Piezoelectric Peptide Nanotube Substrate Sensors Activated through Sound Wave Energy.

The use of sustainable and safe materials is increasingly in demand for the creation of photonic-based technology. Piezoelectric peptide nanotubes make up a class of safe and sustainable materials. We show that these materials can generate piezoelectric charge through the deformation of oriented molecular dipoles when the tube length is flexed through the application of sound energy. Through the combination of peptide nanotubes with plasmon active nanomaterials, harvesting of low-frequency acoustic sound waves was achieved. This effect was applied to boost surface-enhanced Raman scattering signal detection of analytes, including glucose. This work demonstrates the potential of utilizing sound to boost sensing by using piezoelectric materials.

Modification of Living Diatom, Thalassiosira weissflogii, with a Calcium Precursor through a Calcium Uptake Mechanism: A Next Generation Biomaterial for Advanced Delivery Systems.

The diatom's frustule, characterized by its rugged and porous exterior, exhibits a remarkable biomimetic morphology attributable to its highly ordered pores, extensive surface area, and unique architecture. Despite these advantages, the toxicity and nonbiodegradable nature of silica-based organisms pose a significant challenge when attempting to utilize these organisms as nanotopographically functionalized microparticles in the realm of biomedicine. In this study, we addressed this limitation by modulating the chemical composition of diatom microparticles by modulating the active silica metabolic uptake mechanism while maintaining their intricate three-dimensional architecture through calcium incorporation into living diatoms. Here, the diatom Thalassiosira weissflogii was chemically modified to replace its silica composition with a biodegradable calcium template, while simultaneously preserving the unique three-dimensional (3D) frustule structure with hierarchical patterns of pores and nanoscale architectural features, which was evident by the deposition of calcium as calcium carbonate. Calcium hydroxide is incorporated into the exoskeleton through the active mechanism of calcium uptake via a carbon-concentrating mechanism, without altering the microstructure. Our findings suggest that calcium-modified diatoms hold potential as a nature-inspired delivery system for immunotherapy through antibody-specific binding.

A nano-imprinted graphene oxide-cellulose composite as a SERS active substrate.

Cellulose is a sustainable material capable of forming optically active nanoarrays on its surface. We created a composite of cellulose acetate (CA) and graphene oxide (GO), by mixing GO (0.1 mg mL-1) into CA. This was then imprinted with nanoscale surface features that form Bragg-like modes in resonance with the excitation laser when a thin layer of silver is vapor deposited onto the surface of the substrate. The addition of GO leads to improved surface-enhanced Raman scattering (SERS) signal strengths, obtaining an average SERS signal increase of 1.4-fold following the inclusion of GO. The combination of photonic and electromagnetic effects with charge transfer-based processes that support the SERS chemical mechanism and the possible presence of electromagnetic hot spots from the roughened surface results in an enhanced SERS signal strength when GO is added. This work shows the potential for nanoimprinted graphene oxide/cellulose acetate composites as flexible sensor platforms to detect target molecules.

Evidence of the Monopolar-Dipolar Crossover Regime: A Multiscale Study of Ferroelastic Domains by In Situ Microscopy Techniques.

The elastic interaction between kinks (and antikinks) within domain walls plays a pivotal role in shaping the domain structure, and their dynamics. In bulk materials, kinks interact as elastic monopoles, dependent on the distance between walls (d-1) and typically characterized by a rigid and straight domain configuration. In this work the evolution of the domain structure is investigated, as the sample size decreases, by the means of in situ heating microscopy techniques on free-standing samples. As the sample size decreases, a significant transformation is observed: domain walls exhibit pronounced curvature, accompanied by an increase in both domain wall and junction density. This transformation is attributed to the pronounced influence of kinks, inducing sample warping, where "dipole-dipole" interactions are dominant (d-2). Moreover, a critical thickness range that delineates a crossover between the monopolar and dipolar regimens is experimentally identified and corroborated by atomic simulations. These findings are relevant for in situ TEM studies and for the development of novel devices based on free-standing ferroic thin films and nanomaterials.

