Integrating Cellulose Microfibrils and Ellagitannins from Rambutan Peel with Gelatin for Production of Synergistic Biobased Hydrogels.

The pursuit of renewable and eco-friendly raw materials for biobased materials is a growing field. This study utilized ellagitannin and cellulose microfibrils derived from rambutan peel waste alongside gelatin to develop eco-conscious hydrogels. The cellulose/gelatin hydrogels were formulated in two weight ratios (0.5:1 to 1:1), and the influence of gelatin on the chemical composition and rheology was studied. Composite hydrogels, functionalized with an ellagitannin-rich extract, exhibited a remarkable enhancement of up to 14-fold in compressive strength. The hydrogels also demonstrated antimicrobial properties, reducing the Staphylococcus aureus colony count within 24 h. The hydrogel, derived from rambutan peel waste, is biocompatible and could potentially be explored for biomedical applications such as drug delivery systems, and wound dressings. This suggests that it might offer significant value for sustainable materials science, although specific applications have yet to be tested.

Refined linkage analysis of the sulphated marine polysaccharide fucoidan of Cladosiphon okamuranus with a focus on fucose.

Methylation followed by depolymerization and gas chromatography (GC) is an effective methodology for the linkage analysis of polysaccharides, including fucoidan, a sulphated algal polysaccharide. However, this sample material demands attention to experimental details to prevent aberrations in the analytical result. The use of deficient bases for methylation, the presence of water, analyte degradation during hydrolysis, and coelution of the target analytes during gas chromatography create doubts about published results. We therefore investigated critical parameters of the method and carefully optimized the steps of the protocol to ensure the integrity of the results for the fucose monomers. Fucoidan from Cladosiphon okamuranus was used as reference sample to determine the glycosidic bonds, and sulphate positions in the monomer. Fucoidan in protonated form was methylated in a strictly water-free environment using lithium dimsyl as base and methyl iodide for methylation. The methylated polymer was isolated by solid phase extraction, which was crucial to recover also the highly sulfated fraction. Hydrolysis was conducted with trifluoroacetic acid. To separate all target analytes in GC-FID/MS, a stationary phase with high cyanopropyl content (HP-88) was required, as the commonly employed phenyl siloxane phases result in co-elution, which distorts the result severely.

Strategies for multivariate characterization and classification of pulps and papers by near-infrared spectroscopy.

BACKGROUND: Multivariate calibration by Partial Least Squares (PLS) on near-infrared data has been applied successfully in several industrial sectors, including pulp and paper. The creation of multivariate calibration models relies on a set of well-characterised samples that cover the range of the intended application. However, sample sets that originate from an industrial process often show an uneven distribution of reference values. This can be addressed by curation of the reference data and the methodology for multivariate calibration. It needs to be better understood, how these approaches affect the quality and scope of the final model. RESULTS: We describe the effect of log10 transformation of the reference values, regular PLS, robust PLS, the newly introduced bin PLS, and their combinations to select more evenly distributed reference values for the quantification of five pulp characteristics (kappa number, R18, R10, cuen viscosity, and brightness; 200 samples) by near-infrared spectroscopy. The quality of the models was assessed by root mean squared error of prediction, calibration range, and coverage of sample types. The best models yielded uncertainty levels equivalent to that of the reference measurement. The optimal approach depended on the investigated reference value. SIGNIFICANCE: Robust PLS commonly gives the model with the lowest error, but this usually comes at the cost of a notably reduced calibration range. The other approaches rarely impacted the calibration range. None of them stood out as superior; their performance depended on the calibrated parameter. It is therefore worthwhile to investigate various calibration options to obtain a model that matches the requirements of the application without compromising calibration range and sample coverage.

Oxidized reducing ends in celluloses: Quantitative profiling relative to molar mass distribution by fluorescence labeling.

Fluorescence labeling with N-(1-naphthyl)ethylenediamine is highly effective for quantifying oxidized reducing end groups (REGs) in cellulosic materials. When combined with size exclusion chromatography in DMAc/LiCl, along with fluorescence / multiple-angle laser light scattering / refractive index detection, a detailed profile of C1-oxidized REGs relative to the molecular weight distribution of the cellulosic material can be obtained. In this work, the derivatization process was extensively optimized, to be carried out heterogeneously in the solvent N-methyl-2-pyrrolidone. Furthermore, we show that to achieve high selectivity for carboxyl groups at the C1 position, keto and aldehyde groups need to be selectively reduced (e.g., by NaBH4), and carboxyl groups other than at C1 need to be blocked (e.g., by methylation with (trimethylsilyl)diazomethane) prior to fluorescence labeling of carboxyl groups at C1 position. Finally, we demonstrate the practical value of the analytical method by measuring the content of the C1-oxidized REGs in cellulose samples after chemical (by Pinnick oxidation) or enzymatic (by treatment with C1-oxidizing LPMO enzymes) oxidation of various pulp samples.

