Development of a High-Sensitivity Acoustic Sensor Based on Grating Interferometer Combined with Glass Diaphragm.

In this study, based on the principle of grating interferometer-based acoustic sensors, design guidelines for the grating interferometric module were obtained and analyzed considering various factors in order to obtain high sensitivity, and a glass-based grating interference component and its acoustic sensor device were developed. The key parameters of the grating interference structure were extracted, and their effects on the acoustic response sensitivity were quantified for multiple mechanisms. For the development of the acoustic sensor, the grating-on-convex-platform structure and the micromachining processes of the glass-based components were designed and developed. The developed acoustic sensor samples achieved high sensitivity. In particular, the sample suitable for low-frequency application obtained a sensitivity of 0.776 V/Pa @ 1 kHz, and the spectrum of its sensitivity was flat from 50 Hz to 8 Hz with a deviation less than 1.5 dB and a sensitivity of 0.408 V/Pa @ 20 Hz.

Fiber-optic bionic microphone based compact sound source localization system with extended directional range.

Traditional sound source localization (SSL) systems based on electret condenser microphone arrays are bulky because their localization accuracy depends on the size of the array. Inspired by the hearing mechanism of the parasitic fly Ormia ochracea, the localization accuracy of miniature bionic SSL devices breaks through the limitations of device size, but their ability to localize low-frequency sound sources over a wide angular range remains a challenge. In this work, a compact low-frequency SSL system with an extended directional range was prepared using two bionic micro-electro-mechanical system diaphragm based fiber-optic microphones, which form a non-coplanar array with a size of Φ44 mm × 13 mm. An algorithm for quantifying the azimuthal angle of a sound source is established for the prepared SSL system. Simulation and experimental results show that the prepared SSL system is capable of determining the propagation direction of acoustic signals with a frequency of less than 1 kHz in the azimuthal range from -90° to 90°, with a linear response in the range from -70° to 70°, and an angular measurement accuracy of the system within the range of ±7°.

Analysis of tissue-substrate adhesion by hyperspectral surface plasmon resonance microscopy.

The preparation of histology slides is a critical step in histopathology, and poor-quality histology slides with weak adhesion of tissue sections to the substrate often affect diagnostic accuracy and sometimes lead to diagnostic failure due to tissue section detachment. This issue has been of concern and some methods have been proposed to enhance tissue-substrate adhesion. Unfortunately, quantitative analysis of the adhesion between tissue sections and glass slides is still challenging. In this work, the adhesion of mouse brain tissue sections on gold-coated glass slides was analyzed using a laboratory-fabricated hyperspectral surface plasmon resonance microscopy (HSPRM) system that enabled single-pixel spectral SPR sensing and provided two-dimensional (2D) distribution of resonance wavelengths (RWs). The existence of the nanoscale water gap between the tissue section and the substrate was verified by fitting the RW measured in each pixel using the five-layer Fresnel reflection model. In addition, a 2D image of the tissue-substrate adhesion distance (AD) was obtained from the measured 2D distribution of RWs. The results showed that tissue-substrate AD was 20-35 nm in deionized water and 4-24 nm in saline solution. The HSPRM system used in this work has a wide wavelength range of 400-1000 nm and can perform highly sensitive and label-free detection over a large dynamic detection range with high spectral and spatial resolutions, showing significant potential applications in stain-free tissue imaging, quantitative analysis of tissue-substrate adhesion, accurate identification of tumor cells, and rapid histopathological diagnosis.

Lithium Niobate Electro-Optic Modulation Device without an Overlay Layer Based on Bound States in the Continuum.