Reproducible Synthesis of Biocompatible Albumin Nanoparticles Designed for Intra-articular Administration of Celecoxib to Treat Osteoarthritis.

Osteoarthritis (OA) is the most common form of arthritis, with intra-articular (IA) delivery of therapeutics being the current best option to treat pain and inflammation. However, IA delivery is challenging due to the rapid clearance of therapeutics from the joint and the need for repeated injections. Thus, there is a need for long-acting delivery systems that increase the drug retention time in joints with the capacity to penetrate OA cartilage. As pharmaceutical utility also demands that this is achieved using biocompatible materials that provide colloidal stability, our aim was to develop a nanoparticle (NP) delivery system loaded with the COX-2 inhibitor celecoxib that can meet these criteria. We devised a reproducible and economical method to synthesize the colloidally stable albumin NPs loaded with celecoxib without the use of any of the following conditions: high temperatures at which albumin denaturation occurs, polymer coatings, oils, Class 1/2 solvents, and chemical protein cross-linkers. The spherical NP suspensions were biocompatible, monodisperse with average diameters of 72 nm (ideal for OA cartilage penetration), and they were stable over 6 months at 4 °C. Moreover, the NPs loaded celecoxib at higher levels than those required for the therapeutic response in arthritic joints. For these reasons, they are the first of their kind. Labeled NPs were internalized by primary human articular chondrocytes cultured from the knee joints of OA patients. The NPs reduced the concentration of inflammatory mediator prostaglandin E2 released by the primaries, an indication of retained bioactivity following NP synthesis. Similar results were observed in lipopolysaccharide-stimulated human THP-1 monocytes. The IA administration of these NPs is expected to avoid side-effects associated with oral administration of celecoxib and to maintain a high local concentration in the knee joint over a sustained period. They are now ready for evaluation by IA administration in animal models of OA.

Structure-dynamics correlations in composite PF127-PEG-based hydrogels; cohesive/hydrophobic interactions determine phase and rheology and identify the role of micelle concentration in controlling 3D extrusion printability.

A library of composite polymer networks (CPNs) were formed by combining Pluronic F127, as the primary gelator, with a range of di-acrylate functionalised PEG polymers, which tune the rheological properties and provide UV crosslinkability. A coarse-grained sol-gel room temperature phase diagram was constructed for the CPN library, which identifies PEG-dependent disruption of micelles as leading to liquefication. Small angle X-ray scattering and rheological measurements provide detailed insight into; (i) micelle-micelle ordering; (ii) micelle-micelle disruption, and; (iii) acrylate-micelle disruption; with contributions that depend on composition, including weak PEG chain length and end group effects. The influence of composition on 3D extrusion printability through modulation of the cohesive/hydrophobic interactions was assessed. It was found that only micelle content provides consistent changes in printing fidelity, controlled largely by printing conditions (pressure and feed rate). Finally, the hydrogels were shown to be UV photo-crosslinkable, which further improves fidelity and structural integrity, and usefully reduces the mesh size. Our results provide a guide for design of 3D-printable CPN inks for future biomedical applications.

Magnetic Chitosan Bionanocomposite Films as a Versatile Platform for Biomedical Hyperthermia.

Responsive magnetic nanomaterials offer significant advantages for innovative therapies, for instance, in cancer treatments that exploit on-demand delivery on alternating magnetic field (AMF) stimulus. In this work, biocompatible magnetic bionanocomposite films are fabricated from chitosan by film casting with incorporation of magnetite nanoparticles (MNPs) produced by facile one pot synthesis. The influence of synthesis conditions and MNP concentration on the films' heating efficiency and heat dissipation are evaluated through spatio-temporal mapping of the surface temperature changes by video-thermography. The cast films have a thickness below 100 µm, and upon exposure to AMF (663 kHz, 12.8 kA m-1 ), induce exceptionally strong heating, reaching a maximum temperature increase of 82 °C within 270 s irradiation. Further, it is demonstrated that the films can serve as substrates that supply heat for multiple hyperthermia scenarios, including: i) non-contact automated heating of cell culture medium, ii) heating of gelatine-based hydrogels of different shapes, and iii) killing of cancerous melanoma cells. The films are versatile components for non-contact stimulus with translational potential in multiple biomedical applications.