Tapping the Full Potential of Infrared Spectroscopy for the Analysis of Technical Lignins.

We present an approach to overcome the challenges associated with the increasing demand of high-throughput characterization of technical lignins, a key resource in emerging bioeconomies. Our approach offers a resort from the lack of direct, simple, and low-cost analytical techniques for lignin characterization by employing multivariate calibration models based on infrared (IR) spectroscopy to predict structural properties of lignins (i. e., functionality, molar mass). By leveraging a comprehensive database of over 500 well-characterized technical lignin samples - a factor of 10 larger than previously used sets - our chemometric models achieved high levels of quality and statistical confidence for the determination of different functional group contents (RMSEPs of 4-16 %). However, the statistical moments of the molar mass distribution are still best determined by size-exclusion chromatography. Analyses of over 500 technical lignins offered also a great opportunity to provide information on the general variability in kraft lignins and lignosulfonates (from different origins). Overall, the effected savings in analysis time (>7 h), resources, and required sample mass combined with non-destructiveness of the measurement satisfy key demands for efficient high-throughput lignin analyses. Finally, we discuss the advantages, disadvantages, and limitations of our approach, along with critical insights into the associated chemical-analytical and spectroscopic challenges.

A novel approach to analyze the impact of lytic polysaccharide monooxygenases (LPMOs) on cellulosic fibres.

Enzymatic treatment of cellulosic fibres is a green alternative to classical chemical modification. For many applications, mild procedures for cellulose alteration are sufficient, in which the fibre structure and, therefore, the mechanical performance of cellulosic fibres are preserved. Lytic polysaccharide monooxygenases (LPMOs) bear a great potential to become a green reagent for such targeted cellulose modifications. An obstacle for wide implementation of LPMOs in tailored cellulose chemistry is the lack of suitable techniques to precisely monitor the LPMO impact on the polymer. Soluble oxidized cello-oligomers can be quantified using chromatographic and mass-spectrometric techniques. A considerable portion of the oxidized sites, however, remain on the insoluble cellulose fibres, and their quantification is difficult. Here, we describe a method for the simultaneous quantification of oxidized sites on cellulose fibres and changes in their molar mass distribution after treatment with LPMOs. The method is based on quantitative, heterogeneous, carbonyl-selective labelling with a fluorescent label (CCOA) followed by cellulose dissolution and size-exclusion chromatography (SEC). Application of the method to reactions of seven different LPMOs with pure cellulose fibres revealed pronounced functional differences between the enzymes, showing that this CCOA/SEC/MALS method is a promising tool to better understand the catalytic action of LPMOs.

Towards Tailored Dialdehyde Cellulose Derivatives: A Strategy for Tuning the Glass Transition Temperature.

The derivatization of dialdehyde cellulose (DAC) has received increasing attention in the development of sustainable thermoplastics. In this study, a series of dialcohol celluloses were generated by borohydride reduction, which exhibited glass transition temperature (Tg ) values ranging from 23 to 109 °C, depending on the initial degree of oxidation (DO) of the DAC intermediate. However, the DAC derivatives did not exhibit thermoplastic behavior when the DO of the modified DAC was below 26 %. The influence of introduced side chains was highlighted by comparing DAC-based thermoplastic materials obtained by either oximation or borohydride reduction. Our results provide insights into the generation of DAC-based thermoplastics and highlight a strategy for tailoring the Tg by adjusting the DO during the periodate oxidation step and selecting appropriate substituents in subsequent modifications.

Profiling of historical rag papers by their non-cellulosic polysaccharide composition.

