Chronic intracortical neural recordings using microelectrode arrays coated with PEDOT-TFB.

Microelectrode arrays have been extensively utilized to record extracellular neuronal activity for brain-machine interface applications. Modifying the microelectrodes with conductive polymers such as poly(3,4-ethylenedioxythiophene) (PEDOT) has been reported to be advantageous because it increases the effective surface area of the microelectrodes, thereby decreasing impedance and enhancing charge transfer capacity. However, the long term stability and integrity of such coatings for chronic recordings remains unclear. Previously, our group has demonstrated that use of the smaller counter ion tetrafluoroborate (TFB) during electrodeposition increased the stability of the PEDOT coatings in vitro compared to the commonly used counter ion poly(styrenesulfonate) (PSS). In the current work, we examined the long-term in vivo performance of PEDOT-TFB coated microelectrodes. To do so, we selectively modified half of the microelectrodes on NeuroNexus single shank probes with PEDOT-TFB while the other half of the microelectrodes were modified with gold as a control. The modified probes were then implanted into the primary motor cortex of rats. Single unit recordings were observed on both PEDOT-TFB and gold control microelectrodes for more than 12 weeks. Compared to the gold-coated microelectrodes, the PEDOT-TFB coated microelectrodes exhibited an overall significantly lower impedance and higher number of units per microelectrode specifically for the first four weeks. The majority of PEDOT-TFB microelectrodes with activity had an impedance magnitude lower than 400 kΩ at 1 kHz. Our equivalent circuit modeling of the impedance data suggests stability in the polymer-related parameters for the duration of the study. In addition, when comparing PEDOT-TFB microelectrodes with and without long-term activity, we observed a distinction in certain circuit parameters for these microelectrodes derived from equivalent circuit modeling prior to implantation. This observation may prove useful in qualifying PEDOT-TFB microelectrodes with a greater likelihood of registering long-term activity. Overall, our findings confirm that PEDOT-TFB is a chronically stable coating for microelectrodes to enable neural recording. STATEMENT OF SIGNIFICANCE: Microelectrode arrays have been extensively utilized to record extracellular neuronal activity for brain-machine interface applications. Poly(3,4-ethylenedioxythiophene) (PEDOT) has gained interest because of its unique electrochemical characteristics and its excellent intrinsic electrical conductivity. However, the long-term stability of the PEDOT film, especially for chronic neural applications, is unclear. In this manuscript, we report for the first time the use of highly stable PEDOT doped with tetrafluoroborate (TFB) for long-term neural recordings. We show that PEDOT-TFB coated microelectrodes on average register more units compared to control gold microelectrodes for at least first four weeks post implantation. We collected the in vivo impedance data over a wide frequency spectrum and developed an equivalent circuit model which helped us determine certain parameters to distinguish between PEDOT-TFB microelectrodes with and without long-term activity. Our findings suggest that PEDOT-TFB is a chronically stable coating for neural recording microelectrodes. As such, PEDOT-TFB could facilitate chronic recordings with ultra-small and high-density neural arrays.

Improving the performance of poly(3,4-ethylenedioxythiophene) for brain-machine interface applications.

Conducting polymers, especially poly(3,4-ethylenedioxythiophene) (PEDOT) based materials, are important for developing highly sensitive and microscale neural probes. In the present work, we show that the conductivity and stability of PEDOT can be significantly increased by switching the widely used counter anion poly(styrenesulfonate) (PSS) to the smaller tetrafluoroborate (TFB) anion during the electrodeposition of the polymer. Time-dependent impedance measurements of polymer modified implantable microwires were conducted in physiological buffer solutions under accelerated aging conditions and the relative stability of PEDOT:PSS and PEDOT:TFB modified microwires was compared over time. This study was also extended to carbon nanotube (CNT) incorporated PEDOT:PSS which, according to some reports, is claimed to enhance the stability and electrical performance of the polymer. However, no noticeable difference was observed between PEDOT:PSS and CNT:PEDOT:PSS in our measurements. At the biologically relevant frequency of 1kHz, PEDOT:TFB modified microwires exhibit approximately one order of magnitude higher conductivity and demonstrate enhanced stability over both PEDOT:PSS and CNT:PEDOT:PSS modified microwires. In addition, PEDOT:TFB is not neurotoxic and we show the proof-of-concept for both in vitro and in vivo neuronal recordings using PEDOT:TFB modified microelectrode arrays and chronic electrodes, respectively. Our findings suggest that PEDOT:TFB is a promising conductive polymer coating for the recording of neural activities.