Role of pH and Crosslinking Ions on Cell Viability and Metabolic Activity in Alginate-Gelatin 3D Prints.

Alginate-gelatin hydrogels are extensively used in bioengineering. However, despite different formulations being used to grow different cell types in vitro, their pH and its effect, together with the crosslinking ions of these formulations, are still infrequently assessed. In this work, we study how these elements can affect hydrogel stability and printability and influence cell viability and metabolism on the resulting 3D prints. Our results show that both the buffer pH and crosslinking ion (Ca2+ or Ba2+) influence the swelling and degradation rates of prints. Moreover, buffer pH influenced the printability of hydrogel in the air but did not when printed directly in a fluid-phase CaCl2 or BaCl2 crosslinking bath. In addition, both U2OS and NIH/3T3 cells showed greater cell metabolic activity on one-layer prints crosslinked with Ca2+. In addition, Ba2+ increased the cell death of NIH/3T3 cells while having no effect on U2OS cell viability. The pH of the buffer also had an important impact on the cell behavior. U2OS cells showed a 2.25-fold cell metabolism increase on one-layer prints prepared at pH 8.0 in comparison to those prepared at pH 5.5, whereas NIH/3T3 cells showed greater metabolism on one-layer prints with pH 7.0. Finally, we observed a difference in the cell arrangement of U2OS cells growing on prints prepared from hydrogels with an acidic buffer in comparison to cells growing on those prepared using a neutral or basic buffer. These results show that both pH and the crosslinking ion influence hydrogel strength and cell behavior.

Electromechanical Coupling in Collagen Measured under Increasing Relative Humidity.

The functional role of collagen piezoelectricity has been under debate since the discovery of piezoelectricity in bone in 1957. The possibility that piezoelectricity plays a role in bone remodeling has generated interest in the investigation of this effect in relevant physiological conditions; however, there are conflicting reports as to whether collagen is piezoelectric in a humid environment. In macroscale measurements, the piezoelectricity in hydrated tendon has been shown to be insignificant compared to dehydrated tendon, whereas, at the nanoscale, the piezoelectric effect has been observed in both dry and wet bone using piezoresponse force microscopy (PFM). In this work, the electromechanical properties of type I collagen from a rat tail tendon have been investigated at the nanoscale as a function of humidity using lateral PFM (LPFM) for the first time. The relative humidity (RH) was varied from 10% to 70%, allowing the piezoelectric behavior to be studied dry, humid, as well as in the hydrated range for collagen in physiological bone (12% moisture content, corresponding to 40-50% RH). The results show that collagen piezoresponse can be measured across the humidity range studied, suggesting that piezoelectricity remains a property of collagen at a biologically relevant humidity.

Cycle-dependent morphology and surface potential of germanium nanowire anode electrodes.

Germanium nanowire (GeNW) electrodes have shown great promise as high-power, fast-charging alternatives to silicon-based electrodes, owing to their vastly improved Li ion diffusion, electron mobility and ionic conductivity. Formation of the solid electrolyte interphase (SEI) on the anode surface is critical to electrode performance and stability but is not completely understood for NW anodes. Here, a systematic study characterizing pristine and cycled GeNWs in charged and discharged states with SEI layer present and removed is performed using Kelvin probe force microscopy in air. Correlating changes in the morphology of the GeNW anodes with contact potential difference mapping at different cycles provides insight into SEI layer formation and growth, and the effect of the SEI on battery performance.

Controlled degradation of polycaprolactone-based micropillar arrays.

