heteronuclear precursor.

Recently, focused electron beam-induced deposition has been employed to prepare functional magnetic nanostructures with potential in nanomagnetic logic and sensing applications by using homonuclear precursor gases like Fe(CO)5 or Co2(CO)8. Here we show that an extension towards the fabrication of bi-metallic compounds is possible by using a single-source heteronuclear precursor gas. We have grown CoFe alloy magnetic nanostructures from the HFeCo3(CO)12 metal carbonyl precursor. The compositional analysis indicates that the samples contain about 80 at% of metal and 10 at% of carbon and oxygen. Four-probe magnetotransport measurements are carried out on nanowires of various sizes down to a width of 50 nm, for which a room temperature resistivity of 43 µΩcm is found. Micro-Hall magnetometry reveals that 50 nm × 250 nm nanobars of the material are ferromagnetic up to the highest measured temperature of 250 K. Finally, the transmission electron microscopy (TEM) microstructural investigation shows that the deposits consist of a bcc Co-Fe phase mixed with a FeCo2 O4 spinel oxide phase with nanograins of about 5 nm diameter.

Electron nanoprobe induced oxidation: a simulation of direct-write purification.

Electron beam direct-write has recently taken a large step forward with the advent of methods to purify deposits. This development has opened the door for future direct-write device prototyping and editing. In one such approach, an additional beam scanning procedure removes carbonaceous impurities via oxidation from metal-carbon deposits (e.g., PtC5) in the presence of H2O or O2 after deposition. So far, critical aspects of the oxidation reaction remain unclear; experiments reveal clearly that electron stimulated oxidation drives the process yet it is not understood why H2O purifies by a bottom-up mechanism while O2 purifies from the top-down. The simulation results presented here suggest that the chemisorption of dissolved O2 at buried Pt nanoparticle surfaces controls purification in the top-down case while both the high relative solubility coupled with weak physisorption of H2O explains the bottom-up process. Crucial too is the role that the carbonaceous contaminant itself has on the dissolution and diffusion of O2 and H2O. These results pave the way for simulation driven experiments where (1) the transient densification of the deposit can be accounted for in the initial deposit design stage and (2) the deposition and purification steps can be combined.

Post-growth purification of Co nanostructures prepared by focused electron beam induced deposition.

In the majority of cases nanostructures prepared by focused electron beam induced deposition (FEBID) employing an organometallic precursor contain predominantly carbon-based ligand dissociation products. This is unfortunate with regard to using this high-resolution direct-write approach for the preparation of nanostructures for various fields, such as mesoscopic physics, micromagnetism, electronic correlations, spin-dependent transport and numerous applications. Here we present an in situ cleaning approach to obtain pure Co-FEBID nanostructures. The purification procedure lies in the exposure of heated samples to a H2 atmosphere in conjunction with the irradiation by low-energy electrons. The key finding is that the combination of annealing at 300 °C, H2 exposure and electron irradiation leads to compact, carbon- and oxygen free Co layers down to a thickness of about 20 nm starting from as-deposited Co-FEBID structures. In addition to this, in temperature-dependent electrical resistance measurements on post-processed samples we find a typical metallic behavior. In low-temperature magnetoresistance and Hall effect measurements we observe ferromagnetic behavior.

Room-temperature high-frequency transport of dirac fermions in epitaxially grown Sb2Te3- and Bi2Te3-based topological insulators.

We report on the observation of photogalvanic effects in epitaxially grown Sb2Te3 and Bi2Te3 three-dimensional (3D) topological insulators (TI). We show that asymmetric scattering of Dirac fermions driven back and forth by the terahertz electric field results in a dc electric current. Because of the "symmetry filtration" the dc current is generated by the surface electrons only and provides an optoelectronic access to probe the electron transport in TI, surface domains orientation, and details of electron scattering in 3D TI even at room temperature.

Chemical degradation and morphological instabilities during focused ion beam prototyping of polymers.

Focused ion beam processing of low melting materials, such as polymers or biological samples, often leads to chemical and morphological instabilities which prevent the straight-forward application of this versatile direct-write structuring method. In this study the behaviour of different polymer classes under ion beam exposure is investigated using different patterning parameters and strategies with the aim of (i) correlating local temperatures with the polymers' chemistry and its morphological consequences; and (ii) finding a way of processing sensitive polymers with lowest chemical degradation while maintaining structuring times. It is found that during processing of polymers three temperature regimes can be observed: (1) at low temperatures all polymers investigated show stable chemical and morphological behaviour; (2) very high temperatures lead to strong chemical degradation which entails unpredictable morphologies; and (3) in the intermediate temperature regime the behaviour is found to be strongly material dependent. A detailed look reveals that polymers which rather cross-link in the proximity of the beam show stable morphologies in this intermediate regime, while polymers that rather undergo chain scission show tendencies to develop a creeping phase, where material follows the ion beam movement leading to instable and unpredictable morphologies. Finally a simple, alternative patterning strategy is suggested, which allows stable processing conditions with lowest chemical damage even for challenging polymers undergoing chain scission.

