RESUMEN
This study presents a novel approach to the development of high-performance supercapacitors through 3D printing technology. We synthesized a composite material consisting of silver-doped reduced graphene oxide (rGO) and dodecylbenzenesulfonic acid (DBSA)-doped polyaniline (PANI), which was further blended with polylactic acid (PLA) for additive manufacturing. The composite was extruded into filaments and printed into circular disc electrodes using fused deposition modeling (FDM). These electrodes were assembled into symmetric supercapacitor devices with a solid-state electrolyte. Electrochemical characterization, including cyclic voltammetry (CV) and galvanostatic charge-discharge (GCD) tests, demonstrated considerable mass-specific capacitance values of 136.2 F/g and 133 F/g at 20 mV/s and 1 A/g, respectively. The devices showed excellent stability, retaining 91% of their initial capacitance after 5000 cycles. The incorporation of silver nanoparticles enhanced the conductivity of rGO, while PANI-DBSA improved electrochemical stability and performance. This study highlights the potential of combining advanced materials with 3D printing to optimize energy storage devices, offering a significant advancement over traditional manufacturing methods.
RESUMEN
Herein, additive manufacturing, which is extremely promising in different sectors, has been adopted in the electrical energy storage field to fabricate efficient materials for supercapacitor applications. In particular, Al2O3-, steel-, and Cu-based microparticles have been used for the realization of 3D self-assembling materials covered with reduced graphene oxide to be processed through additive manufacturing. Functionalization of the particles with amino groups and a subsequent "self-assembly" step with graphene oxide, which was contextually partially reduced to rGO, was carried out. To further improve the electrical conductivity and AM processability, the composites were coated with a polyaniline-dodecylbenzene sulfonic acid complex and further blended with PLA. Afterward, they were extruded in the form of filaments, printed through the fused deposition modeling technique, and assembled into symmetrical solid-state devices. Electrochemical tests showed a maximum mass capacitance of 163 F/g, a maximum energy density of 15 Wh/Kg at 10 A/g, as well as good durability (85% capacitance retention within 5000 cycles) proving the effectiveness of the preparation and the efficiency of the as-manufactured composites.
RESUMEN
Supercapacitors have attracted considerable attention due to their advantages, including being lightweight and having rapid charge-discharge, a good rate capability, and high cyclic stability. Electrodes are one of the most important factors influencing the performance of supercapacitors. Herein, a three-dimensional network of rough and porous micropebbles of CeCu2Si2 has been prepared using a one-step procedure and tested for the first time as a supercapacitor electrode. The synthesized material was extensively characterized in a three-electrode configuration using different electrochemical techniques, such as cyclic voltammetry (CV), galvanostatic charge and discharge (GCD) tests, and electrochemical impedance spectroscopy (EIS). CeCu2Si2 shows rather high mass-capacitance values: 278 F/g at 1 A/g and 295 F/g at 10 mV/s. Moreover, the material exhibits remarkable long-term stability: 98% of the initial capacitance was retained after 20,000 cycles at 10 A/g and the Coulombic efficiency remains equal to 100% at the end of the cycles.
RESUMEN
Nowadays, iron (II) selenide (FeSe), which has been widely studied for years to unveil the high-temperature superconductivity in iron-based superconductors, is drawing increasing attention in the electrical energy storage (EES) field as a supercapacitor electrode because of its many advantages. In this study, very small FeSe particles were synthesized via a simple, low-cost, easily scalable, and reproducible solvothermal method. The FeSe particles were characterized using cyclic voltammetry (CV), galvanostatic charge/discharge (GCD) measurements, and electrochemical impedance spectroscopy (EIS), revealing enhanced electrochemical properties: a high capacitance of 280 F/g at 0.5 A/g, a rather high energy density of 39 Wh/kg and a corresponding power density of 306 W/kg at 0.5 A/g, an extremely high cycling stability (capacitance retention of 92% after 30,000 cycles at 1 A/g), and a rather low equivalent series resistance (RESR) of ~2 Ω.
RESUMEN
Herein, a surfactant-free, ethylene glycol-mediated synthesis of PtIr nanoalloys was optimized. In particular, a post-synthesis treatment was identified as the key step in order to determine the nanoparticles size and their organization in the nanostructure, depending on the presence of a reducing agent and on pressure conditions. After synthesis, the as-obtained nanomaterials were broadly characterized: SEM and TEM images, EDX maps and XRD spectra showed the formation of nanorods with a few nanometers size and similar quantitative compositions of platinum and iridium. Afterward, the electrocatalytic activity towards the methanol oxidation reaction of the synthesized nanomaterials was tested and the best sample, treated under a hydrogen/nitrogen flow at 10 bar, exhibits a negligible onset potential (0.058 V) and a very high If/Ib ratio (2.5). Moreover, the aforementioned sample was tested as an electrochemical sensor for the detection of small traces of ammonia in an aqueous solution with a limit of detection of 4.88 µM. The sensor was tested also in simulated wastewater coming from the fertilizer industry, showing proper operation and excellent selectivity.
