RESUMEN
The development of flexible electronics has increased the demand for wearable pressure sensors that can be used to monitor various biomedical signals. In this context, pressure sensors based on zinc oxide (ZnO) have great potential since, besides the biocompatibility and biodegradability of this metal oxide, it also has piezoelectric properties. The common feature of these sensors is the alignment of the ZnO nanostructures in the strain direction. This alignment is achieved through a three-stage procedure: deposition of a ZnO nanoparticle layer (seed layer) followed by its patterning and the subsequent growth of nanostructures from the seed layer nanoparticles. Herein, a process compatible with industrial scale for depositing seed layers by flexographic printing is proposed, allowing seed layers to be deposited and patterned swiftly and efficiently in a single step on flexible indium tin oxide coated polyethylene terephthalate substrates, significantly decreasing the time and cost required to produce pressure sensors. The growth conditions of ZnO nanorods on these substrates were also studied to analyze their influence on the morphological and structural characteristics of the nanostructures. Nanorods with length of (0.27 ± 0.04) µm and density of (296 ± 6) nanorods per µm2 were obtained in microwave-assisted hydrothermal syntheses carried out at 100 °C for 30 min, with a 1 M zinc acetate seed layer and using an equimolar growth solution of zinc nitrate and hexamethylenetetramine. These conditions were used to produce ZnO-based pressure sensors with two patterns (one square and 16 individual squares). Although the single square sensors displayed a higher average output voltage ((12 ± 5) V for an impact pressure of 150 kPa), their response was considerably more variable than the patterned sensors (with 16 squares), which displayed an average output voltage of (8 ± 2) V under an applied pressure of 150 kPa and sensitivity values of (0.06 ± 0.01) V kPa-1, demonstrating their potential for wearables and portable electronics.
RESUMEN
Poly(p-xylylene) derivatives, widely known as Parylenes, have been considerably adopted by the scientific community for several applications, ranging from simple passive coatings to active device components. Here, we explore the thermal, structural, and electrical properties of Parylene C, and further present a variety of electronic devices featuring this polymer: transistors, capacitors, and digital microfluidic (DMF) devices. We evaluate transistors produced with Parylene C as a dielectric, substrate, and encapsulation layer, either semitransparent or fully transparent. Such transistors exhibit steep transfer curves and subthreshold slopes of 0.26 V/dec, negligible gate leak currents, and fair mobilities. Furthermore, we characterize MIM (metal-insulator-metal) structures with Parylene C as a dielectric and demonstrate the functionality of the polymer deposited in single and double layers under temperature and AC signal stimuli, mimicking the DMF stimuli. Applying temperature generally leads to a decrease in the capacitance of the dielectric layer, whereas applying an AC signal leads to an increase in said capacitance for double-layered Parylene C only. By applying the two stimuli, the capacitance seems to suffer from a balanced influence of both the separated stimuli. Lastly, we demonstrate that DMF devices with double-layered Parylene C allow for faster droplet motion and enable long nucleic acid amplification reactions.
RESUMEN
The contamination of water resources by pollutants resulting from human activities represents a major concern nowadays. One promising alternative to solve this problem is the photocatalytic process, which has demonstrated very promising and efficient results. Oxide nanostructures are interesting alternatives for these applications since they present wide band gaps and high surface areas. Among the photocatalytic oxide nanostructures, zinc tin oxide (ZTO) presents itself as an eco-friendly alternative since its composition includes abundant and non-toxic zinc and tin, instead of critical elements. Moreover, ZTO nanostructures have a multiplicity of structures and morphologies possible to be obtained through low-cost solution-based syntheses. In this context, the current work presents an optimization of ZTO nanostructures (polyhedrons, nanoplates, and nanoparticles) obtained by microwave irradiation-assisted hydrothermal synthesis, toward photocatalytic applications. The nanostructures' photocatalytic activity in the degradation of rhodamine B under both ultraviolet (UV) irradiation and natural sunlight was evaluated. Among the various morphologies, ZTO nanoparticles revealed the best performance, with degradation > 90% being achieved in 60 min under UV irradiation and in 90 min under natural sunlight. The eco-friendly production process and the demonstrated ability of these nanostructures to be used in various water decontamination processes reinforces their sustainability and the role they can play in a circular economy.
RESUMEN
The degradation of organic pollutants in wastewaters assisted by oxide semiconductor nanostructures has been the focus of many research groups over the last decades, along with the synthesis of these nanomaterials by simple, eco-friendly, fast, and cost-effective processes. In this work, porous zinc oxide (ZnO) nanostructures were successfully synthesized via a microwave hydrothermal process. A layered zinc hydroxide carbonate (LZHC) precursor was obtained after 15 min of synthesis and submitted to different calcination temperatures to convert it into porous ZnO nanostructures. The influence of the calcination temperature (300, 500, and 700 °C) on the morphological, structural, and optical properties of the ZnO nanostructureswas investigated. All ZnO samples were tested as photocatalysts in the degradation of rhodamine B (RhB) under UV irradiation and natural sunlight. All samples showed enhanced photocatalytic activity under both light sources, with RhB being practically degraded within 60 min in both situations. The porous ZnO obtained at 700 °C showed the greatest photocatalytic activity due to its high crystallinity, with a degradation rate of 0.091 and 0.084 min-1 for UV light and sunlight, respectively. These results are a very important step towards the use of oxide semiconductors in the degradation of water pollutants mediated by natural sunlight.
