Boosting Contact Electrification by Amorphous Polyvinyl Alcohol Endowing Improved Contact Adhesion and Electrochemical Capacitance.

Ion conductive hydrogels are relevant components in wearable, biocompatible, and biodegradable electronics. Polyvinyl-alcohol (PVA) homopolymer is often the favored choice for integration into supercapacitors and energy harvesters as in sustainable triboelectric nanogenerators (TENGs). However, to further improve hydrogel-based TENGs, a deeper understanding of the impact of their composition and structure on devices performance is necessary. Here, it is shown how ionic hydrogels based on an amorphous-PVA (a-PVA) allow to fabricate TENGs that outperform the one based on the homopolymer. When used as tribomaterial, the Li-doped a-PVA allows to achieve a twofold higher pressure sensitivity compared to PVA, and to develop a conformable e-skin. When used as an ionic conductor encased in an elastomeric tribomaterial, 100 mW cm-2 average power is obtained, providing 25% power increase compared to PVA. At the origin of such enhancement is the increased softness, stronger adhesive contact, higher ionic mobility (> 3,5-fold increase), and long-term stability achieved with Li-doped a-PVA. These improvements are attributed to the high density of hydroxyl groups and amorphous structure present in the a-PVA, enabling a strong binding to water molecules. This work discloses novel insights on those parameters allowing to develop easy-processable, stable, and highly conductive hydrogels for integration in conformable, soft, and biocompatible TENGs.

Direct Laser Writing of Chitosan-Borax Composites: Toward Sustainable Electrochemical Sensors.

In this study, the laser-induced graphitization process of sustainable chitosan-based formulations was investigated. In particular, optimal lasing conditions were investigated alongside the effect of borax concentration in the chitosan matrix. In all cases, it was found that the obtained formulations were graphitizable with a CO2 laser. This process gave rise to the formation of high surface area, porous, and electrically conductive laser-induced graphene (LIG) structures. It was found that borax, as a cross-linker of chitosan, enabled the graphitization process when its content was ≥30 wt % in the chitosan matrix, allowing the formation of an LIG phase with a significant content of graphite-like structures. The graphitization process was investigated by thermogravimetric analysis (TGA), Raman, X-ray photoemission (XPS), and Fourier transform infrared (FTIR) spectroscopies. LIG electrodes obtained from CS/40B formulations displayed a sheet resistance as low as 110 Ω/sq. Electrochemical characterization was performed after a 10 min electrode activation by cycling in 1 M KCl. A heterogeneous electron transfer rate, k0, of 4 × 10-3 cm s-1 was determined, indicating rapid electron transfer rates at the electrode surface. These results show promise for the introduction of a new class of sustainable composites for LIG electrochemical sensing platforms.

Neuroscientific Methods for Exploring User Perceptions While Dealing With Mobile Advertising: A Novel and Integrated Approach.

Display and native ads represent two of the most widely used digital advertising formats employed by advertisers that aim to grab the attention of online users. In recent years, the native format has become very popular because it relies on deceptive features that make harder the recognition of its advertising nature, reducing avoiding behaviors such as the banner blindness phenomena, traditionally associated to display advertising, and so increasing its advertising effectiveness. The present study, based on a forefront research protocol specifically designed for the advertising research on smartphone devices, aims to investigate through neurophysiological and self-reported measures, the perception of display and native ads placed within article webpages, and to assess the efficacy of an integrated approach. Eye-tracking results showed higher visual attention and longer viewing time associated with native advertisements in comparison to traditional display advertisements, confirming and extending evidence provided by previous research. Despite a significantly higher rate of self-reported advertising intent was detected for articles containing display ads when compared to articles containing native ads, no differences have been found while performing the same comparison for the neurophysiological measures of emotional involvement and approaching motivation of for the self-reported measures of pleasantness and annoyance. Such findings along with the employment of an innovative research protocol, contribute to providing further cues to the current debate related to the effectiveness of two of the most widely used digital advertising formats.

Chemically Functionalized Cellulose Nanocrystals as Reactive Filler in Bio-Based Polyurethane Foams.