Herein we demonstrate the fabrication of arrays of micropillars, achieved through the combination of direct laser writing and nanoimprint lithography. By combining two diacrylate monomers, polycaprolactone dimethacrylate (PCLDMA) and 1,6-hexanediol diacrylate (HDDA), two copolymer formulations that, owing to the varying ratios of the hydrolysable ester functionalities present in the polycaprolactone moiety, can be degraded in the presence of base in a controllable manner. As such, the degradation of the micropillars can be tuned over several days as a function of PCLDMA concentration within the copolymer formulations, and the topography greatly varied over a short space of time, as visualised using scanning electron microscopy and atomic force microscopy. Crosslinked neat HDDA was used as a control material, demonstrating that the presence of the PCL was responsible for the ability of the microstructures to degrade in the controlled manner. In addition, the mass loss of the crosslinked materials was minimal, demonstrating the degradation of microstructured surfaces without loss of bulk properties was possible. Moreover, the compatibility of these crosslinked materials with mammalian cells was explored. The influence of both indirect and direct contact of the materials with A549 cells was assessed by profiling indices reflective of cytotoxicity such as morphology, adhesion, metabolic activity, oxidative balance, and release of injury markers. No significant changes in the aforementioned profile were observed in the cells cultured under these conditions for up to 72 h, with the cell-material interaction suggesting these materials may have potential in microfabrication contexts towards biomedical application purposes.

Comparing the performance of single and multifrequency Kelvin probe force microscopy techniques in air and water.

In this paper, we derive and present quantitative expressions governing the performance of single and multifrequency Kelvin probe force microscopy (KPFM) techniques in both air and water. Metrics such as minimum detectable contact potential difference, minimum required AC bias, and signal-to-noise ratio are compared and contrasted both off resonance and utilizing the first two eigenmodes of the cantilever. These comparisons allow the reader to quickly and quantitatively identify the parameters for the best performance for a given KPFM-based experiment in a given environment. Furthermore, we apply these performance metrics in the identification of KPFM-based modes that are most suitable for operation in liquid environments where bias application can lead to unwanted electrochemical reactions. We conclude that open-loop multifrequency KPFM modes operated with the first harmonic of the electrostatic response on the first eigenmode offer the best performance in liquid environments whilst needing the smallest AC bias for operation.

Controlling Amyloid Fibril Properties Via Ionic Liquids: The Representative Case of Ethylammonium Nitrate and Tetramethylguanidinium Acetate on the Amyloidogenesis of Lysozyme.

Protein aggregation into amyloid fibrils has been observed in several pathological conditions and exploited in nanotechnology. It is also key in several biochemical processes. In this work, we show that ionic liquids (ILs), a vast class of organic electrolytes, can finely tune amyloid properties, opening a new landscape in basic science and applications. The representative case of ethylammonium nitrate (EAN) and tetramethyl-guanidinium acetate (TMGA) ILs on lysozyme is considered. First, atomic force microscopy has shown that the addition of EAN and TMGA leads to thicker and thinner amyloid fibrils of greater and lower electric potential, respectively, with diameters finely tunable by IL concentration. Optical tweezers and neutron scattering have shed light on their mechanism of action. TMGA interacts with the protein hydration layer only, making the relaxation dynamics of these water molecules faster. EAN interacts directly with the protein instead, making it mechanically unstable and slowing down its relaxation dynamics.

Microfabrication of peptide self-assemblies: inspired by nature towards applications.

Peptide self-assemblies show intriguing and tunable physicochemical properties, and thus have been attracting increasing interest over the last two decades. However, the micro/nano-scale dimensions of the self-assemblies severely restrict their extensive applications. Inspired by nature, to genuinely realize the practical utilization of the bio-organic super-architectures, it is beneficial to further organize the peptide self-assemblies to integrate the properties of the individual supermolecules and fabricate higher-level organizations for smart functional devices. Therefore, cumulative studies have been reported on peptide microfabrication giving rise to diverse properties. This review summarizes the recent development of the microfabrication of peptide self-assemblies, discussing each methodology along with the diverse properties and practical applications of the engineered peptide large-scale, highly-ordered organizations. Finally, the current limitations of the state-of-the-art microfabrication strategies are critically assessed and alternative solutions are suggested.

