RESUMEN
Cotton textiles modified with copper compounds have a documented mechanism of antimicrobial action against bacteria, fungi, and viruses. During the COVID-19 pandemic, there was pronounced interest in finding new solutions for textile engineering, using modifiers and bioactive methods of functionalization, including introducing copper nanoparticles and complexes into textile products (e.g. masks, special clothing, surface coverings, or tents). However, copper can be toxic, depending on its form and concentration. Functionalized waste may present a risk to the environment if not managed correctly. Here, we present a model for managing copper-modified cotton textile waste. The process includes pressure and temperature-assisted hydrolysis and use of the hydrolysates as a source of sugars for cultivating yeast and lactic acid bacteria biomass as valuable chemical compounds.
RESUMEN
The main goal of this study was to modify the activity of Pd/TiO2/Ti catalyst in the reaction of CO oxidation by the addition of Zn. Plasma electrolytic oxidation (PEO) of Ti wire was conducted to produce a uniform porous layer of TiO2. A mixture of Pd and Zn was then introduced by means of adsorption. After reduction treatment, the activity of the samples was examined by oxidation of 5% CO in a temperature range from 80-350 °C. Model catalysts with sufficient amounts of the metals for physico-chemical investigation were prepared to further investigate the reaction between Pd and Zn during CO oxidation. The structures and compositions of the samples were investigated using scanning electron microscopy with energy dispersive spectroscopy (SEM-EDS), time-of-flight secondary ion mass spectrometry (TOF-SIMS), inductively coupled plasma mass spectrometry (ICP-MS), Fourier transform infrared (FTIR), and X-ray diffraction (XRD). Modification of Pd/TiO2/Ti catalyst by Zn with a Pd:Zn atomic ratio of 2:1 decreased the temperature of complete CO oxidation from 220 °C for Pd/TiO2/Ti to 180 °C for Pd-Zn/TiO2/Ti. The temperature of 50% CO conversion on Pd-Zn(2:1)/TiO2/Ti was around 55 °C lower than in the reaction on monometallic Pd catalyst. The addition of Zn to the Pd catalyst lowered the binding energy of CO on the surface and improved the dissociative adsorption of oxygen, facilitating the oxidation of CO. FTIR showed that the bridging form of adsorbed CO is preferred on bimetallic systems. Analysis of the surface compositions of the samples (SEM-EDS, TOF-SIMS) showed higher amounts of oxygen on the bimetallic systems.
RESUMEN
A porous TiO2 layer was prepared with the plasma electrolytic oxidation (PEO) of Ti. In a further step, Pd was deposited on the TiO2 surface layer using the adsorption method. The activity of the Pd/TiO2/Ti catalyst was investigated during the oxidation of CO to CO2 in a mixture of air with 5% CO. The structure of the catalytic active layer was studied using a scanning electron microscope equipped with an energy dispersive spectrometer (SEM-EDS), time-of-flight secondary ion mass spectrometry (TOF-SIMS), inductively coupled plasma mass spectrometry (ICP-MS), and X-ray diffraction (XRD). The PEO process provided a porous TiO2 layer with a uniform thickness in the range of 5-10 µm, which is desirable for the production of Pd-supported catalysts. A TOF-SIMS analysis showed the formation of Pd nanoparticles after the adsorption treatment. The conversion of CO to CO2 in all samples was achieved at 150-280 °C, depending on the concentration of Pd. The composition of Pd/ TiO2/Ti was determined using ICP-MS. The optimum concentration of Pd on the surface of the catalyst was approximately 0.14% wt. This concentration was obtained when a 0.4% PdCl2 solution was used in the adsorption process. Increasing the concentration of PdCl2 did not lead to a further improvement in the activity of Pd/ TiO2/Ti.