Improved resolution of fluoroquinolones using cetyltrimethyl ammonium bromide-micellar electrokinetic chromatography and its application to residue analysis in surface water.

A simple micellar electrokinetic chromatography (MEKC), using cetyltrimethyl ammonium bromide (CTAB) as micelles, for the determination of ciprofloxacin (CIP), enrofloxacin (ENR), norfloxacin (NOR) and ofloxacin (OFL) residues in surface water was developed. Peak Master was used for predicting amounts of analyte ionic forms to reduce numbers of tedious experiments in optimizing the analyte capacity factors. A baseline separation (Rs > 2.8) of the analytes was achieved in 7 min using 15 mM sodium dihydrogen phosphate (pH 6.0) containing 3 mM CTAB and a capillary with an effective length of 56.0 cm. A negative polarity voltage of 20 kV was used to enable the migration of the cationic micelles toward the detection site. The method shows good linearity in a range of 5 and 20 µg mL-1 and precision (%RSD < 6.45). Percent recoveries of the method were in a range of 65.1-88.7%. The limits of detection and quantitation were in the ranges of 1-2 and 3-5 µg mL-1, respectively. Two steps sample clean-up and preconcentration of surface water samples by hydrophilic-lipophilic balance and fluoroquinolone-molecularly imprinted polymer were advantageous for removal of humic acids and enabling the detection of fluoroquinolone residues in the samples. Finally, the method was applied for fluoroquinolone residues analysis of surface water in Thailand.

Brompheniramine as a novel probe for indirect UV detection and its application for the capillary electrophoresis of adamantane drugs.

Brompheniramine, an antihistamine drug, was employed as a novel UV probe for capillary electrophoresis with indirect UV detection of adamantane drugs (memantine, amantadine, and rimantadine). The probe possesses high molar absorptivity of 24 × 103 L/mol cm at 6 mM, which enables the measurement of these nonchromophore analytes without derivatization. The simple background electrolyte (10 mM sodium dihydrogen phosphate (pH 5.0) containing 5 mM brompheniramine and 6 mM ß-cyclodextrin) provided the separation of the analytes in a short time (7.5 min). Under these conditions, brompheniramine had similar mobility to that of the analyte ions resulting in symmetric peaks with minimal electrodispersion. The analytes displace the probe at a one-to-one ratio with transfer values close to unity. ß-Cyclodextrin played a role in the resolution of the structurally similar adamantane derivatives. Method validation showed good linearity (r2  > 0.98), precision (%RSD ≤ 3.30), and accuracy (recoveries ranging from 98 to 109%). The proposed method was successfully applied to determine the adamantane content in pharmaceutical products.

Fluorescent labelling of ciprofloxacin and norfloxacin and its application for residues analysis in surface water.

Sensitivity enhancement for residue analysis of ciprofloxacin and norfloxacin in surface water was performed by liquid chromatography with fluorescent detection (LC-FD). Labelling of both drugs were studied with fluorescent probes (e.g. Nile blue perchlorate (NBP) and 4- (N,N-Dimethylaminosulfonyl)-7-(N-chloroformylmethyl-N-methylamino)-2,1,3-benzoxadiazole (DBD-COCl). Factors affecting the derivatization (e.g. stoichiometric ratios, reaction time and base catalysts) were optimized. The derivatization was achieved in 15min using a stoichiometric ratio between the substrate and DBD-COCl of 1:3, whereas NBP gave unsatisfactory results. Separation of the derivatives by LC was achieved (resolution (RS) > 1.8) on a C8 column using a mobile phase consisting of 50mM formic acid and acetonitrile (ACN) (68:32% v/v) in 20min. The method was linear (r(2) > 0.99) in a range of 200-2,000µg/L, precise (%RSD < 9.17) and accurate (%recovery of 102.5-122.2%) for the determination of the derivatives. The uses of fluoroquinolone molecularly imprinted polymer in conjunction with hydrophilic-lipophilic balance sorbents demonstrated an efficient procedure for sample pre-concentration and clean-up for water sample resulting in the improved percent recovery. Applications of the proposed method was shown in surface water samples in Thailand.

Stability indicating MEKC method for the determination of gliclazide and its specified impurities.