Development of an itraconazole-loaded nanostructured lipid carrier (NLC) formulation for pulmonary application.

Itraconazole-loaded NLC for pulmonary application were developed. In Precirol ATO 5 and oleic acid Itraconazole had the highest solubility. The solid lipid and the oil were mixable in a ratio 9:1 possessing a melting point above body temperature. 0.4% Itraconazole was dissolved in this lipid blend. Eumulgin SLM 20 was the stabilizer with the highest affinity to the lipid blend used as particle matrix. 2.5% Eumulgin SLM 20 was sufficient to obtain NLC with a narrow particle size distribution and sufficient stability. The tonicity of the formulation was adjusted with glycerol. Sterility was obtained by autoclaving. Neither the addition of glycerol nor autoclaving had an influence on the particle size and the zeta potential of Itraconazole-loaded NLC. SEM images showed spherical particles confirming the particle size measured by light scattering techniques. An entrapment efficiency of 98.78% was achieved. Burst release of Itraconazole from the developed carrier system was found. Itraconazole-loaded NLC possessed good storage stability. Nebulizing Itraconazole-loaded NLC with a jet stream and an ultrasonic nebulizer had no influence on the particle size and the entrapment efficiency of Itraconazole in the particle matrix, being a precondition for pulmonary application.

Note: On the deconvolution of Kelvin probe force microscopy data.

In Kelvin probe force microscopy (KPFM) proper interpretation of the data is often difficult because the measured surface potential is affected by the interaction of the cantilever with the sample. In this work, the tip's interaction with a modeled surface potential distribution was simulated, leading to a calculated KPFM image. Although simplified, the calculation is capable of showing the influence of the cantilever in the correct qualitative manner, proven by a comparison with experimental data. Additionally, a deconvolution was performed on the simulated image, showing that for simple geometries revealing the "real" surface potential data is possible in principle.

The influence of beam defocus on volume growth rates for electron beam induced platinum deposition.

Electron beam induced deposition (EBID) is a versatile method for the controlled fabrication of conducting, semi-conducting and non-conducting structures down to the nanometer scale. In contrast to ion beam induced deposition, EBID processes are free of sputter effects, ion implantation and massive heat generation; however, they have much lower deposition rates. To push the deposition efficiency further towards its intrinsic limits, the individual influences of the process parameters have to be explored. In this work a platinum pre-cursor is used for the deposition of conducting nanorods on highly oriented pyrolytic graphite. The study shows the influence of a beam defocus during deposition on the volume growth rates. The temporal evolution of volume growth rates reveals a distinct maximum which is dependent on the defocus introduced, leading to an increase of deposited volumes by a factor 2.5 after the same deposition times. The observed maximum is explained by an increasing and saturating electron yield contributing to the final deposition process and constantly decreasing diffusion abilities of the pre-cursor molecules toward the tip of the nanorods, which is further supported by dwell time experiments.

[Quality of life and pain in hospitalized geriatric patients]. / Lebensqualität und Schmerz bei Patienten einer medizinisch-geriatrischen Abteilung.

BACKGROUND: To determine objective and subjective indications of quality of life in hospitalized geriatric patients. METHODS: Data were collected on 267 items using standardized interviews of 90 patients, including B-L and SF-36. RESULTS: In comparison to the control population, geriatric patients have worse SF-36 values; 91% have pain, and 63% depression and elevated B-L values. Pain therapy is usually with non-opiates and with warm/cold physical therapies. CONCLUSION: Pain therapy in the geriatric population surveyed does not reach the same standard as is usually offered to hospitalized medical and surgical patients.

Soft tissue and cancellous bone reaction to the implantation of novel biodegradable pins and plates in rabbits.

Biodegradable implants for osteosynthesis have had insufficient strength and a fast degradation rate. We produced a polymer based lactide to increase the molecular weight and strength of the implant and delay the degradation rate. This novel fiber-reinforced material in the form of plates and pins was tested in vitro for mechanical performance and in vivo in a neutral mechanical environment to assess biocompatibility. 21 rabbits with implants in the tibia and femoral condyles were killed at 1, 6, 12 months after implantation. Only a mild foreign-body reaction was observed and the implant was encapsulated by a thin 0.8-1.6 mm layer of connective tissue. Only a few lymphocytes and giant cells were detected in the early stages, dense fibroblasts in the middle stage, and giant cells clearing material particles in the late stage. In conclusion, the novel fiber-reinforced polymer based on polylactides was found mechanically superior to former degradable implants and biocompatible, showing no late inflammatory tissue response.