A Biomimetic High Throughput Model of Cancer Cell Spheroid Dissemination onto Aligned Fibrillar Collagen.

Cell dissemination during tumor development is a characteristic of cancer metastasis. Dissemination from three-dimensional spheroid models on extracellular matrices designed to mimic tissue-specific physiological microenvironments may allow us to better elucidate the mechanism behind cancer metastasis and the response to therapeutic agents. The orientation of fibrillar collagen plays a key role in cellular processes and mediates metastasis through contact-guidance. Understanding how cells migrate on aligned collagen fibrils requires in vitro assays with reproducible and standardized orientation of collagen fibrils on the macro-to-nanoscale. Herein, we implement a spheroid-based migration assay, integrated with a fibrillar type I collagen matrix, in a manner compatible with high throughput image acquisition and quantitative analysis. The migration of highly proliferating U2OS osteosarcoma cell spheroids onto an aligned fibrillar type I collagen matrix was quantified. Cell dissemination from the spheroid was polarized with increased invasion in the direction of fibril alignment. The resulting area of cell dissemination had an aspect ratio of 1.2 ± 0.1 and an angle of maximum invasion distance of 5° ± 44° relative to the direction of collagen fibril alignment. The assay described here can be applied to a fully automated imaging and analysis pipeline for the assessment of tumor cell migration with high throughput screening.

Structure Fabrication on Silicon at Atomic and Close-To-Atomic Scale Using Atomic Force Microscopy: Implications for Nanopatterning and Nanodevice Fabrication.

In this paper, the atomic-scale structure fabrication on Si (100) substrate using atomic force microscopy (AFM) with the aid of electrochemical and mechanical processes in a humid environment and under ambient conditions is studied. The local oxidation patterns are formed using platinum-coated tips with the aid of bias applied to the tip-substrate junction, and direct removal has been achieved using single crystal diamond tips, enabling the structure fabrication at the atomic and close-to-atomic scale. The depth and height of the etched trenches reached about 1 nm, which provides an approach for the fabrication of atomic-scale electrodes for molecular device development. Furthermore, material removal close to about three silicon atoms (~3.2 Å) has been achieved. This is important in molecular device fabrication. A detailed comparison among the nanopatterns and the material removal over bare and hydrofluoric acid (HF) treated silicon substrates is provided. This comparison is useful for the application of fabricating atomic-scale electrodes needed for the molecular electronic components. A deep understanding of atomic-scale material removal can be pushed to fabricate a single atomic protrusion by removing the neighbouring atoms so that the molecule can be attached to a single atom, thereby the AFM tip and Si substrate could act as the electrodes and the molecule between them as the channel, providing basic transistor actions in a molecular transistor design. In this paper, platinum-coated and single-crystal diamond tips are used to explain the oxide formations and direct material removal, respectively.

Toward Single-Atomic-Layer Lithography on Highly Oriented Pyrolytic Graphite Surfaces Using AFM-Based Electrochemical Etching.

Atomic force microscopy (AFM)-based electrochemical etching of a highly oriented pyrolytic graphite (HOPG) surface is studied toward the single-atomic-layer lithography of intricate patterns. Electrochemical etching is performed in the water meniscus formed between the AFM tip apex and HOPG surface due to a capillary effect under controlled high relative humidity (~ 75%) at otherwise ambient conditions. The conditions to etch nano-holes, nano-lines, and other intricate patterns are investigated. The electrochemical reactions of HOPG etching should not generate debris due to the conversion of graphite to gaseous CO and CO2 based on etching reactions. However, debris is observed on the etched HOPG surface, and incomplete gasification of carbon occurs during the etching process, resulting in the generation of solid intermediates. Moreover, the applied potential is of critical importance for precise etching, and the precision is also significantly influenced by the AFM tip wear. This study shows that the AFM-based electrochemical etching has the potential to remove the material in a single-atomic-layer precision. This result is likely because the etching process is based on anodic dissolution, resulting in the material removal atom by atom.

Structural Transition-Induced Raman Enhancement in Bioinspired Diphenylalanine Peptide Nanotubes.

