RESUMEN
The fiber surface plasmon resonance (SPR) sensor used for the detection of active ingredients in traditional Chinese medicine has the problems of low sensitivity and difficult specific recognition. This paper proposed a wave type fiber SPR sensor, which reduced the mode of transmitted light through a periodic wave structure and caused concentrated and total reflection of the transmitted beam at the interface between the bent peak cladding and the air. A 50â nm gold film was coated on the surface of the cladding in the wave structure area to form the SPR sensing area. By controlling the width and height of the wave structure to control the total reflection angle of the transmitted light, i.e., the SPR incidence angle, the sensitivity of the fiber SPR sensor was effectively improved to 4972â nm/RIU. Furthermore, HSP90AA protein was modified on the gold film of the sensor to achieve specific detection of hyperoside. The longest single detection time was only 3 minutes, and the detection sensitivity was 0.53â nm/(µg/ml), with a detection limit as low as 0.68µg/ml, which is comparable to liquid chromatography. The proposed wave type fiber SPR sensor is fast in production and has high structural mechanical strength, providing a new approach for the rapid, highly sensitive, and specific detection of active ingredients in traditional Chinese medicine.
RESUMEN
To achieve a fiber strain sensor with a large detection range and high sensitivity, this paper proposes a wave structured fiber SPR strain sensor. When subjected to axial strain, the wave structured fiber is stretched axially, increasing the stretchability of the sensor and achieving a large detection range strain sensing. Meanwhile, axial strain reduces the longitudinal amplitude of the fiber wave structure, effectively changing the total reflection angle of the transmitted beam at the peak and valley (SPR incidence angle) to achieve high sensitivity SPR strain sensing. The experiment indicates that the strain detection range of the sensor can reach 0-1800µÎµ, with a maximum strain sensitivity of 36.25pm/µÎµ. The wave structured fiber SPR strain sensor designed in this article provides a new approach to improve the range and sensitivity of strain detection.
RESUMEN
The current temperature-compensated fiber-optic surface plasmon resonance (SPR) biosensors are mainly open-ended outside the sensing structure, and there is a lack of temperature compensation schemes in fiber-optic microfluidic chips. In this paper, we proposed a temperature-compensated optical fiber SPR microfluidic sensor based on micro-nano 3D printing. Through the optical fiber micro-machining technology, the two sensing areas were designed on both sides of the same sensing fiber. The wavelength division multiplexing technology was used to collect the sensing light signals of the two sensing areas at the same time. The specific measurement of berberine and the detection of ambient temperature in the optical fiber SPR biological microfluidic channel were realized, and the temperature compensation matrix relationship was constructed, and then the temperature compensation was realized when measuring berberine biomolecules. Experiments have shown that the temperature sensitivity of the optical fiber SPR microfluidic sensor was 2.18â nm/°C, the sensitivity of the detection of berberine was 0.2646â nm/(µg/ml), the detection limit (LOD) was 0.38 µg/ml, and in a mixed solution showed an excellent specific detection impact.
RESUMEN
At present, fiber strain sensors are mainly of the grating type and interference type, while there is relatively little research on fiber surface plasmon resonance (SPR) strain sensors. In this Letter, we propose a highly sensitive fiber SPR strain sensor based on an n-type structure. The strain changes the shape of the fiber n-type structure, causing the transmission mode of light in the fiber to change, thereby changing the SPR incidence angle and causing the SPR resonance valley wavelength to shift, achieving highly sensitive SPR strain sensing. The test results indicate that the strain sensing sensitivity of the proposed sensor reaches 21.33â pm/µÎµ, and two n-type structures are connected in series to obtain a double n-type structure, further enhancing the strain sensing sensitivity to 33.44â pm/µÎµ. This fiber strain sensor has advantages of high sensitivity, low temperature cross talk, strong structural stability, and low production cost, and is expected to become a new solution for wearable intelligent monitoring equipment and strain sensors in the aerospace field.
RESUMEN
At present, fiber curvature sensors based on surface plasmon resonance (SPR) are mostly of the multimode fiber core type or cladding type. These types have many SPR modes, resulting that the sensitivity cannot be adjusted and is difficult to improve. In this Letter, a highly sensitive SPR curvature sensor based on graded-index fiber is proposed. The light-injecting fiber is eccentrically connected with the graded-index fiber to inject single-mode light. Due to the self-focusing effect, the light beam propagates in the graded-index multimode fiber with a cosine trajectory, and the cosine beam contacts the flat grooved sensing region fabricated on the graded-index fiber to generate SPR. Due to the single transmission mode of the proposed fiber SPR sensor, the curvature sensing sensitivity is greatly improved. By changing the light injection position of the graded-index multimode fiber, the sensitivity can be adjusted. The proposed curvature sensing probe has a high sensitivity and can identify the bending direction. When bending in the X direction, the sensitivity reaches 5.62â nm/m-1, and when bending in the - X direction, the sensitivity reaches 4.75â nm/m-1, which provides a new scheme for highly sensitive and directionally identifiable curvature measurement.