Electro-optic modulation devices are essential components in the field of integrated optical chips. High-speed, low-loss electro-optic modulation devices represent a key focus for future developments in integrated optical chip technology, and they have seen significant advancements in both commercial and laboratory settings in recent years. Current electro-optic modulation devices typically employ architectures based on thin-film lithium niobate (TFLN), traveling-wave electrodes, and impedance-matching layers, which still suffer from transmission losses and overall design limitations. In this paper, we demonstrate a lithium niobate electro-optic modulation device based on bound states in the continuum, featuring a non-overlay structure. This device exhibits a transmission loss of approximately 1.3 dB/cm, a modulation bandwidth of up to 9.2 GHz, and a minimum half-wave voltage of only 3.3 V.

A Grating Interferometric Acoustic Sensor Based on a Flexible Polymer Diaphragm.

This study presents a grating interferometric acoustic sensor based on a flexible polymer diaphragm. A flexible-diaphragm acoustic sensor based on grating interferometry (GI) is proposed through design, fabrication and experimental demonstration. A gold-coated polyethylene terephthalate diaphragm was used for the sensor prototype. The vibration of the diaphragm induces a change in GI cavity length, which is converted into an electrical signal by the photodetector. The experimental results show that the sensor prototype has a flat frequency response in the voice frequency band and the minimum detectable sound pressure can reach 164.8 µPa/√Hz. The sensor prototype has potential applications in speech acquisition and the measurement of water content in oil. This study provides a reference for the design of optical interferometric acoustic sensor with high performance.

Temperature-robust optical microphone with a compact grating interferometric module.

The high demand for advanced acoustic sensors has prompted optical microphones to become a current research hotspot; this is especially the case in light of the performance of existing electroacoustic microphones having reached the ceiling. In this work, a thermally stable optical microphone has been developed for sensitive detection of low-frequency acoustic signals. The microphone was prepared using a prestressed nickel diaphragm and a compact grating interferometric module. The adjacent surfaces of the diaphragm and grating form a short Fabry-Perot cavity, which makes the microphone robust to ambient temperature fluctuation due to the reduced thermal drift of its operating point relative to the quadrature point of the interferometer. The cavity length-operating wavelength relationship of the microphone operating at the quadrature point was obtained. The performance of the prepared microphone was tested using various methods. Experimental results show that the microphone enables stable operation at the quadrature point over a wide range of temperatures from 0°C to 60°C with low signal distortion and high sensitivity. The response of the prepared optical microphone to low-frequency drone noise was measured and compared with that obtained with a commercial electret condenser microphone.

Prototype Optical Bionic Microphone with a Dual-Channel Mach-Zehnder Interferometric Transducer.

A prototype optical bionic microphone with a dual-channel Mach-Zehnder interferometric (MZI) transducer was designed and prepared for the first time using a silicon diaphragm made by microelectromechanical system (MEMS) technology. The MEMS diaphragm mimicked the structure of the fly Ormia Ochracea's coupling eardrum, consisting of two square wings connected through a neck that is anchored via the two torsional beams to the silicon pedestal. The vibrational displacement of each wing at its distal edge relative to the silicon pedestal is detected with one channel of the dual-channel MZI transducer. The diaphragm at rest is coplanar with the silicon pedestal, resulting in an initial phase difference of zero for each channel of the dual-channel MZI transducer and consequently offering the microphone strong temperature robustness. The two channels of the prototype microphone show good consistency in their responses to incident sound signals; they have the rocking and bending resonance frequencies of 482 Hz and 1911 Hz, and their pressure sensitivities at a lower frequency exhibit an "8"-shaped directional dependence. The comparison indicates that the dual-channel MZI transducer-based bionic microphone proposed in this work is advantageous over the Fabry-Perot interferometric transducer-based counterparts extensively reported.

Optical metasurfaces for multiplex high-performance grating-type structural colors.