Histocompatibility and in vivo signal throughput for PEDOT, PEDOP, P3MT, and polycarbazole electrodes.

Stimulation and recording of the in vivo electrical activity of neurons are critical functions in contemporary biomedical research and in treatment of patients with neurological disorders. The electrodes presently in use tend to exhibit short effective lifespans due to degradation of signal transmission resulting from the tissue response at the electrode-brain interface, with signal throughput suffering most at the low frequencies relevant for biosignals. To overcome these limitations, new electrode designs to minimize tissue responses, including conducting polymers (CPs) have been explored. Here, we report the short-term histocompatibility and signal throughput results comparing platinum and CP-modified platinum electrodes in a Sprague-Dawley rat model. Two of the polymers tested elicited significantly decreased astrocyte responses relative to platinum. These polymers also showed improved signal throughput at low frequencies and comparable signal-to-noise ratios during targeted intracranial electroencephalograms. These results suggest that CP electrodes may present viable alternatives to the metal electrodes that are currently in use.

Near-ohmic behavior for conducting polymers: extension beyond PEDOT on gold-plated platinum to other polymer-counterion/substrate combinations.

Conducting polymers constitute a class of materials for which electrochemical and electron transport properties are a function not only of their chemical identity but also of their complex morphology. In this paper, we investigate and compare the frequency dependence behavior of the impedance of poly(3,4-ethylenedioxythiophene), or PEDOT, and that of poly(3,4-ethylenedioxypyrrole), or PEDOP, which are doped with a series of polyatomic anions during electrodeposition. We also contrast the behavior of PEDOT on Pt|Au, Pt, glassy carbon, and gold. Initial results for polycarbazole, PCz, electrodes are, in addition, included. Deposition parameters were adjusted to produce morphologically similar films for PEDOT, PEDOP, and PCz. In doing so, we have been successful in producing frequency-independent impedance behavior similar to that previously reported for PEDOT on Pt|Au. Although the impedance behavior of these polymers appears to be primarily determined by morphological features, the impact of counterion identity (beyond ionic charge transport) is also discussed. These studies suggest that choice of polymer/dopant combination and electrodeposition parameters can be manipulated to tune the impedance characteristics of electrodes, thereby optimizing them for capacitive or faradaic charge injection, or some combination of the two.

A more informative approach for characterization of polymer monolithic phases: small angle neutron scattering/ultrasmall angle neutron scattering.

Neutron scattering techniques have been used frequently to characterize geological specimens and to determine the structures of glasses and of polymers as solutions, suspensions, or melts. Little work has been reported on their application in determining polymers' structural properties relevant to separations. Here, we present a comparison of characterization results from nitrogen porosimetry and from combined small angle neutron scattering (SANS) and ultrasmall angle neutron scattering (USANS) experiments. We show that SANS is extremely sensitive to the pore characteristics. Both approaches can provide information about porosity and pore characteristics, but the neutron scattering techniques provide additional information in the form of the surface characteristics of the pores and their length scales. Fits of the scattering data show that cylindrical pores are present with diameters down to 0.6 µm and that, for length scales down to approxmately 20 Å, the material shows self-similar (fractal) slopes of -3.4 to -3.6. Comparison of these characteristics with other examples from the scattering literature indicate that further investigation of their meaning for chromatographic media is required.

Miniemulsion synthesis of metal-oxo cluster containing copolymer nanobeads.

Hybrid nanobeads containing either a manganese-oxo or manganese-iron-oxo cluster have been prepared via the miniemulsion polymerization technique. Two new ligand substituted oxo clusters, Mn(12)O(12)(VBA)(16)(H(2)O)(4) and Mn(8)Fe(4)O(12)(VBA)(16)(H(2)O)(4) (where VBA = 4-vinylbenzoate), have been prepared and characterized. Polymerization of the functionalized metal-oxo clusters with styrene under miniemulsion conditions produced monodispersed polymer nanoparticles as small as ~60 nm in diameter. The metal-oxo polymer nanobeads were fully characterized in terms of synthetic parameters, composition, structure, and magnetic properties.

Charge transport in conducting polymers: insights from impedance spectroscopy.

This tutorial review gives a brief introduction to impedance spectroscopy and discusses how it has been used to provide insight into charge transport through conducting polymers, particularly when the polymers are used as electrodes for solution studies or the design of electrodes for biomedical applications. As such it provides both an introduction to the topic and references to both classic and contemporary work for the more advanced reader.