Semiconducting materials are increasingly proposed as alternatives to noble metal nanomaterials to enhance Raman scattering. We demonstrate that bioinspired semiconducting diphenylalanine peptide nanotubes annealed through a reported structural transition can support Raman detection of 10-7 M concentrations for a range of molecules including mononucleotides. The enhancement is attributed to the introduction of electronic states below the conduction band that facilitate charge transfer to the analyte molecule. These results show that organic semiconductor-based materials can serve as platforms for enhanced Raman scattering for chemical sensing. As the sensor is metal-free, the enhancement is achieved without the introduction of electromagnetic surface-enhanced Raman spectroscopy.

Mechanical writing of electrical polarization in poly (L-lactic) acid.

Stimuli responsive materials are found in a broad range of applications, from energy harvesters to biomolecular sensors. Here, we report the production of poly (L-lactic acid) (PLLA) thin films that exhibit a mechanical stress responsive behaviour. By simply applying a mechanical stress through an AFM tip, a local electrical polarization was generated and measured by Kelvin Probe Force Microscopy. We showed that the magnitude of the stress generated electrical polarization can be manipulated by varying the thickness or crystallization state of the PLLA thin films. Besides exhibiting a mechanical stress-response behaviour with potential for energy harvesting and sensor applications, we show by AFM that these platforms react to mechanical forces with physiological relevance: interaction forces as low as a cell sheet migrating over a substrate or larger ones as the fluid induced stresses in bone tissue. In living tissues, as most mechanical stimuli are transduced as strain gradients for the anatomical structures, these mechanically responsive substrates can be used as ex vivo platforms to study the protein and cells response over a large range of electrical stimuli amplitude. As a proof of concept, selective adsorption of a human fibronectin was demonstrated by local patterning of the stimuli responsive PLLA films. STATEMENT OF SIGNIFICANCE: Bioelectricity is inherent to the formation and repair of living tissues and electrical stimulation has been recognized for promoting regeneration. Given the proven beneficial effects of electric fields and the absence of a suitable method of stimulation, there is a clinical need for smart substrates, which can generate a polarization (charges) to promote tissue regeneration without the need of external devices. In this work, we report the fabrication of poly(L-lactic) acid platforms that exhibit a mechanical stress responsive behaviour when subjected to physiologically relevant forces. This behaviour can be tailored by varying the thickness or crystallization state of the PLLA films. We further demonstrate the biofunctionality of such platforms by exploiting the mechanically-induced charge for adhesion protein adsorption.

Graphene oxide modulates inter-particle interactions in 3D printable soft nanocomposite hydrogels restoring magnetic hyperthermia responses.

Hydrogels loaded with magnetic iron oxide nanoparticles that can be patterned and which controllably induce hyperthermic responses on AC-field stimulation are of interest as functional components of next-generation biomaterials. Formation of nanocomposite hydrogels is known to eliminate any Brownian contribution to hyperthermic response (reducing stimulated heating) while the Néel contribution can also be suppressed by inter-particle dipolar interactions arising from aggregation induced before or during gelation. We describe the ability of graphene oxide (GO) flakes to restore the hyperthermic efficiency of soft printable hydrogels formed using Pluronics F127 and PEGylated magnetic nanoflowers. Here, by varying the amount of GO in mixed nanocomposite suspensions and gels, we demonstrate GO-content dependent recovery of hyperthemic response in gels. This is due to progressively reduced inter-nanoflower interactions mediated by GO, which largely restore the dispersed-state Néel contribution to heating. We suggest that preferential association of GO with the hydrophobic F127 blocks increases the preponderance of cohesive interactions between the hydrophilic blocks and the PEGylated nanoflowers, promoting dispersion of the latter. Finally we demonstrate extrusion-based 3D printing with excellent print fidelity of the magnetically-responsive nanocomposites, for which the inclusion of GO provides significant improvement in the spatially-localized open-coil heating response, rendering the prints viable components for future cell stimulation and delivery applications.