A stability indicating-micellar electrokinetic chromatography method was developed and validated for the determination of gliclazide (GCZ) and its specified impurities, gliclazide impurities B (GZB) and F (GZF) in bulk and tablets. The analytes were well separated (Rs>2.1) in 5 min using 10mM phosphate buffer (pH 7.0) containing 15 mM sodium dodecyl sulfate on a fused-silica capillary with an effective length of 40 cm and an inner diameter of 50 µm, injection at 50 mbar for 5s, temperature of 25°C, applied voltage of 20 kV and photodiode array detection at 225 nm. The method showed good linearity (r(2)>0.99, in the ranges of 128-192, 20-60 and 10-50 µg/mL for GCZ, GZB and GZF, respectively) and precision (%RSD for intra- and inter-day precision of less than 2.00%, n=3) for all compounds. Accuracy represented as %recovery was between 99.1 and 100.1% with %RSDs of less than 0.59% (n=3). Limits of detection and quantitation were less than 40 and 120 µg/mL, respectively. The method was robust with %RSDs of migration time and peak areas of less than 1.36% (n=9), when buffer and separating voltage were altered around the optimal values. Stress tests showed that GCZ was stable in alkaline hydrolysis both at room and elevated temperature. However, GCZ degraded under acid and neutral hydrolysis and oxidation condition. Elevated temperature and exposure to sunlight accelerated GCZ degradation and formation of GZB and an unknown degradation product. Stability profiles and degradation kinetics of GCZ could be established using the MEKC method. In addition, the method could be used for assay of GCZ in raw material and commercial tablets and results revealed that contents of GCZ in all samples were within the pharmacopeia limit. No degradation products, especially GZB and GZF, were observed in the investigated samples.

Development and validation of an ion-exchange chromatography method for heparin and its impurities in heparin products.

An anion-exchange liquid chromatography method for the determination of heparin and its impurities (dermatan sulfate and oversulfated chondroitin sulfate) was developed using chemometric-assisted optimization, including multivariate experimental design and response surface methodology. The separation of heparin, dermatan sulfate, and oversulfated chondroitin sulfate (Rs above 2.0) was achieved on a Dionex RF IC IonPac AS22 column with a gradient elution of 10-70% of 2.5 M sodium chloride and 20 mM Tris phosphate buffer (pH 2.1) at a flow rate of 0.6 mL/min and UV detection at 215 nm. Method validation shows good linearity (r > 0.99), acceptable precision (%relative standard deviations <11.4%) and trueness (%recovery of 92.3-103.9%) for all analytes. The limits of detection for dermatan sulfate and oversulfated chondroitin sulfate are equivalent to 0.11% w/w (10.5 µg/mL) and 0.07% w/w (7.2 µg/mL), while the limits of quantification are 0.32% w/w (31.5 µg/mL) and 0.22% w/w (22.0 µg/mL) relative to heparin, respectively. The method is specific for heparin, dermatan sulfate, and oversulfated chondroitin sulfate without interference from mobile phase and sample matrices and could be used for accurate quantitation the drug and its impurities in a single run. Applications of the method reveal contents of heparin between 90.3 and 97.8%. Dermatan sulfate and oversulfated chondroitin sulfate were not detected in any of the real-life samples.

Simultaneous analysis of metformin and cyanoguanidine by capillary zone electrophoresis and its application in a stability study.

A capillary zone electrophoresis method was established for stability study of metformin (MET). MET and cyanoguanidine (CGN; a major degradation product) were well separated (with a resolution of 38.9) in 40 mM citrate buffer (pH 6.7) using a fused-silica capillary with an effective length of 60 cm and an inner diameter of 50 µm, injection at 50 mbar for 5 s at 30°C with an applied voltage of 15 kV and diode array detection at 214 nm. Method validation showed good linearity (r(2) > 0.99), precision (%RSDs < 1.98%), and accuracy (%recovery between 98.3 and 100.9%). Limits of detection and quantification were <30 and 100 µg/mL, respectively. The method was robust upon alteration of pH and voltage (%RSDs < 1.99%). Stability profiles of metformin from 11 stress conditions and the degradation kinetics could be established, using the simple capillary zone electrophoresis system. A mechanism for the degradation of MET was also proposed. MET was stable in neutral hydrolysis, but degraded under alkaline hydrolysis and oxidation. Under both conditions, CGN was quantified as the degradation product. An assay of MET in raw material and tablets showed that content of the drugs in all samples met the requirements of pharmacopeias and CGN was not detected.

Rapid analysis of alkylphosphonate drugs by capillary zone electrophoresis using indirect ultraviolet detection.

A rapid capillary electrophoretic method for the analysis of three alkylphosphonate drugs (i.e. fosfomycin disodium (FOS), clodronate disodium (CLO) and alendronate sodium (ALN)) was developed by using multiple probe BGE and indirect UV detection. BGE containing 30 mM benzoic acid, 5 mM salicylic acid and 0.5 mM CTAB (pH 3.8), temperature of 30 degrees C, applied voltage of -30 kV and detection at 220 nm provided baseline separation of all analytes (resolution (R)>2.2) in 3.2 min. EOF reversal by addition of CTAB and negative voltage polarity leading to the co-EOF flow and short analysis time. Two probe BGE greatly improved peak symmetry. The method showed good linearity (r(2)>0.999 in ranges of 20-1000 microg/mL for FOS, 100-1000 microg/mL for CLO and 100-750 microg/mL for ALN) repeatablitiy (RSD<2.15%), recovery (99.3-101.1%) and sensitivity (LOD<50 microg/mL). Freshly prepared BGE and sample solutions are essential for the method precision and accuracy. This new method can be utilized for routine analysis of FOS, CLO and ALN in dosage forms because of its efficiency, reliability, speed and simplicity.