Cellulose Nanocrystals, CNC, opportunely functionalized are proposed as reactive fillers in bio-based flexible polyurethane foams to improve, mainly, their mechanical properties. To overcome the cellulose hydrophilicity, CNC was functionalized on its surface by linking covalently a suitable bio-based polyol to obtain a grafted-CNC. The polyols grafted with CNC will react with the isocyanate in the preparation of the polyurethane foams. An attractive way to introduce functionalities on cellulose surfaces in aqueous media is silane chemistry by using functional trialkoxy silanes, X-Si (OR)3. Here, we report the synthesis of CNC-grafted-biopolyol to be used as a successful reactive filler in bio-based polyurethane foams, PUFs. The alkyl silanes were used as efficient coupling agents for the grafting of CNC and bio-polyols. Four strategies to obtain CNC-grafted-polyol were fine-tuned to use CNC as an active filler in PUFs. The effective grafting of the bio polyol on CNC was evaluated by FTIR analysis, and the amount of grafted polyol by thermogravimetric analysis. Finally, the morphological, thermal and mechanical properties and hydrophobicity of filled PUFs were thoughtfully assessed as well as the structure of the foams and, in particular, of the edges and walls of the cell foams by means of the Gibson-Ashby model. Improved thermal stability and mechanical properties of PU foams containing CNC-functionalized-polyol are observed. The morphology of the PU foams is also influenced by the functionalization of the CNC.

An anisotropic layer-by-layer carbon nanotube/boron nitride/rubber composite and its application in electromagnetic shielding.

Multifunctional polymer composites with anisotropic properties are attracting interest as they fulfil the growing demand of multitasking materials. In this work, anisotropic polymer composites have been fabricated by combining the layer-by-layer (LBL) filtration method with the alternative assembling of carbon nanotubes (CNTs) and hexagonal boron nitride flakes (hBN) on natural rubber latex particles (NR). The layered composites exhibit anisotropic thermal and electrical conductivities, which are tailored through the layer formulations. The best composite consists of four layers of NR modified with 8 phr (parts per Hundred Rubber) CNTs (∼7.4 wt%) and four alternate layers with 12 phr hBN (∼10.7 wt%). The composites exhibit an electromagnetic interference (EMI) shielding effectiveness of 22.41 ± 0.14 dB mm-1 at 10.3 GHz and a thermal conductivity equal to 0.25 W m-1 K-1. Furthermore, when the layered composite is used as an electrical thermal heater the surface reaches a stable temperature of ∼103 °C in approx. 2 min, with an input bias of 2.5 V.

Light-responsive and self-healing behavior of azobenzene-based supramolecular hydrogels.

HYPOTHESIS: Multi-component supramolecular hydrogels are gaining increasing interest as stimuli-responsive materials. To fully understand and possibly exploit the potential of such complex systems, the hierarchical structure of the gel network needs in-depth investigations across multiple length scales. We show that a thorough structural and rheological study represents a crucial pillar for the exploitation of this class of functional materials. EXPERIMENTS: Supramolecular hydrogels are prepared by self-assembly of hexadecyltrimethylammonium bromide (CTAB) and azobenzene-4,4'-dicarboxylic acid (AZO) in alkaline aqueous solution. The CTAB/AZO concentration was varied from ϕ = 0.25 to 4 wt% keeping the CTAB:AZO molar ratio fixed at 2:1. The systems were thoroughly studied through a combination of X-ray scattering, microscopy, rheological and spectroscopic analyses. FINDINGS: The CTAB/AZO solutions form a self-supporting gel with nanofibrillar structure below ~30 °C. The critical gelation concentration is ϕc = 0.45 wt%. Above this threshold, the gel elasticity and strength increase with CTAB/AZO content as ~(ϕ-ϕc)1. The hydrogels exhibit self-healing ability when left at rest after a stress-induced damage. Moreover, the light-induced isomerization of the AZO moieties provides the gel with light-responsiveness. Overall, the multi-stimuli responsiveness of the studied CTAB/AZO hydrogels makes them a solid starting point for the development of sensors for mechanical vibrations and UV/visible light exposure.