Optical metasurfaces provide a significant approach for the production of structural colors due to their excellent optical control abilities. Herein, we propose trapezoidal structural metasurfaces for achieving multiplex grating-type structural colors with high comprehensive performance originating from the anomalous reflection dispersion in the visible band. Single trapezoidal metasurfaces with different x-direction periods can tune the angular dispersion regularly from 0.036 rad/nm to 0.224 rad/nm to generate various structural colors, and composite trapezoidal metasurfaces with three kinds of combinations can achieve multiplex sets of structural colors. The brightness can be controlled by adjusting the distance between the trapezoids in a pair accurately. The designed structural colors have higher saturation than traditional pigmentary colors, whose excitation purity can reach 1.00. The gamut is about 158.1% of the Adobe RGB standard. This research has application potential in ultrafine displays, information encryption, optical storage, and anti-counterfeit tagging.

Miniature Fourier Transform Spectrometer Based on Thin-Film Lithium Niobate.

A miniature Fourier transform spectrometer is proposed using a thin-film lithium niobate electro-optical modulator instead of the conventional modulator made by titanium diffusion in lithium niobate. The modulator was fabricated by a contact lithography process, and its voltage-length and optical waveguide loss were 2.26 V·cm and 1.01 dB/cm, respectively. Based on the wavelength dispersion of the half-wave voltage of the fabricated modulator, the emission spectrum of the input signal was retrieved by Fourier transform processing of the interferogram, and the analysis of the experimental data of monochromatic light shows that the proposed miniaturized FTS can effectively identify the input signal wavelength.

Low-loss, ultracompact n-adjustable waveguide bends for photonic integrated circuits.

Countless waveguides have been designed based on four basic bends: circular bend, sine/cosine bend, Euler bend (developed in 1744) and Bezier bend (developed in 1962). This paper proposes an n-adjustable (NA) bend, which has superior properties compared to other basic bends. Simulations and experiments indicate that the NA bends can show lower losses than other basic bends by adjusting n values. The circular bend and Euler bend are special cases of the proposed NA bend as n equals 0 and 1, respectively. The proposed bend are promising candidates for low-loss compact photonic integrated circuits.

Multichannel Flexible Pulse Perception Array for Intelligent Disease Diagnosis System.

Pressure sensors with high sensitivity, a wide linear range, and a quick response time are critical for building an intelligent disease diagnosis system that directly detects and recognizes pulse signals for medical and health applications. However, conventional pressure sensors have limited sensitivity and nonideal response ranges. We proposed a multichannel flexible pulse perception array based on polyimide/multiwalled carbon nanotube-polydimethylsiloxane nanocomposite/polyimide (PI/MPN/PI) sandwich-structure pressure sensor that can be applied for remote disease diagnosis. Furthermore, we established a mechanical model at the molecular level and guided the preparation of MPN. At the structural level, we achieved high sensitivity (35.02 kPa-1) and a broad response range (0-18 kPa) based on a pyramid-like bilayer microstructure with different upper and lower surfaces. A 27-channel (3 × 9) high-density sensor array was integrated at the device level, which can extract the spatial and temporal distribution information on a pulse. Furthermore, two intelligent algorithms were developed for extracting six-dimensional pulse information and automatic pulse recognition (the recognition rate reaches 97.8%). The results indicate that intelligent disease diagnosis systems have great potential applications in wearable healthcare devices.

Flexible hyperspectral surface plasmon resonance microscopy.

Optical techniques for visualization and quantification of chemical and biological analytes are always highly desirable. Here we show a hyperspectral surface plasmon resonance microscopy (HSPRM) system that uses a hyperspectral microscope to analyze the selected area of SPR image produced by a prism-based spectral SPR sensor. The HSPRM system enables monochromatic and polychromatic SPR imaging and single-pixel spectral SPR sensing, as well as two-dimensional quantification of thin films with the measured resonance-wavelength images. We performed pixel-by-pixel calibration of the incident angle to remove pixel-to-pixel differences in SPR sensitivity, and demonstrated the HSPRM's capabilities by using it to quantify monolayer graphene thickness distribution, inhomogeneous protein adsorption and single-cell adhesion. The HSPRM system has a wide spectral range from 400 nm to 1000 nm, an optional field of view from 0.884 mm2 to 0.003 mm2 and a high lateral resolution of 1.2 µm, demonstrating an innovative breakthrough in SPR sensor technology.

