A Comprehensive Study of a Novel Explosively Hardened Pure Titanium Alloy for Medical Applications.

Pure titanium is gaining increasing interest due to its potential use in dental and orthopedic applications. Due to its relatively weak mechanical parameters, a limited number of components manufactured from pure titanium are available on the market. In order to improve the mechanical parameters of pure titanium, manufacturers use alloys containing cytotoxic vanadium and aluminum. This paper presents unique explosive hardening technology that can be used to strengthen pure titanium parameters. The analysis confirms that explosive induced α-ω martensitic transformation and crystallographic anisotropy occurred due to the explosive pressure. The mechanical properties related to residual stresses are very nonuniform. The corrosion properties of the explosive hardened pure titanium test do not change significantly compared to nonhardened titanium. The biocompatibility of all the analyzed samples was confirmed in several tests. The morphology of bone cells does not depend on the titanium surface phase composition and crystallographic orientation.

Influence of Strain Rates during Severe Plastic Strain Processes on Microstructural and Mechanical Evolution in Pure Zinc.

The study presents an analysis of the influence of the plastic strain rate on the mechanical and structural properties of pure zinc. Thanks to the use of unconventional methods of plastic processing, the process of the equal channel angular pressing (ECAP) and the process of hydrostatic extrusion (HE), the tests were performed in a wide range of plastic strain rates, between 0.04 s-1 and 170 s-1. Plastic strain rate changes were carried out in the course of the significant plastic strain processes, and not on previously deformed samples. All tests were carried out at a constant value of plastic strain rate, ε ~ 2. A strong influence of the plastic strain rate on changes in the microstructure in zinc was observed during the tests. For the rates in the range of 0.04 s-1 to 0.53 s-1 its bimodal nature was observed, and in the range of 7 s-1 to 170 s-1 high homogeneity and evenness of grains related to the processes of continuous dynamic recrystallization was noticed. The effect of the strong homogenization of the microstructure was the increase in mechanical properties, yield point and tensile strength to the maximum values of UTS = 194 MPa, YS = 145 MPa at a strain rate of 170 s-1. Compared to the material with a bimodal microstructure, an over seven-fold increase in the elongation value was observed.

Mechanical Reinforcement of Polyamide 6 by Cold Hydrostatic Extrusion.

This paper presents the effect of severe plastic deformation obtained using the cold hydrostatic extrusion (HE) method on the mechanical and structural properties of polyamide 6 (PA6). As a result of the plastic strain, a significant increase in ultimate tensile strength and tensile modulus were observed. Tensile strength rose by almost 500%, up to the level of 508 MPa, whereas the tensile modulus rose by about 65%. Flexural modulus increase was also observed to 3230 MPa, i.e., by approx. 160%. As a result of high plastic deformation, the structure of the polyamide 6 changed significantly, as evidenced by its fibrous nature as presented in the results of the scanning electron microscopy inspection (SEM). The surface quality of products investigated was tested using profilometry.

Microstructural Investigation of a Friction-Welded 316L Stainless Steel with Ultrafine-Grained Structure Obtained by Hydrostatic Extrusion.

The paper presents the microstructural investigation of a friction-welded joint made of 316L stainless steel with an ultrafine-grained structure obtained by hydrostatic extrusion (HE). Such a plastically deformed material is characterized by a metastable state of energy equilibrium, increasing, among others, its sensitivity to high temperatures. This feature makes it difficult to weld ultra-fine-grained metals without losing their high mechanical properties. The use of high-speed friction welding and a friction time of <1 s reduced the scale of the weakening of the friction joint in relation to result obtained in conventional rotary friction welding. The study of changes in the microstructure of individual zones of the friction joint was carried out on an optical microscope (OM), scanning electron microscope (SEM), transmission electron microscope (TEM) and electron backscattered diffraction (EBSD) analysis system. The correlation between the microstructure and hardness of the friction joint is also presented. The heat released during the high-speed friction welding initiated the process of dynamic recrystallization (DRX) of single grains in the heat-affected zone (HAZ). The additional occurrence of strong plastic deformations (in HAZ) during flash formation and internal friction (in the friction weld and high-temperature HAZ) contributed to the formation of a highly deformed microstructure with numerous sub-grains. The zones with a microstructure other than the base material were characterized by lower hardness. Due to the complexity of the microstructure and its multifactorial impact on the properties of the friction-welded joint, strength should be the criterion for assessing the properties of the joint.