Hemicellulose and pectin are noteworthy components of historical European rag papers, and have not been studied in detail so far. Rag papers were made from used textiles, and fiber-based utilities, such as ropes and bags. These had been prepared until the mid-19th century from plant-based fibers. Their polysaccharide composition could relate to their condition and history. This information can be expected to hold importance for the preservation and conservation of historical objects. We investigated a collection of rag papers of different age for their composition of non-cellulosic polysaccharides, and compared the findings with modern rag papers and wood pulps. Furthermore, a non-destructive determination of the hemicellulose and pectin content by near-infrared spectroscopy was developed. Historical rag papers had a lower hemicellulose/pectin content than pulps; the fractions of rhamnose, galactose, and arabinose were higher, while xylose was lower. In modern rag papers, xylose tended to be at the higher end of the range, which suggests a degradation of hemicelluloses/pectin over time or a change in raw materials and manufacturing. Rag papers also showed higher crystallinity than wood pulp papers. These findings provide insights into rag paper characteristics and offer potential classification methods.

Cellulose fibers and ellagitannin-rich extractives from rambutan (Nephelium Lappaceum L.) peel by an eco-friendly approach.

This study assesses the viability of an accelerated solvent extraction technique employing environmentally friendly solvents to extract ellagitannins while producing cellulose-rich fibers from rambutan peel. Two sequential extraction protocols were investigated: 1) water followed by acetone/water (4:1, v:v), and 2) acetone followed by acetone/water (4:1, v:v), both performed at 50 °C. The first protocol had a higher extraction yield of 51 %, and the obtained extractives featured a higher total phenolic (531.4 ± 22.0 mg-GAE/g) and flavonoid (487.3 ± 16.9 mg-QE/g) than the second protocol (495.4 ± 32.8 mg-GAE/g and 310.6 ± 31.4 mg-QE/g, respectively). The remaining extractive-free fibers were processed by bleaching using either 2 wt% sodium hydroxide with 3 wt% hydrogen peroxide or 4-5 wt% peracetic acid. Considering bleaching efficiency, yield, and process sustainability, the single bleaching treatment with 5 wt% of peracetic acid was selected as the most promising approach to yield cellulose-rich fibers. The samples were analyzed by methanolysis to determine the amount and type of poly- and oligosaccharides and studied by 13C solid-state nuclear magnetic resonance spectroscopy and thermal gravimetric analysis. The products obtained from the peels demonstrate significant potential for use in various sectors, including food, nutraceuticals, cosmetics, and paper production.

Lignin-Based Polyurethanes from the Blocked Isocyanate Approach: Synthesis and Characterization.

Lignin, the world's second most abundant biopolymer, has been investigated as a precursor of polyurethanes due to its high availability and large amount of hydroxyls present in its structure. Lignin-based polyurethanes (LPUs) are usually synthesized from the reaction between lignin, previously modified or not, and diisocyanates. In the present work, LPUs were prepared, for the first time, using the blocked isocyanate approach. For that, unmodified and hydroxypropylated Kraft lignins were reacted with 4,4'-methylene diphenyl diisocyanate in the presence of diisopropylamine (blocking agent). Castor oil was employed as a second polyol. The chemical modification was confirmed by 31P nuclear magnetic resonance (31P NMR) analysis, and the structure of both lignins was elucidated by a bidimensional NMR technique. The LPUs' prepolymerization kinetics was investigated by temperature-modulated optical refractometry and Fourier-transform infrared spectroscopy. The positive effect of hydroxypropylation on the reactivity of the Kraft lignin was verified. The structure of LPU prepolymers was accessed by bidimensional NMR. The formation of hindered urea-terminated LPU prepolymers was confirmed. From the results, the feasibility of the blocked isocyanate approach to obtain LPUs was proven. Lastly, single-lap shear tests were performed and revealed the potential of LPU prepolymers as monocomponent adhesives.

Antimicrobial, antioxidant, and sun protection potential of the isolated compounds from Spermacoce princeae (K. Schum).