Fabrication of Glass Diaphragm Based Fiber-Optic Microphone for Sensitive Detection of Airborne and Waterborne Sounds.

A glass-diaphragm microphone was developed based on fiber-optic Fabry-Perot (FP) interferometry. The glass diaphragm was shaped into a wheel-like structure on a 150-µm-thick glass sheet by laser cutting, which consists of a glass disc connected to an outer glass ring by four identical glass beams. Such a structural diaphragm offers the microphone an open air chamber that reduces air damping and increases sensitivity and results in a cardioid direction pattern for the microphone response. The prepared microphone operates at 1550 nm wavelength, showing high stability in a range of temperature from 10 to 40 °C. The microphone has a resonance peak at 1152 Hz with a quality factor of 21, and its 3-dB cut-off frequency is 32 Hz. At normal incidence of 500 Hz sound, the pressure sensitivity of the microphone is 755 mV/Pa and the corresponding minimum detectable pressure is 251 µPa/Hz1/2. In addition to the above characteristics of the microphone in air, a preliminary investigation reveals that the microphone can also work stably under water for a long time due to the combination of the open-chamber and fiber-optic structures, and it has a large signal-to-noise ratio in response to waterborne sounds. The microphone prepared in this work is simple, inexpensive, and electromagnetically robust, showing great potential for low-frequency acoustic detection in air and under water.

Spatially Resolved Spectroscopic Characterization of Nanostructured Films by Hyperspectral Dark-Field Microscopy.

Nanostructured films have been widely used for preparing various advanced thin-film devices because of their unique electrical, optical, and plasmonic characteristics associated with the nano-size effect. In situ, nondestructive and high-resolution characterization of nanostructured films is essential for optimizing thin-film device performance. In this work, such thin-film characterization was achieved using a hyperspectral dark-field microscope (HSDFM) that was constructed in our laboratory by integrating a hyperspectral imager with a commercial microscope. The HSDFM allows for high-resolution (Δλ = 0.4 nm) spectral analysis of nanostructured samples in the visible-near-infrared region with a spatial resolution as high as 45 nm × 45 nm (corresponding to a single pixel). Four typical samples were investigated with the HSDFM, including the gold nanoplate array, the self-assembled gold nanoparticle (GNP) sub-monolayer, the sol-gel nanoporous titanium dioxide (TiO2) film, and the layer-stacked molybdenum disulfide (MoS2) sheet. According to the experimental results, the plasmon resonance scattering bands for nanoplate clusters are identical with those for individual gold nanoplates, indicating that the gap between adjacent nanoplates is too large to allow plasmonic coupling between them. A different case was observed with the self-assembled GNP sub-monolayer in which the aggregated clusters with the internal plasmonic interaction show a considerable red-shift of the plasmon resonance band relative to the isolated single GNP. In addition, the protein adsorption on the nanoporous TiO2 film was observed to be inhomogeneous on the microscale, and the stepped boundaries of the MoS2 sheet were clearly observed. A quasi-linear dependence of the single-pixel light intensity on the step height was obtained by combining the HSDFM with atomic force microscopy. The minimum thickness detectable by the present HSDFM is 6.5 nm, corresponding to the 10-layer MoS2 film. The work demonstrated the outstanding applicability of the HSDFM for nanostructured film characterization.

CB1-Antibody Modified Liposomes for Targeted Modulation of Epileptiform Activities Synchronously Detected by Microelectrode Arrays.

