RESUMEN
The radiation effect of materials is very important and directly related to the safety and reliability of nuclear reactors. Polymer materials, one of the indispensable materials in nuclear power equipment, must withstand the ordeal of high-energy ionizing rays. In this work, through screening different γ-ray dose irradiation conditions, we systematically and comprehensively study the changes in the structure and properties of nitrile butadiene rubber (NBR) before and after γ-ray static irradiation at a high dose rate, and master the rule and mechanism of the γ-ray static irradiation effect of these polymer materials. The mapping relationship between the macroscopic properties, microstructure, and irradiation dose of NBR is accurately characterized. With an increase in total irradiation dose, the C=C double bond reaction occurs, and the C≡N bond, C=C, and C=O participate in the hyper crosslinking reaction. The glass transition temperature (Tg) increases with the cumulative irradiation amount. With the increased total irradiation amount, the degree of rubber cross-linking increases, causing an increased crystallinity and decomposition temperature. A growing amount of gamma irradiation causes the mechanical properties of the rubber to degrade simultaneously, increasing the shore hardness while decreasing the tensile strength and ultimate elongation at break. When the cumulative amount reaches 1 MGy, the ultimate elongation at break decreases significantly. A cumulative dose of radiation resistance of 4 MGy can be achieved by the samples. This work can provide theoretical and experimental support for the long-term stability of nitrile butadiene rubber and its derivatives in nuclear radiation fields and space radiation conditions.
RESUMEN
On-orbit cophasing is essential for high-resolution imaging of space telescopes with a segmented primary mirror. A model-based fine phasing method for a segmented mirror is proposed and demonstrated in this Letter. The tip-tilt error is related to the second moment of spot intensity, and the piston error is related to the Strehl ratio. Chebyshev segmented piston-tip-tilt (CSPTT) modes are used to express cophasing errors to suppress the effect of imaging noises. The CSPTT modal coefficients are estimated by the "2N + 1" algorithm that introduces bidirectional biases for each mode's estimation. The proposed method is proved robust to image noises and figure errors.
RESUMEN
The deformable mirror (DM) in conventional model-based wavefront sensorless adaptive optics (WFSless AO) must be calibrated in advance by an additional WFS in order to precisely generate predetermined bias modes with known amplitudes. Although the WFS is unnecessary during correction, it will increase system complexity and may be unavailable in real applications. In this paper, the model-based WFSless AO algorithms, either for point-like or extended objects, are generalized to a unified form and the calibration problem comes down to the measurement of a Gram matrix. We proposed a novel self-calibration procedure to obtain the Gram matrix without using a WFS. The calibrated Gram matrix can be used directly for simultaneous correction if using the influence functions of DM as the bias modes, requiring N+1 images to correct N modes. Alternatively, orthogonal or gradient-orthogonal mirror modes obtained from the eigenvectors of the Gram matrix can be used as the modal basis to implement independent sequential correction that requires 2N images to correct N modes. Simulations and experiments have been done to verify the feasibility of proposed self-calibration and correction methods for both point-like and extended objects in a WFSless AO system.
RESUMEN
A major concern for wavefront sensorless adaptive optics (WFSless AO) is how to improve the algorithm's efficiency which is critical for dynamic aberration correction. For extended objects and dynamic aberration, a typical model-based WFSless AO algorithm is called "3N" which uses three image measurements to estimate each aberration mode and then corrects it immediately. The three images include an initial aberrated image and two biased images with deliberately introduced predetermined positive or negative modal aberrations. In this paper, an improved algorithm called "2N" that requires only one biased image is proposed. The reduction of one biased image is achieved by the estimation of a parameter that is considered unknown in the 3N algorithm. It is demonstrated that the 2N algorithm can achieve convergence with less image measurements and have better performance in dynamic correction.
RESUMEN
The precise alignment of the space telescope with an active secondary mirror (ASM) is essential to high-quality imaging. The traditional alignment methods either require a dedicated wavefront sensor or a lot of iterations to optimize a metric function, which is not suitable for on-orbit instant alignment. A model-based wavefront sensorless adaptive optics method is proposed for the alignment of the ASM of a wide field-of-view space telescope. In our method, the aberration is estimated by introducing a series of modal biases successively into the system using the ASM. Unlike the traditional wavefront sensing methods that intend to measure all aberration modes, only five aberration modes that can be compensated by the ASM are estimated. Two alignment schemes either using single-field or multi-field images are proposed to calculate the control signals of the ASM, depending on if the aberration is mainly caused by the ASM. Simulations are made to evaluate the performance of our method under different scenarios. The influence of image sampling frequency, image size, and image noise on alignment are also investigated.
RESUMEN
The original model-based wavefront sensorless adaptive optics (WFSless AO) for extended objects uses the low spatial frequency content of images as the metric function and employs 2N + 1 images to correct N Lukosz aberration modes. We propose an improved method that uses the same metric but requires only N + 2 images to correct N aberration modes. The N + 2 method can achieve comparable corrective accuracy but requiring much smaller number of images compared with the 2N + 1 method. The N + 2 method is not only more efficient, but also provides the flexibility of choosing arbitrary basis modes by involving the non-orthogonality between modes in a linear least-squares optimization process. It is demonstrated that the deformable mirror's influence functions modes (IFM), orthogonal mirror modes (OMM) and fitted Zernike modes (FZM) all can be used as modal basis for the N + 2 method to generate biased images. It is also proved that the N + 2 method is robust to image sampling rate and image noise, showing good prospects of applications in various imaging systems.