BACKGROUND: Spermacoce princeae (K. Schum) has been used in the treatment of bacterial skin infections in Uganda. Pharmacological studies revealed that extracts of S. princeae exhibited antibacterial, antioxidant, and sun protection potential. This study aimed at isolating and identifying pure compounds from the extracts based on comprehensive analytical characterization by multiple analytical techniques. METHODS: The plant samples were extracted by sequential maceration using n-hexane, ethyl acetate, methanol, and distilled water. The compounds were isolated using a combination of chromatographic techniques and their structures were elucidated by multiple spectroscopic techniques. The antibacterial and antifungal activity determination of the isolated compounds was carried out using an agar well diffusion and potato dextrose assay against Pseudomonas aeruginosa, Staphylococcus aureus, Escherichia coli, Klebsiella pneumoniae, Candida albicans, and Aspergillus flavus while the antioxidant activity was screened with the 2,2-diphenyl-2-picryl-hydrazyl (DPPH) radical scavenging assay. The sun protection factor was determined using a Shimadzu Ultra Violet-visible (UV-VIS) double beam spectrophotometer between 290 to 320 nm. RESULTS: Eleven compounds; quercetin (1), kaempferol-3-O-rutinoside (2), rutin (3, 12), myo-inositol (4), asperulosidic acid (5), hexadecanoic acid (6), ß-sitosterol (7), stigmasterol (8), campesterol (9), ursolic acid (10), and ß-sitosterol glucoside (11) were identified in the S. princeae extracts. Compound 2 had good antifungal activity against C. albicans (zone of inhibition, 23.0 ± 0.1 mm). Compound 10 showed antibacterial and antifungal activity against S. aureus, P. aeruginosa, C. albicans, and A. flavus. Compound 2 had a good percentage radical scavenging effect (IC50 = 64.81 µg/ml) and a good sun protection factor (SPF = 26.83). CONCLUSION: This study reports the first-time isolation and identification of compounds 1 to 11 from S. princeae, which contribute to its antimicrobial, antioxidant, and sun protection potential.

Hemocompatibility of cellulose phosphate aerogel membranes with potential use in bone tissue engineering.

Cellulose is an appealing material for tissue engineering. In an attempt to overcome some obstacles with cellulose II cell scaffolding materials related to insufficient biomineralization, lack of micron-size porosity, and deficiency in surface charge, respective solutions have been proposed. These included covalent phosphorylation of different cellulose materials targeting relatively low degrees of substitution (DS 0.18-0.23) and processing these cellulose derivatives into scaffolding materials by a dissolution/coagulation approach employing the hitherto rarely used TBAF/DMSO/H2O system for cellulose dissolution. Here, we report bioactivity and preliminary hemocompatibility testing of dual-porous cellulose phosphate aerogels (contrasted with the phosphate-free reference) obtained via coagulation (water/ethanol), solvent exchange and scCO2 drying. Deposition of hydroxyapatite from simulated body fluid (7 days of immersion) revealed good bioactivity (1.5-2.2 mg Ca2+ per mg scaffold). Incubation of the scCO2-dried and rehydrated scaffolding materials in heparin anticoagulated human whole blood was conducted to study selected parameters of hemostasis (prothrombin F1+2 fragment, PF4, count of thrombocyte-leukocyte conjugates) and inflammatory response (C5a fragment, leukocyte activation marker CD11b). Adhesion of leukocytes on the surface of the incubated substrates was assessed by scanning electron and fluorescence microscopy (DAPI staining). The results suggest that phosphorylation at low DS does not increase platelet activation. However, a significant increase in platelet activation and thrombin formation was observed after a certain fraction of the negative surface charges had been compensated by Ca2+ ions. The combination of both phosphorylation and calcification turned out to be a potent means for controlling the inflammatory response, which was close to baseline level for some of the studied samples.

Debugging periodate oxidation of cellulose: Why following the common protocol of quenching excess periodate with glycol is a bad idea.

Periodate oxidation of cellulose to produce "dialdehyde cellulose" (DAC) has lately received increasing attention in sustainable materials development. Despite the longstanding research interest and numerous reported studies, there is still an enormous variation in the proposed preparation and work-up protocols. This apparently reduces comparability and causes reproducibility problems in DAC research. Two simple but prevalent work-up protocols, namely glycol quenching and filtration/washing, were critically examined and compared, resulting in this cautionary note. Various analytical techniques were applied to quantify residual iodine species and organic contaminations from quenching side reactions. The commonly practiced glycol addition cannot remove all oxidising iodine compounds. Both glycol and the formed formaldehyde are incorporated into DAC's polymeric structure. Quenching of excess periodate with glycol can thus clearly be discouraged. Instead, simple washing protocols are recommended which do not bear the risk of side reactions with organic contaminants. While simple washing was sufficient for mildly oxidised celluloses, higher oxidised samples were more likely to trap residual (per)iodate, as determined by thiosulfate titration. For work-up, simple washing with water is proposed while determining potential iodine contaminations after washing with a simple colorimetric test and, if needed, removal of residual periodate by washing with an aqueous sodium thiosulfate solution.

Template-Directed Polymerization of Binary Acrylate Monomers on Surface-Activated Lignin Nanoparticles in Toughening of Bio-Latex Films.