Temporal lobe epilepsy (TLE) is a focal, recurrent, and refractory neurological disorder. Therefore, precisely targeted treatments for TLE are greatly needed. We designed anti-CB1 liposomes that can bind to CB1 receptors in the hippocampus to deliver photocaged compounds (ruthenium bipyridine triphenylphosphine γ-aminobutyric acid, RuBi-GABA) in the TLE rats. A 16-channel silicon microelectrode array (MEA) was implanted for simultaneously monitoring electrophysiological signals of neurons. The results showed that anti-CB1 liposomes were larger in size and remained in the hippocampus longer than unmodified liposomes. Following the blue light stimulation, the neural firing rates and the local field potentials of hippocampal neurons were significantly reduced. It is indicated that RuBi-GABA was enriched near hippocampal neurons due to anti-CB1 liposome delivery and photolyzed by optical stimulation, resulting dissociation of GABA to exert inhibitory actions. Furthermore, K-means cluster analysis revealed that the firing rates of interneurons were decreased to a greater extent than those of pyramidal neurons, which may have been a result of the uneven diffusion of RuBi-GABA due to liposomes binding to CB1. In this study, we developed a novel, targeted method to regulate neural electrophysiology in the hippocampus of the TLE rat using antibody-modified nanoliposomes, implantable MEA, and photocaged compounds. This method effectively suppressed hippocampal activities during seizure ictus with high spatiotemporal resolution, which is a crucial exploration of targeted therapy for epilepsy.

Gold-silver alloy film based surface plasmon resonance sensor for biomarker detection.

In this study, we developed a gold­silver alloy film based surface plasmon resonance (AuAg-SPR) sensor with wavelength interrogation to detect cancer antigen 125 (CA125) using a sandwich immunoassay. We first theoretically simulated the sensitivity of conventional gold film based SPR (Au-SPR) sensor and AuAg-SPR sensor, and conducted a series of experiments to investigate the sensitive characteristics of AuAg-SPR sensor, including the angle and refractive index (RI) sensitivity. We then conducted CA125 detection experiments on these two types of sensors. The results demonstrated that the limit of detection (LOD) of CA125 on the AuAg-SPR sensor was 0.1 U/mL (0.8 ng/mL) based on its direct reaction with an immobilised antibody, which was two orders of magnitude lower than that of the Au-SPR sensor (10 U/mL). The total changes in the resonance wavelength (∆λR) of the former were 1.7-fold those of the latter. The volume fractions of the adsorbates (fad) and effective RIs (nadlayer) in each adlayer were then calculated and the effect of the antibody size on the detection results was analysed. The AuAg-SPR sensors had a higher sensitivity than the conventional Au-SPR sensors for detecting CA125 due to their electric field characteristics. Therefore, these will have better application prospects.

Nanoparticles Enhanced Self-driven Microfludic Biosensor.

C-reactive protein (CRP) plays an important role in inflammation detection and disease monitoring. The optical biosensor is a highly sensitive and easy detection tool. The microfluidic self-driving optical sensors were fabricated with transparent glass material and used for the enhanced surface plasmon resonance (SPR) optical detection of the model protein CRP using Au nanoparticles (AuNPs) and a sandwich immune reaction. The 3D design of the chip was devised to improve the optical coupling efficiency and enable integration with a microfluidic control and rapid detection. The array of pre-fixed antibody modified by Au nanoparticles was used to achieve rapid antigen capture and improve the optical sensitivity. The Au nanoparticle amplification approach was introduced for the SPR detection of a target protein. CRP was used as a model target protein as part of a sandwich assay. The use of Au NP measurements to detect the target signal is a threefold improvement compared to single SPR detection methods.

A Potassium Ion-Exchanged Glass Optical Waveguide Sensor Locally Coated with a Crystal Violet-SiO2 Gel Film for Real-Time Detection of Organophosphorus Pesticides Simulant.