Greener Nanocomposite Polyurethane Foam Based on Sustainable Polyol and Natural Fillers: Investigation of Chemico-Physical and Mechanical Properties.

Nowadays, the chemical industry is looking for sustainable chemicals to synthesize nanocomposite bio-based polyurethane foams, PUs, with the aim to replace the conventional petrochemical precursors. Some possibilities to increase the environmental sustainability in the synthesis of nanocomposite PUs include the use of chemicals and additives derived from renewable sources (such as vegetable oils or biomass wastes), which comprise increasingly wider base raw materials. Generally, sustainable PUs exhibit chemico-physical, mechanical and functional properties, which are not comparable with those of PUs produced from petrochemical precursors. In order to enhance the performances, as well as the bio-based aspect, the addition in the polyurethane formulation of renewable or natural fillers can be considered. Among these, walnut shells and cellulose are very popular wood-based waste, and due to their chemical composition, carbohydrate, protein and/or fatty acid, can be used as reactive fillers in the synthesis of Pus. Diatomite, as a natural inorganic nanoporous filler, can also be evaluated to improve mechanical and thermal insulation properties of rigid PUs. In this respect, sustainable nanocomposite rigid PU foams are synthesized by using a cardanol-based Mannich polyol, MDI (Methylene diphenyl isocyanate) as an isocyanate source, catalysts and surfactant to regulate the polymerization and blowing reactions, H2O as a sustainable blowing agent and a suitable amount (5 wt%) of ultramilled walnut shell, cellulose and diatomite as filler. The effect of these fillers on the chemico-physical, morphological, mechanical and functional performances on PU foams has been analyzed.

Ultra-Light Reduced Graphene Oxide Based Aerogel/Foam Absorber of Microwave Radiation.

We present the polarization-dependent highly absorptive in Ka-band composition of conventional polyurethane foam filled with in situ synthesized aerogel coated by reduced graphene oxide (rGO). The rGO-based aerogel was in situ prepared into the open-cell polyurethane foam (PUF) skeleton through a bidirectional freeze-drying process. The aerogel is composed of the flat lamellas stacks, possessing the anisotropic structure and unique electromagnetic properties. Further improvement of the electromagnetic shielding ability was possible by the rGO coating introduction as a coupling layer between PUF and rGO-based aerogel. This enhances the overall conductivity of the resulting composites: 1.41 + 3.33i S/m vs. 0.9 + 2.45i S/m for PUF loaded with in situ synthesized aerogel without rGO coating.With this mechanically robust plane easy to process coating one could achieve -20 dB by power with the record light structure (0.0462 g/cm²). That could compete in view of the weight per cm² even with graphene-based absorbers comprising either dielectric matching elements or back metal reflectors, or both.

Nano-in-Nano Approach for Enzyme Immobilization Based on Block Copolymers.

We set up a facile approach for fabrication of supports with tailored nanoporosity for immobilization of enzymes. To this aim block copolymers (BCPs) self-assembly has been used to prepare nanostructured thin films with well-defined architecture containing pores of tailorable size delimited by walls with tailorable degree of hydrophilicity. In particular, we employed a mixture of polystyrene-block-poly(l-lactide) (PS-PLLA) and polystyrene-block-poly(ethylene oxide) (PS-PEO) diblock copolymers to generate thin films with a lamellar morphology consisting of PS lamellar domains alternating with mixed PEO/PLLA blocks lamellar domains. Selective basic hydrolysis of the PLLA blocks generates thin films, patterned with nanometric channels containing hydrophilic PEO chains pending from PS walls. The shape and size of the channels and the degree of hydrophilicity of the pores depend on the relative length of the blocks, the molecular mass of the BCPs, and the composition of the mixture. The strength of our approach is demonstrated in the case of physical adsorption of the hemoprotein peroxidase from horseradish (HRP) using 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) with H2O2 as substrate. The large surface area, the tailored pore sizes, and the functionalization with hydrophilic PEO blocks make the designed nanostructured materials suitable supports for the nanoconfinement of HRP biomolecules endowed with high catalytic performance, no mass-transfer limitations, and long-term stability.