Fabricating bio-latex colloids with core-shell nanostructure is an effective method for obtaining films with enhanced mechanical characteristics. Nano-sized lignin is rising as a class of sustainable nanomaterials that can be incorporated into latex colloids. Fundamental knowledge of the correlation between surface chemistry of lignin nanoparticles (LNPs) and integration efficiency in latex colloids and from it thermally processed latex films are scarce. Here, an approach to integrate self-assembled nanospheres of allylated lignin as the surface-activated cores in a seeded free-radical emulsion copolymerization of butyl acrylate and methyl methacrylate is proposed. The interfacial-modulating function on allylated LNPs regulates the emulsion polymerization and it successfully produces a multi-energy dissipative latex film structure containing a lignin-dominated core (16% dry weight basis). At an optimized allyl-terminated surface functionality of 1.04 mmol g-1 , the LNPs-integrated latex film exhibits extremely high toughness value above 57.7 MJ m-3 . With multiple morphological and microstructural characterizations, the well-ordered packing of latex colloids under the nanoconfinement of LNPs in the latex films is revealed. It is concluded that the surface chemistry metrics of colloidal cores in terms of the abundance of polymerization-modulating anchors and their accessibility have a delicate control over the structural evolution of core-shell latex colloids.

From liquid to solid-state, solvent-free oxidative ammonolysis of lignins - an easy, alternative approach to generate "N-lignins".

A new chemical modification protocol to generate N-lignins is presented, based on Indulin AT and Mg2+-lignosulfonate. The already known ammonoxidation reaction in liquid phase was used as a starting point and stepwise optimised towards a full solid-state approach. The "classical" liquid ammonoxidation products, the transition products from the optimization trials, as well as the "solid-state" products were comprehensively analysed and compared to the literature. The N-lignins obtained with the conventional ammonoxidation protocol showed the same properties as reported. Their molar mass distributions and the hydroxy group contents, hitherto not accessible due to solubility problems, were measured according to a recently reported protocol. N-Indulin showed an N-content up to 11 wt% and N-lignosulfonate up to 16 wt%. The transition experiments from liquid to solid-state gave insights into the influence of chemical components and reaction conditions. The use of a single chemical, the urea-hydrogen peroxide complex (UHP, "carbamide peroxide"), was sufficient to generate N-lignins with satisfying N-content. This chemical acts both as an N-source and as the oxidant. Following the optimization, a series of solid-state ammonoxidation tests were carried out. High N-contents of 10% in the case of Indulin and 11% in the case of lignosulfonate were obtained. By varying the ratio of UHP to lignin, the N-content can be controlled. Structural analysis showed that the N is organically bound to the lignin, similar to the "classical" ammonoxidation products obtained under homogeneous conditions. Overall, a new ammonoxidation protocol was developed which does not require an external gas supply nor liquids or dissolved reactants. This opens the possibility for carrying out the lignin modification in closed continuous reactor systems, such as extruders. The new, facile solid-state protocol will hopefully help N-lignins to find more consideration as a fertilizing material and in soil-improving materials.

Exploring Alkyl-O-Alkyl Ether Structures in Softwood Milled Wood Lignins.

Recent studies have suggested that there are significant amounts of various alkyl ether (Alk-O-Alk; Alk = alkyl) moieties in a spruce native lignin preparation, milled wood lignin (SMWL). However, the comprehensive NMR assignment to these moieties has not been addressed yet. This study focused on investigating different types of Alk-O-Alk structures at the α- and γ-positions of the lignin side chain in an heteronuclear single-quantum coherence (HSQC) spectrum of SMWL using experimental NMR data of lignin and synthesized model compounds. Ambiguous structural features were predicted by computer simulation of 1H and 13C NMR spectra to complement the experimental NMR data. As a result, specific regions in the HSQC spectrum were attributed to different Alk-O-Alk moieties of Alk-O-Alk/ß-O-4 and Alk-O-Alk/ß-ß' structures. However, the differences between the specific regions were rather subtle; they were not well separated from each other and some major lignin moieties. Furthermore, SMWL contained a large variety of Alk-O-Alk moieties but in minute individual amounts, resulting in rather broad, superimposing resonances. Thus, evaluation did not allow assigning individual types of Alk-O-Alk moieties from the HSQC spectra; instead, they were quantified as total (α- and γ-linked) Alk-O-Alk based on the balance of structural units in the 13C NMR spectra. At last, potential formation mechanisms of various Alk-O-Alk ether structures in lignin biosynthesis, lignin aging, and during ball milling of wood were hypothesized and discussed.