An optical waveguide (OWG) sensor was developed for real-time detection of diethyl chlorophosphate (DCP) vapor, which is a typical simulant for organophosphorus pesticides and chemical weapon agents. Silica gel, crystal violet (CV), and potassium ion-exchange (PIE) OWG were used to fabricate the sensor's device. In the real-time detection of the DCP vapor, the volume fraction of DCP vapor was recorded to be as low as 1.68 × 10-9. Moreover, the detection mechanism of CV-SiO2 gel film coated the PIE OWG sensor for DCP, which was evaluated by absorption spectra. These results demonstrated that the change of output light intensity of the OWG sensor significantly increased with the augment of the DCP concentration. Repeatability as well as selectivity of the sensors were tested using 0.042 × 10-6 and 26.32 × 10-6 volume fraction of the DCP vapor. No clear interference with the DCP detection was observed in the presence of other common solvents (e.g., acetone, methanol, dichloromethane, dimethylsulfoxide, and tetrahydrofuran), benzene series (e.g., benzene, toluene, chlorobenzene, and aniline), phosphorus-containing reagents (e.g., dimethyl methylphosphonate and trimethyl phosphate), acid, and basic gas (e.g., acetic acid and 25% ammonium hydroxide), which demonstrates that the OWG sensor could provide real-time, fast, and accurate measurement results for the detection of DCP.

AuAg alloy film-based colorful SPR imaging sensor for highly sensitive immunodetection of benzo[a]pyrene in water.

A colorful surface plasmon resonance imaging (SPRi) sensor with the hue-based enhanced sensitivity has been developed by using sputtered AuAg alloy thin film as the sensing layer. The condition for optimizing the hue-based sensitivity of the SPRi sensor was achieved, that is, the initial resonance wavelength is in the range from 595 to 610 nm. Under this condition, the hue-based refractive index sensitivity of the SPRi sensor was measured as high as Δhue/Δnc=29879/RIU. This sensitivity is 8 times higher than that obtained with a gold-layer SPRi sensor (Δhue/Δnc=3658/RIU) and 7.7 times as high in magnitude as the spectral sensitivity of the same sensor (ΔλR/Δnc=3897.6 nm/RIU). After functionalization of the AuAg alloy film with the monoclonal antibody, the sensor was used for quantitative immunodetection of highly carcinogenic benzo[a]pyrene (BaP) in water. According to the experimental results, the average hue of the SPR color image (300 pixels×300 pixels) experiences an initial rapid increase and then stabilizes 15 min after exposure of the functionalized AuAg alloy film to an aqueous BaP solution sample. The variation of average hue obtained at the equilibrium of surface immunoreaction is a linear function of BaP concentration with the slope being Δhue/Δc=132.2/(µg·L-1). A cooled CCD camera is able to distinguish a change of Δhue=1, offering the colorful SPRi sensor the BaP detection limit of 0.01 µg·L-1. The comparative measurements of the sensor's responses indicate that the hue variation obtained with 0.1 µg·L-1 of BaP is equal to that obtained either with 5 µg·L-1 of benzanthracene or with 5 µg·L-1 of benzofluoranthene, revealing the sensor's excellent specificity to BaP. The work demonstrated that the AuAg alloy film-based colorful SPRi sensor can be used not only for visualized analysis of molecular interaction at the surface but also for quantitative trace detection of small-molecule analytes.

A Sensitive Piezoresistive Tactile Sensor Combining Two Microstructures.

A tactile sensor is an indispensable component for electronic skin, mimicking the sensing function of organism skin. Various sensing materials and microstructures have been adopted in the fabrication of tactile sensors. Herein, we propose a highly sensitive flexible tactile sensor composed of nanocomposites with pyramid and irregularly rough microstructures and implement a comparison of piezoresistive properties of nanocomposites with varying weight proportions of multi-wall nanotubes and carbon black particles. In addition to the simple and low-cost fabrication method, the tactile sensor can reach high sensitivity of 3.2 kPa-1 in the range of <1 kPa and fast dynamic response of 217 ms (loading) and 81 ms (recovery) at 40 kPa pressure. Moreover, body movement monitoring applications have been carried out utilizing the flexible tactile sensor. A sound monitoring application further indicates the potential for applications in electronic skin, human-computer interaction, and physiological detection.