RESUMEN
The current trend for smart, self-sustainable, and multifunctional technology demands for the development of energy harvesters based on widely available and environmentally friendly materials. In this context, ZnSnO3 nanostructures show promising potential because of their high polarization, which can be explored in piezoelectric devices. Nevertheless, a pure phase of ZnSnO3 is hard to achieve because of its metastability, and obtaining it in the form of nanowires is even more challenging. Although some groups have already reported the mixing of ZnSnO3 nanostructures with polydimethylsiloxane (PDMS) to produce a nanogenerator, the resultant polymeric film is usually flat and does not take advantage of an enhanced piezoelectric contribution achieved through its microstructuration. Herein, a microstructured composite of nanowires synthesized by a seed-layer free hydrothermal route mixed with PDMS (ZnSnO3@PDMS) is proposed to produce nanogenerators. PFM measurements show a clear enhancement of d33 for single ZnSnO3 versus ZnO nanowires (23 ± 4 pm/V vs 9 ± 2 pm/V). The microstructuration introduced herein results in an enhancement of the piezoelectric effect of the ZnSnO3 nanowires, enabling nanogenerators with an output voltage, current, and instantaneous power density of 120 V, 13 µA, and 230 µW·cm-2, respectively. Even using an active area smaller than 1 cm2, the performance of this nanogenerator enables lighting up multiple LEDs and other small electronic devices, thus proving great potential for wearables and portable electronics.
RESUMEN
ZnSnO3 semiconductor nanostructures have several applications as photocatalysis, gas sensors, and energy harvesting. However, due to its multicomponent nature, the synthesis is far more complex than its binary counter parts. The complexity increases even more when aiming for low-cost and low-temperature processes as in hydrothermal methods. Knowing in detail the influence of all the parameters involved in these processes is imperative, in order to properly control the synthesis to achieve the desired final product. Thus, this paper presents a study of the influence of the physical parameters involved in the hydrothermal synthesis of ZnSnO3 nanowires, namely volume, reaction time, and process temperature. Based on this study a growth mechanism for the complex Zn:Sn:O system is proposed. Two zinc precursors, zinc chloride and zinc acetate, were studied, showing that although the growth mechanism is inherent to the material itself, the chemical reactions for different conditions need to be considered.
RESUMEN
Semiconductor nanowires are mostly processed by complex, expensive, and high temperature methods. In this work, with the intent of developing zinc tin oxide nanowires (ZTO NWs) by low-cost and low-complexity processes, we show a detailed study on the influence of chemical parameters in the hydrothermal synthesis of ZTO nanostructures at temperatures of only 200 °C. Two different zinc precursors, the ratio between zinc and tin precursors, and the concentration of the surfactant agent and of the mineralizer were studied. The type and the crystallinity of the nanostructures were found to be highly dependent on the used precursors and on the concentration of each reagent. Conditions for obtaining different ZTO nanostructures were achieved, namely, Zn2SnO4 nanoparticles and ZnSnO3 nanowires with length â¼600 nm, with the latter being reported for the first time ever by hydrothermal methods without the use of seed layers. Optical and electrical properties were analyzed, obtaining band gaps of 3.60 and 3.46 eV for ZnSnO3 and Zn2SnO4, respectively, and a resistivity of 1.42 kΩ·cm for single ZnSnO3 nanowires, measured using nanomanipulators after localized deposition of Pt electrodes by e-beam assisted gas decomposition. The low-temperature hydrothermal methods explored here proved to be a low-cost, reproducible, and highly flexible route to obtain multicomponent oxide nanostructures, particularly ZTO NWs. The diversity of the synthesized ZTO structures has potential application in next-generation nanoscale devices such as field effect nanotransistors, nanogenerators, resistive switching memories, gas sensors, and photocatalysis.
RESUMEN
This paper focuses on the analysis of InGaZnO thin-film transistors (TFTs) and circuits under the influence of different temperatures and bias stress, shedding light into their robustness when used in real-world applications. For temperature-dependent measurements, a temperature range of 15 to 85 °C was considered. In case of bias stress, both gate and drain bias were applied for 60 min. Though isolated transistors show a variation of drain current as high as 56% and 172% during bias voltage and temperature stress, the employed circuits were able to counteract it. Inverters and two-TFT current mirrors following simple circuit topologies showed a gain variation below 8%, while the improved robustness of a cascode current mirror design is proven by showing a gain variation less than 5%. The demonstration that the proper selection of TFT materials and circuit topologies results in robust operation of oxide electronics under different stress conditions and over a reasonable range of temperatures proves that the technology is suitable for applications such as smart food packaging and wearables.