Reductive Amination of Dialdehyde Cellulose: Access to Renewable Thermoplastics.

The reductive amination of dialdehyde cellulose (DAC) with 2-picoline borane was investigated for its applicability in the generation of bioderived thermoplastics. Five primary amines, both aliphatic and aromatic, were introduced to the cellulose backbone. The influences of the side chains on the course of the reaction were examined by various analytical techniques with microcrystalline cellulose as a model compound. The obtained insights were transferred to a 39%-oxidized softwood kraft pulp to study the thermal properties of thereby generated high-molecular-weight thermoplastics. The number-average molecular weights (Mn) of the diamine celluloses, ranging from 60 to 82 kD, were investigated by gel permeation chromatography. The diamine celluloses exhibited glass transition temperatures (Tg) from 71 to 112 °C and were stable at high temperatures. Diamine cellulose generated from aniline and DAC showed the highest conversion, the highest Tg (112 °C), and a narrow molecular weight distribution (D̵ of 1.30).

Silviridoside: A New Triterpene Glycoside from Silene viridiflora with Promising Antioxidant and Enzyme Inhibitory Potential.

A new triterpene glycoside, silviridoside, was isolated from the aerial parts of Silene viridiflora (Caryophyllaceae) using different chromatographic techniques. The structure of silviridoside was comprehensively elucidated as 3-O-ß-D-galacturonopyranosyl-quillaic acid 28-O-ß-D-glucopyranosyl-(1→2)-[α-L-rhamnopyranosyl-(1→3)]-ß-D-fucopyranosyl ester by one- and two-dimensional nuclear magnetic resonance (NMR) spectroscopy and high-resolution mass spectrometry (HR-MS). Silviridoside showed promising antioxidant activity in different antioxidant assays such as 2,2-diphenyl-1-picrylhydrazyl (DPPH) (2.32 mg TE/g), 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) (1.24 mg TE/g), cupric-reducing antioxidant capacity (CUPRAC) (9.59 mg TE/g), ferric-reducing antioxidant power (FRAP) (5.13 mg TE/g), phosphomolybdenum (PHD) (0.28 mmol TE/g), and metal-chelating (MCA) (6.62 mg EDTA/g) assays. It exhibited a good inhibitory potential on acetylcholinesterase (AChE) (2.52 mg GALAE/g), butyrylcholinesterase (BChE) (7.16 mg GALAE/g), α-amylase (0.19 mmol ACAE/g), α-glucosidase (1.21 mmol ACAE/g), and tyrosinase (38.83 mg KAE/g). An in silico evaluation of the pharmacodynamic, pharmacokinetic, and toxicity properties of silviridoside showed that the new compound exhibited reasonable pharmacodynamic and pharmacokinetic properties without any mutagenic effect, but slight toxicity. Thus, it could be concluded that silviridoside could act as a promising lead drug for pharmaceutical and nutraceutical developments to combat oxidative stress and various disorders, but a future optimization is necessary.

Assessment of Electrothermal Pretreatment of Rambutan (Nephelium lappaceum L.) Peels for Producing Cellulose Fibers.

Agroindustrial wastes are renewable sources and the most promising sustainable alternative to lignocellulosic biomass for cellulose production. This study assessed the electrothermal pretreatment of rambutan peel (RP) for producing cellulose fibers. The pretreatment was carried out by Ohmic heating at a solid-to-liquid ratio of 1:10 (w/v) in a water/ethanol (1:1, v/v) mixture as the electrical transmission medium at 60 ± 1 °C for different holding times (15, 30, and 60 min). Ohmic heating did not significantly influence the total fiber yield for the various holding times. However, the compositions of the samples in terms of extractives, lignin, hemicellulose, and α-cellulose content were significantly influenced. In addition, the electrothermal pretreatment method reduced the bleaching time of RP by 25%. The pretreated fibers were thermally stable up to 240 °C. Ohmic heating pretreatment times of 15 and 30 min were found most promising, reducing the required bleaching chemicals and increasing the α-cellulose yield. The pretreated bleached cellulose fibers had similar properties to nontreated bleached fibers and could be efficiently processed into stable gels of strong shear-thinning behavior with potential application as rheology modifiers in food products. Our results demonstrate that rambutan peel could serve as a promising sustainable alternative to woody biomass for cellulose production. Ohmic heating meets the requirements for industrial applications as it is eco-friendly, improves the efficiency and energy consumption in fiber processing, and could as well be included in the processing of similar food wastes.